Summary of Contents for PTC Mirage 3000
- Page 1 Mirage Model 4000 Mirage Model 3000 Hydraulic Patient Chair Installation, Operation & User Manual 851 S. Lawson St. City of Industry, CA 91748 Phone 626-810-4337 Fax 626-810-4245 www.tpcdental.com REV. 1-1-13...
- Page 2 Important! It’s IMPERATIVE that you read this page before continuing. Failure to do so will result is wasted time during your installation… · All patient chairs are pre-wired with low voltage wiring. · All patient chairs are pre-wired with touch pad control cables.
-
Page 3: Table Of Contents
Table on Contents: Page GENERAL INFORMATION Transportation / Storage Information Unpacking instructions Installation and coordination Operation instructions Overview of foot controls Overview of touchpad controls Features Main PCB Board Wiring Schematic 1 Adjusting main flow control block Replacement Parts List CLEANING &... -
Page 4: General Information
GENERAL INFORMATION The dental chair is marked with a product identification label including manufacture, serial number and date of manufacture. This label is located on the front lower left cover under the seat cushion. The dental chair is marked with a caution symbol. -
Page 5: Unpacking Instructions
Mirage Model 4000 unpacking instructions Place the chair carton close to the planned area that you wish to install the dental chair. Do not turn the carton on its side as oil will drain out of the tank Figure 1 reservoir. -
Page 6: Installation And Coordination
Mirage Model 4000 Installation instructions Once the chair is in the desired location remove the 4 bolts shown in the image to the right. Place the lift bar in a safe place for future use. Once the bolts are removed your backrest bracket should look similar to the one shown to the right. - Page 7 Once the backrest bracket is in place, the 4 bolt holes should be aligned. Use the lock washer and bolts from step 1 to fasten the bracket in place. Insert and tighten the 4 bolts with the lock washers in place. Be sure not to over tighten the bolts www.tpcdental.com...
- Page 8 Installing the upholstery 1. Open the bolt package included in your upholstery box. 2. Locate the nuts and bolts shown in figure 1. 3. Attach the nuts to the bolts and place them in the backrest frame as shown in figure 2. Adjust the nut so that the head of the bolt and the back of the nut are able to slide up and down with little resistance in the backrest bracket.
- Page 9 1. Take the seat cushion out and place it upholstery side down. 2. Locate the rivet insert holes to mount the seat cushion hardware. 3. Use the Allen screws, lock washers and washers shown in figure 1 to attach the s-bracket shown in figure 2 to the upholstery 4.
- Page 10 1. Insert the chair seat cushion into the seat pan bracket notch shown in figure 1. You will notice that the seat pan is notched so that the bracket can slide into place and not move from left to right. 2.
-
Page 11: Operation Instructions
Mirage Model 4000 operation instructions Please take time out to read the features and to familiarize yourself with the chair. www.tpcdental.com... -
Page 12: Overview Of Foot Controls
Overview of foot control operations 1. Seat Height Adjustments To raise, press down on upper area of the foot control disc. To lower, press down on the lower area of the foot control disc. 2. Backrest Adjustments To raise, press down on right side of the foot control disc. To recline, press down on left side of foot control disc. -
Page 13: Overview Of Touchpad Controls
Overview of optional touchpad controls 1. Seat Height Adjustments To raise, press down on upper area of touch pad. To lower, press down on the lower area of touch pad. 2. Backrest Adjustments To raise, press down on right side of touch pad. To recline, press down on left side of touch pad. -
Page 14: Features
6. Safety Plate Safety plate is provided below base link cover to stop motion of chair when object is accidentally caught underneath. 7. Armrest Rotation Either armrest can be rotated outward by grasping the end portion of armrest, pulling upward and turning. - Page 15 Motion Limit Controls Function The Mirage Hydraulic Patient Chair does not use conventional mechanical or mercury limit switches. Motion of the chair base and backrest move variable resistances (potentiometers) making it possible for the control circuitry to continuously know the exact position of the base and backrest, not only when they hit the end of their travel.
-
Page 16: Main Pcb Board
Main PCB Board www.tpcdental.com... -
Page 17: Wiring Schematic 1
Wiring schematic 1 www.tpcdental.com... - Page 18 Wiring schematic www.tpcdental.com...
-
Page 19: Adjusting Main Flow Control Block
Operating Speed Controls Operating speeds are preset at factory, but can be changed if desired. · TV1 = Base up flow control · TV2 = Base down Flow Control · TV3 = Back up flow control · TV4 = Back down flow control When adjusting the flow control valves counter clockwise turns will open / increase flow. -
Page 20: Replacement Parts List
Mirage Model 4000 Replacement parts list Description Part Number Roller Base L M4000-008A Roller Base R M4000-009A Cast Back Roller M4000-010A Back Flange M4000-011A Cushion Frame M4000-012A U Bracket M4000-022 Backrest Frame M4000-025 Arm Rest flange 1 M4000-028 Arm Rest Flange 2 M4000-28A Arm Rest Bracket L M4000-029 Arm Rest Bracket R M4000-029A... - Page 21 Description Part Number Pump Cover M4000-015 Cushion cover/B M4000-023 Bottom Cushion M4000-024 Backrest Cushion M4000-026 Head Rest M4000-027 Rear Flange Cover M4000-030 L Side Cover M4000-031 R Side Cover M4000-031A Rear L side Cover M4000-032 Rear R Side Cover M4000-032A Backrest Cover M4000-033 Lower L Cover...
- Page 22 Description Part Number Cast Base M4000-001 R Arm Support M4000-002 L Arm Support M4000-003 M4000-006 Bottom Base Cover M4000-016 Bottom Pump T M4000-017 Top Pump Arm M4000-018 Top Pump T M4000-019 Connecting Rod M4000-036 Hydraulic Pump M4000-HYD www.tpcdental.com...
- Page 23 Description Part Number Cantilever M4000-004 Rotator Base M4000-005 Rotator Top M4000-007 Rotator Insert M4000-020 Break Clamp M4000-021 Cantilever Rod M4000-035 Cantilever Pins M4000-037 Break Clamp Rod M4000-038 Break Clamp Arm M4000-039 Hydraulic Pin M4000-040 Bracket Base M4000-044 Insert Base Connector M4000-045 Rollers Seat Pan M4000-RSP Hydraulic Piston...
-
Page 24: Cleaning & Disinfecting Guide
Mirage Hydraulic Patient Chair – Care and Maintenance No maintenance is required except normal care and cleaning. Clean vinyl upholstery and plastic components with mild soap and water. Barrier covers should be used on chairs for asepsis. Surface disinfecting chemical will eventually cause some discoloring of upholstery. Suggested Disinfectant Application Clean dirt and stains with mild soap and water. -
Page 25: Warranty
TPC 5 YEAR LIMITED WARRANTY Warranty Information All of our products sold are guaranteed to be free from defects in workmanship and materials for a 1 year from date of purchase, unless otherwise stated. TPC will repair or replace any defective part at no charge. -
Page 26: Trouble Shooting Guide
Mirage Model 4000 Troubleshooting Problem Cause Solution Dental Chair does not move No power Check power source up or down. Chair makes no Blown fuse Check fuse sound. Power switch off Check power switch Blown transformer Check transformer voltage 12vac Dental Chair will not move, Safety switch plate Check safety plate...
Need help?
Do you have a question about the Mirage 3000 and is the answer not in the manual?
Questions and answers