Advertisement
Quick Links
NORFIELD
MasterLine Multipoint Lock Fixture
IMPORTANT SAFETY INSTRUCTIONS
WARNING: When using electric tools, basic precautions should be followed to reduce
the risk of fire, electric shock and personal injury.
READ & FOLLOW ALL INSTRUCTIONS: This tool was designed for specific
applications. Norfield Industries strongly recommends that this tool NOT be modified
and/or used for applications other than those for which it was designed. If you have any
questions about additional applications or uses, DO NOT attempt those uses or
modifications until you have been advised by a qualified Norfield Representative.
Any and all modifications to or misuses of the tool will void all warranties
For any questions or concerns regarding the multi-point lock please contact:
NORFIELD IND
PO BOX 459
CHICO CA 95927
Telephone#: (800)824-6242
Fax#: (530)879-3140
www.Norfield.com
Avoid Dangerous Environments
Do not expose equipment in rain or use in damp conditions.
Do not use tool in presence of flammable liquids or gases.
Dress Properly
Do not wear loose clothing or jewelry. Loose clothing, drawstrings and jewelry can be
caught in moving parts. Wear protective hair covering to contain long hair.
ALWAYS Use Safety Glasses
Maintain Machine Tools Properly
Keep cutters sharp and clean for better and safer performance.
Always use correct-size cutters.
Inspect all electrical cords periodically and replace if damaged.
Disconnect Electrical Supply Cord
Advertisement
Summary of Contents for Norfield MasterLine Multipoint Lock Fixture
- Page 1 READ & FOLLOW ALL INSTRUCTIONS: This tool was designed for specific applications. Norfield Industries strongly recommends that this tool NOT be modified and/or used for applications other than those for which it was designed. If you have any questions about additional applications or uses, DO NOT attempt those uses or modifications until you have been advised by a qualified Norfield Representative.
- Page 2 Always disconnect cord before servicing, cleaning, changing cutters or adding accessories. Stay Alert Watch what you are doing. Use common sense. Do not operate equipment when you are tired or under the influence of medication, alcohol or drugs. SAVE THESE INSTRUCTIONS DOCUMENT NUMBER: 17-360...
-
Page 3: Additional Safety Instructions
ADDITIONAL SAFETY INSTRUCTIONS Use Only ½” Diameter Shank Router Bit Using a smaller shank could result in injury to the operator due to the distance the shank must protrude outside the router collet. Begin Routing With Router Base Firmly Against Template and Router Bit Retracted DO NOT Insert Router Bit Through Template Slot with Router Running This will greatly increase the risk of injury to the operator and increase the potential of... - Page 4 ½” diameter x 5-1/2” OAL (Overall Length) router bit: FOR53486 or equivalent. (use with 13/16” OD guide) TEMPLATE GUIDE 13/16” outside diameter guide: Norfield NOR62949 or equivalent (use with ½” dia. bit) and Norfield POR42237 nut. TEMPLATES A set of templates and alignment blocks for the specific hardware to be installed...
-
Page 5: Assembly And Operation
ASSEMBLY AND OPERATION This fixture is designed to work on square edged doors either 1-3/4” or 2-1/4” thick. TOOLS REQUIRED FOR SET-UP • Set of SAE hex keys (1/8”, 5/32” & 3/16”) BASIC ASSEMBY The lock installation instructions should be read carefully to determine if the lock location should be referenced from the top or the bottom of the door. - Page 6 The following setup is for reference from the top of the door. Reference figures 1, 2 & 3 Note: This will position the lock so that the lock handle will always be the same distance from the top of the door. BASE UNITS –...
- Page 8 OPERATION STEP 1 Use an appropriate tool like the Norfield Stylizer II to mortise the door for the Eurogroove. STEP 2 Place the fixture on the door with the End Stop against the end of the door. Ensure that the fixtures sit flat on the edge of the door with the alignment blocks fully inserted in the Eurogroove (Detail A in fig.
- Page 9 The Norfield MasterLine StrikeMaster (MFG600) can be used to make the mortise on the T-astragal before it is attached to the inactive door OR the Norfield MasterLine T- Master (MFG650) can be used to make the mortise on the t-astragal after it is attached to...