Advertisement
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away
.
from the drill when operating. Flammable waste, such as wiping or cleaning rags, must be placed in a closed metal container and
disposed of correctly.
DO NOT exceed the rated capacity of the drill.
DO NOT leave the drill operating unattended.
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT pull the plug from the power supply by the cable.
When not in use switch off the drill, remove plug from the power supply and do not leave until the drill has come to a complete stop.
3
2. INTRODUCTION
A comprehensive range of bench pillar drills for the professional workshop. Meets Safety of Machinery (Safety) Directives 1992
(and amendments). Models feature heavy-duty aluminium-bodied motors for long and reliable performance. Electrical circuitry protected with
no-volt release switch to prevent inadvertent start up and pulley cover protected by microswitch to prevent drill operating when cover is open.
PDM155B is fitted with an integral work light which illuminates the drilling table giving operator a clear view of the drilling process. All models
supplied with flip-up chuck guard. Large sized square tables fitted with precision rack and pinion height adjustment.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PDM125B . . . . . . . . . . . . . . . . . . . . . . PDM155B
Drilling Capacity (Chuck Size): . . . . . . . . . . . . . . . . . . 16mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mm
Spindle Nose Taper: . . . . . . . . . . . . . . . . . . . . . . . . . . MT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MT2
Swing: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403mm. . . . . . . . . . . . . . . . . . . . . . . . . . . .460mm
Spindle Centre to Column: . . . . . . . . . . . . . . . . . . . . . 165mm. . . . . . . . . . . . . . . . . . . . . . . . . . . .190mm
Spindle Travel:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80mm
Number of Speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Speed Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 190-3000rpm . . . . . . . . . . . . . . . . . . 190-3000rpm
Maximum Distance Spindle to Table: . . . . . . . . . . . . . 485mm. . . . . . . . . . . . . . . . . . . . . . . . . . . .475mm
Maximum Distance Spindle to Base:. . . . . . . . . . . . . . 700mm. . . . . . . . . . . . . . . . . . . . . . . . . . . .660mm
Working Table Surface Size: . . . . . . . . . . . . . . . . . . . . 254 x 254mm. . . . . . . . . . . . . . . . . .290 x 290mm
Working Base Surface Size: . . . . . . . . . . . . . . . . . . . . 205 x 200mm. . . . . . . . . . . . . . . . . .205 x 200mm
Overall Base Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450 x 270mm . . . . . . . . . . . . . . . . .495 x 290mm
Column Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80mm
Collar Diameter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55mm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60mm
Overall Height:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1050mm. . . . . . . . . . . . . . . . . . . . . . . . . .1050mm
Motor Power (Start): . . . . . . . . . . . . . . . . . . . . . . . . . . 370W (550W) . . . . . . . . . . . . . . . . 370W (550W)
Supply:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55kg
Noise Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76.9dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76.9dB
Noise Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89.1dB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89.1dB
Duty Cycle: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S2
Optional Keyless Chuck 16mm: . . . . . . . . . . . . . . . . . PDM/KC. . . . . . . . . . . . . . . . . . . . . . . . . .PDM/KC
Integral Work Light: (Bulb not included) . . . . . . . . . . . No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Yes
4. CONTENTS
4.1. Package contents Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to
your stockist immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket)) 3 Bolts and Washers (4)
3 Arbor
3 Wedge
5. ASSEMBLY
Note: Figures are illustrative and may differ in detail from your drill.
5.1.
Assembly
5.1.1. Place the column assembly on the base, align holes and secure with the bolts and washers provided.
5.1.2. Install table bracket onto column together with rack (fig.1), engaging gear in bracket with rack.
5.1.3. Install the rack collar and tighten firmly (fig.2).
5.1.4. Install the table adjusting handle (fig.2.A) and pivoted clamp bolt (the longer of the two - fig.2.B).
5.1.5. Tighten the handle set screw (with the hex. key provided) and the bracket clamp bolt.
5.1.6. Install the table and table clamp bolt (fig.3).
5.1.7. Carefully place the head assembly over the column and slide it into position. Align head with base.
5.1.8. Fit the two set screws in the side of the head and tighten with hex. key (fig.4) to lock head in position.
5.1.9. Fit the feed handle to the hub of the pinion shaft (align pin with slot) and retain with central screw.
5.1.10. To install chuck: open the chuck jaws completely by turning the chuck key anticlockwise. Place a piece of wood on the drill table
(to prevent the chuck from getting damaged).
5.1.11. Insert arbor (fig.5.B) into drill spindle (reduced diameter end first), fit chuck to protruding end of arbor and hold in place.
5.1.12. Turn feed handle to bring nose of chuck down onto wood (fig.5). Firmly pull on feed handle to seat arbor tapers in spindle and chuck.
5.1.13. Loosen clamp screw on safety guard mounting collar, pass guard up over chuck and fit collar round flange of quill shaft. Ensure guard
pivot is central and tighten clamp screw.
5.2.
Drill mounting
5.2.1. For stability and safety it is important that the drill base is securely bolted to the workbench.
5.2.2. Ensure that the mounting surface is capable of supporting the drill together with the weight of the heaviest likely workpiece.
© Jack Sealey Limited
3 Base
3 Feed Handle
3 Table
3 Set Screws (2)
3 Hex. Keys (2)
Original Language Version
3 Chuck and Key
3 Table Arm, Bracket & Worm (PDM260F - no arm)
3 Rack and Rack Ring
3 Safety Guard
fig. 1
PDM125B, PDM155B
Issue: 5 - 04/10/17
Advertisement
