Summary of Contents for Arachnid English Mark Darts 4500 Series
Page 1
SE W/ICE Page 1 SERVICE BULLETIN Concerning 4500 6000 Series English Mark Dart Games February 1987 WARNING--DISCONNECT ELECTRICAL POWER BEFORE ATTEMPTING SERVICE Due to an error in printed board circuit layout, there is a problem which may cause short life with the SC146D triac in both error causes...
Page 2
This modification should only be attempted by modification. qualified technicians. ARACHNID, INC. Gene Harlan Chief Engineer Fig. 1, Mica Insulator Fig. 3, 4500 Series After Modification Fig. 2, 4500 Series Before Modification...
2 S/8” x 9” and is bent into an “L” (the long direction) before inserting in the shadow box. part number from Arachnid for the foil is 13-0069. Although the short bulbs can be installed without moving the sockets down, the aluminum tape MUST bc used due to the increased heat of the shorter bulb.
Page 4
7. When servicing the game in the future, periodically check the placement of the tape, to be sure it has not shifted. If there are any questions regarding this or any other service problem, please call ARACHNID, INC. at 800-435-8319 (in Illinois; 815-654-0212). ARACHNID. Connie Reece Design Engineering Tech.
Page 5
SWITCH MATRIX TEST CHART remove the swkh from the switch matrix and transfers it to the main board. For troubleshooting purposes it is important to know which pins on the target interface board will give a particular score. Thii release. The LED flash should and the game...
Page 6
SUPER 6 PLUS II P 0 Box 2901 0 Rockford. IL 61132-290 (IL) 815/654-0212...
Page 7
Unplug the dart head pig- tails and remove it temporarily. Remove the following items (they are not reused): Web - (if an Arachnid Web Kit has been added.) Plexiglass Front Panel Power Supply...
Page 8
(See Figure 4) Pry off the side support blocks as shown in Figure 4. There is one block on each side. The front channel must have the glue and staples removed. It is a good idea to cut the staples flush on the inside. Trying to pull out staples may damage the appearance of the cabinet. SIDE SUPPORT FIGURE 4 BRACKET...
Page 9
(See Figure 8) Mount the front plastic panel as shown. underneath the component tray to attach to the coin door. With the tray positioned flush in the front and without a gap on the sides, open tray and drill thru the three 5116 dia. holes into the sup- port board (See Figure 4).
Page 10
STEP Remove backing on foil and place it above pilot holes in cabinet. Be careful not to cover lamp shield channels or the vent slot in the top panel, then screw down lamp socket. Repeat procedure for the other lamp assemblies. Drill (3) holes as close to the sides as possible and in the approximate location of the lamp sockets.
Page 11
TARGET INTER FACE FIGURE 15 RELOCATE LOCK, If there are any questions regarding these instructiol SPEAKER, AND please call Arachnid, Inc. at l-800-435-8319 NEW BRACE ON ATTACH (in Illinois 1-815-654-0212). OPPOSITE SIDE THE NOTCII WILT, HAVE TO BE ADDED TO SOME 5000’s.
Page 12
INSTALLATION INSTRUCTIONS FOR DOUBLE BULLSEYE - ALL GAMES Your Double Bullseye Accessory Kit should contain the following items: Inner Bull (Black) Outer Bull (Red) Decal (4. New Switch Matrix (Matrix is already installed on new double bull games) Carefully remove the dart head from your dart game by removing the 4 bolts holding the dart head in the game.
Page 13
“on” or “up” position. Figure 2 illustrates this. Install the decal strip in a convenient location above the competitor strip on the instruction panel. If you have any questions, please call Arachnid, Inc. at l-800-435-8319 (In Illinois l-815-654- 02 12). 2901 0 Rockford. IL 61 The Originator of ElectronicDarts ( I L ) 815/654-0212 .
Page 14
FIGURE 3 FIGURE 4 INSTRUCTIONS FOR 5000 S T E P 1 TURN THE GAME OFF AND UNPLUG FROM THE WALL OUTLET. UNLOCK AND REMOVE THE BACK DOOR FROM THE TOP CABINET. S T E P 2 (SEE FIGURE 1) FROM THE BACK SIDE OF THE GAME: (A) DISCONNECT THE PIGTAIL RIBBONS FROM THE TARGET INTERFACE BOARD.
Page 15
(FOR 6000 GAMES ONLY - SEE FIGURE 4) APPLY THE DECAL TO THE FRONT OF THE TOP CABINET. POSITION IT ALONG THE BOT- TOM, COVERING THE STRIPE AND THE “ARACHNID” NAME ON THE EXISTING DECAL. S T E P 5 (SEE FIGURE 5) (A) SCREW THE FOUR (l/4”...
INSTALLATION INSTRUCTIONS R ~DER'DART D ASSEMBLY) SUPE 6 2 0 0 6 3 0 0 G A M E M U S T B E A 6 2 0 0 O R 6 3 0 0 TO U P G R A D E T O T H E S U P E R S P I D E R ( M U S T C O N T A I N T H E C O I N PC B O A R D >...
Page 17
UPPER CABINET BOARD . MAIN (BACK VIEW> R E P L A C E S D I O D E N E T W O R K G R A Y CLIP---1 N E W T A R G E T I N T E R F A C E B O A R D E P R O M P / N 01-0188...
Page 18
If there are any problems regarding this or any other service problem, please call ARACHNID, INC. at 800-435-83 19 or in Illinois at 8 15-654-02 12. Arachnid, Inc. John Farmer...
Page 20
FROM THE BOTTOM OF THE POWER SUPPLY VIEW OF BOARD U S V E R S I O N CONNECT BLUE VIRE TO SVITCH QOT SIDE, YELLOV VIRES CPP. SIM T O FUSE CONNECT VH:li WCC FROM VIRE AT ‘TO R4’ T O TERH. CAP.
Page 21
V I E W O F B O A R D F R O M T H E B O T T O M OF T H E P O W E R S U P P L Y O V E R S E A S V E R S I O N B L U E VIRZ T O SVITCH W I T C H WOT rra,...