Related Manuals for Ruby 48bh 3SD
Summary of Contents for Ruby 48bh 3SD
- Page 1 48bh 3SD 01 2019 Use and maintenance Warning! Please read the instructions before use.
- Page 2 48bh TECHNICAL DESCRIPTION Cleaning width Squeegee width 2030 Working capacity, up to sqft/h 21.851 1 x 508 Brushes diameter 1 x 20 Brushes rpm Pressure on the brushes lbs. Brushes motor 18.5 Suction motor 18.8 mbar Suction vacuum water lift...
-
Page 3: Table Of Contents
INTRODUCTION Thank you for having chosen our machine. This floor cleaning machine is used for the industrial and civil cleaning and is able to clean any type of floor. During its advance movement, the combined action of the brush and the detergent solution removes the dirt which is aspirated through the rear suction assembly, giving a perfectly dry surface. -
Page 4: General Rules Of Safety
GENERAL RULES OF SAFETY GENERAL RULES OF THE BATTERIES The rules below have to be followed carefully in order to avoid injury to the operator and damage to the machine. − Read the labels carefully on the machine. Do not cover them for any reason and replace them immediately if damaged. -
Page 5: Legend Control Panel
LEGEND CONTROL PANEL DISPLAY BUTTON MAXIMUM SPEED REDUCTION BUTTON SUCTION MOTOR BUTTON SUCTION MOTOR SILENT MODE BUTTON BRUSHES-ON BUTTON AUTOMATIC BRUSHES UNLOCK BUTTON MAXIMUM SPEED INCREASE BUTTON DETERGENT SOLUTION ON/OFF BUTTON SOLENOID VALVE ON/OFF LEGEND MACHINE BRUSH BASE GROUP 11. SQUEEGEE LEVER DETERGENT SOLUTION TANK 12. -
Page 6: Display Reading
DISPLAY READING VISUALIZATION WHILE SWITCHING ON When the machine is switched on, the display shows the following screen which indicates the software release and the battery setting. BATTERY SETTING Setting batteries Setting batteries Setting for lead/acid SOFTWARE RELEASE batteries HOURMETER In the second screen the hourmeter is visualized. -
Page 7: Navigation Controls
NAVIGATION CONTROLS Scroll up Enter Increase Scroll down Decrease GENERAL SETTING To enter the menu for the setting, use the keyboard of the instrument board and proceed as follows: Keep the buttons (1) and (5) pressed simultaneously. Turn the key to switch on the machine. When “ID CHECK”... -
Page 8: Symbology On The Machine
SYMBOLOGY ON THE MACHINE Indication of the maximum temperature of the Symbol denoting the solution valve. solution detergent. Indicates the solution valve lever. It is placed near the charging hole of the solution tank. Symbol denoting the crossed bin. Indicates that at the end of its activity, the Symbol denoting the lifting of the squeegee. -
Page 9: Before Use
BEFORE USE ON-BOARD BATTERY CHARGER The machine is equipped with the on-board battery charger, please HANDLING THE PACKED MACHINE refer to the instructions of the constructor of this accessory what the The machine is supplied with suitable packing foreseen for fork lift charging operations concern. -
Page 10: Squeegee Assembly
ADJUSTMENT OF THE SQUEEGEE INCLINATION In case of need, to increase the rubber bending in the central part, it is necessary to tilt the squeegee rotating counterclockwise the Never leave batteries completely discharged even if the machine is register (6). To increase the rubber bending on the squeegee not used. -
Page 11: Recovery Tank
DETERGENT SOLUTION TANK energically the brush to push the button towards the coupling spring until it gets blocked. The figure shows the rotating sense for the brush coupling. The machine is equipped with a tank for the detergent solution. To load the detergent solution, take off the recovery tank and unscrew the cap (1). -
Page 12: Pre-Cleaning Operations
PRE-CLEANING OPERATIONS CONNECTION OF THE BATTERIES TO THE MACHINE Plug in the batteries connector (1) to the machine connector (2), A long usage of the machine with the empty detergent solution tank placed in the rear part of the machine might compromise the good operativity of the machine. -
Page 13: Working With The Manual Detergent Solution Adjustment
Acting upon the levers drive control (8) the machine starts to When the silent mode is on, the symbol on the display changes. move, the brush starts to rotate and the water begins to flow automatically. Releasing the drive control levers will stop the flow. During the first metres check that the squeegee adjustment guarantees a perfect drying action and that the detergent solution flow is appropriate. -
Page 14: Draining The Detergent Solution
DRAINING THE DETERGENT SOLUTION To drain the detergent left in the detergent tank: Take off the drain hose (1) from its support. Take off the cap (2). Collect the detergent solution on its proper bin. Do not mix different chemical detergent solutions. STOPPING THE MACHINE BY THE END OF THE WORK Before performing... -
Page 15: Daily Maintenance
DAILY MAINTENANCE RECOVERY TANK CLEANING Hold the exhaust hose placed in the front part of the machine. Take off the exhaust plug acting upon its lever and empty the recovery tank into appropriate containers (see under "OVERFLOW DEVICE"). Take off the suction cover (1) after rotating the blocking levers (2). -
Page 16: Weekly Maintenance
Wash the inside of the hose with a water jet, from the squeegee hose side. To reassemble the hose repeat reverse the operations above- mentioned. WEEKLY MAINTENANCE REAR SQUEEGEE RUBBER REPLACEMENT CLEANING OF WATER TANK AND FILTER Check the squeegee rubber wear and eventually turn or replace it. For the replacement it is necessary to: Bring the machine to an appropriate place for tanks draining. -
Page 17: Six-Monthly Maintenance
Replace the front rubber. To reassemble the squeegee repeat reverse the operations above- mentioned. Uncouple the hook (1) of the rubber holder blade, release the extremities (2) from the squeegee body and take off the rubber SIX-MONTHLY MAINTENANCE (4). SPLASH GUARD REPLACEMENT Unscrew the knobs in the rear part of the brush base group from the extremity of the metal strips. -
Page 18: The Brush Motor Does Not Work
Check that the battery connector is correctly plugged in. Act upon the levers drive control (3). If the problem persists, please contact the authorized technical assistance. THE MACHINE DOES NOT CLEAN PROPERLY The brush does not have the suitable bristle dimension: use only original brushes.
Need help?
Do you have a question about the 48bh 3SD and is the answer not in the manual?
Questions and answers