Advertisement
Children should be supervised at all times when the heater is in use.
Ensure that the heater is correctly turned off when not in use and store in a safe, dry area, out of reach of children.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of
experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Oil-filled radiators suitable for office, home, showroom and workshop use. manufactured to rigorous safety standards and fitted with a 13A BS
approved plug. Features full thermostatic heat control that cuts power to the heater elements when pre-set temperature is attained and tilt
safety switch. Elements designed to maximize area of the heated surface in order to transfer more heat to the atmosphere. Fitted with castors
for added mobility.
3. SPECIFICATION
mODEL
InPUT/OUTPUT
RD1500.V6
230V 13A 1500W
RD2500.V6
230V 13A 2500W
4. CONTENTS
Item
Description (RD1500.V6)
1
7 Element Oil Filled Radiator
2
Castor Wheel Plate
3
"U" Bolt
4
nut
5. ASSEMBLY
Refer to fig.2 and invert the radiator after removal from packaging, oil should be heard flowing internally under gravity, this is expected and not
a problem. Attach the castor wheels by passing the stud through the underside of the wheel plate and securing with the supplied nut. mount
the castor wheel plate between the first and second element of each end of the radiator. Tighten the wing nuts on the metal "U" bolts; return
the radiator to the upright position; oil should be heard flowing internally under gravity and your heater is ready to use when the flowing
ceases. Check the unit is the correct way up by observing carrier handle apertures are at the top and the cable tidy is at the bottom, also the
thermostat "LOW" and "HIGH" instruction is further confirmation (fig.3).
SAFETY FEATURE-: The tilt safety switch will isolate supply if accidentally tipped over or if assembled upside down.
6. OPERATION
6.1.
Unwrap the mains lead and plug it into the power supply.
6.2.
Turn the thermostat control to the highest setting.
6.3.
Choose the required heat output by selecting the appropriate switch which will light up when pressed.
6.4.
Low setting: . . . . . Select switch with one black bar above it.
medium setting: . . Select switch with two black bars above it. Set switch with one black bar to off.
High setting:. . . . . Select both switches.
6.5.
Once the required room temperature has been achieved turn the thermostat down until the light on the selected heat setting switch
goes out. The heater will then keep the surrounding air at the set temperature by switching on and off at intervals. You may reset the
thermostat at any time.
6.6.
To switch the unit off, turn the heat selecting switches off and unplug from the mains. Allow the unit to cool before handling or storage.
6.7.
Safety cut-out. The heater is fitted with a safety tilt switch and a thermostatic safety cut-out which will automatically turn the heater off
should it be placed in circumstances that cause overheating or malfunction. Should this happen, switch the heater off and disconnect
it from the mains. Allow the heater to cool before handling. DO NOT use the heater again until the cause has been identified and
remedied. If necessary return the heater to your Sealey dealer for servicing.
6.8.
When used for the first time set the heater to maximum power for a few minutes. Ventilate the room well to eliminate the newness
smell, typical of this type of heater.
© Jack Sealey Limited
nO OF ELEmEnTS
7
11
Qty
1
2
2
2
Original Language Version
Item
Description (RD2500.V6)
1
11 Element Oil Filled Radiator
2
Castor Wheel Plate
3
"U" Bolt
4
nut
fig.2
Qty
1
2
2
2
RD1500.V6, RD2500.V6
Issue: 4(I) - 10/06/14
Advertisement
