Download Print this page
Sealey GSS150819SL Instructions Manual
Sealey GSS150819SL Instructions Manual

Sealey GSS150819SL Instructions Manual

Galvanized steel shed 1.5 x 0.8 x 1.5m with sliding dr..

Advertisement

Quick Links

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when building this shed.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
Use appropriate safety clothing including eye protection.
Note! The assembly of this product will require assistance.
2. INTRODUCTION
Before commencing the assembly, we recommend that you read the instructions thoroughly. Your new shed
comes with all the holes pre drilled to make for fast easy assembly. We recommend that you assemble the
shed using a trestle table or sawhorses and planks. This will ensure that you are working off the ground and
make it easier for you. Assembly is a two person job and should not be attempted in windy conditions.
Sequence of operations.
2.1
Check all parts against the component list.
2.2
Assemble the rear wall panels.
2.3
Assemble the side wall panels.
2.4
Assemble the roof panels.
2.5
Assemble the front wall panels.
2.6
Assemble door.
2.7
Fit the panels together.
2.8
Prepare and fit to plinth slab.
© Jack Sealey Limited
INSTRUCTIONS FOR:
SHED 1.5 x 0.8 x 1.5m WITH SLIDING DR..
MODEL No:
Original Language Version
GALVANIZED STEEL
GSS150819SL
GSS150819SL
Issue: 1 - 30/08/12

Advertisement

loading

Summary of Contents for Sealey GSS150819SL

  • Page 1 GSS150819SL MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
  • Page 2 Check contents: Lay out all components with the part numbers facing upwards and check off against the parts lists on the next four pages. In the unlikely event of a missing component please contact you local Sealey dealer. © Jack Sealey Limited...
  • Page 3 1980 x 770 right sheet 1900-1980 x 770 left sheet 1980-1980 x 770 right sheet 1855 x 770 sheet 1900 x 735 sheet 1872 x 770 left © Jack Sealey Limited Original Language Version GSS150819SL Issue: 1 - 30/08/12...
  • Page 4 1460 top track 1460 Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...
  • Page 5 Staple Part No C4 Mid height wall bracket Part No 72 Please note some component descriptions may differ in manual text to listings, always use pictures from listings to double check component identity. ie M8 fixings may be supplied in lieu of 5/16”. Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...
  • Page 6: Parts Diagram

    6. PARTS DIAGRAM © Jack Sealey Limited Original Language Version GSS150819SL Issue: 1 - 24/08/12...
  • Page 7 7. ASSEMbLY ASSEMbLE THE REAR WALL PANELS 7.1.1 You will find it easier to assemble the shed using trestles, with timber studding of equal or greater panel length. Trestles are available separately from your Jack Sealey Dealership. Attach the studding to trestles with equal overhang using nylon cable ties or similar “safe” method. 7.1.2 Place panel 1R and 1L on your work table and join them together with the 10mm long self tapping screws.
  • Page 8 7.1.5 Fit item 31B the mid height wall channel to the panel and position it by the pre-punched holes and 10mm long self tapping screws. Note this channel is fitted with the flat face uppermost, ie. nearest the “top”, when the shed is assembled. 7.1.6 With 10mm long self tapping screws fix items 20B and 20C to top and bottom edges. Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...
  • Page 9 7.2.3 Fit item 32B the mid height wall channel to the panel and position it by the pre-punched holes and 10mm long self tapping screws. Note this channel is fitted with the flat face uppermost, ie. nearest the “top” when assembling the shed. 7.2.4 With self tapping screws fix item 21B to bottom edge, but do not screw fix item 21A to top edge at this stage. See those fixings marked with asterisk *. Original Language Version © Jack Sealey Limited GSS150819SL Issue: 1 - 30/08/12...
  • Page 10 7.3.3 Fit item 32C the mid height wall channel to the panel and position it by the pre-punched holes and 10mm long self tapping screws. Note this channel is fitted with the flat face uppermost, ie. nearest the “top” when assembling the shed. 7.3.4 With self tapping screws fix item 21B to bottom edge, but do not screw fix item 21A to top edge at this stage. See those fixings marked with asterisk *. Original Language Version © Jack Sealey Limited GSS150819SL Issue: 1 - 30/08/12...
  • Page 11 Place both panels item 3 on your work table and join them together with the 10mm long self tapping screws. See the pre-punched holes. 7.4.2 Fit top and bottom channels item 20A to panels by firstly sliding and finally tapping into place as previously explained in 7.1.3. Note that the smaller flange on the channels should always be adjacent to the outside face of the panel. The outside face is the top face in both diagrams. © Jack Sealey Limited Original Language Version GSS150819SL Issue: 1 - 30/08/12...
  • Page 12 7.4.3 Fit item 50 (angles) to each edge, refer to diagram above for flange orientation. Fix with 10mm long self tapping screws. GSS150819SL Issue: 1 - 30/08/12 Original Language Version © Jack Sealey Limited...
  • Page 13 Fit the top and bottom channels items 20J and 20K, inserting item 22E as illustrated. Pre-punched holes in items 11H and 22E for accurate alignment, see exploded ballooned details. Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...
  • Page 14 Fit the door way cover channels item 23H with 16mm long self tapping screws. See also section in 7.6 showing door 5A and orientation of frame and track. DO NOT screw fix in the positions indicated by the asterisk * at this stage. Original Language Version © Jack Sealey Limited GSS150819SL Issue: 1 - 30/08/12...
  • Page 15 INTRODUCTION OF PRE-ASSEMbLED DOOR (to front panel) 7.6.1 Slide the door into roller retaining tracks as indicated, before fitting hasp item C4. 7.6.2 Fit the hasp item C4 with 4mm diameter x 10mm long “pop” rivets into pre-punched holes. Section through track. “pop” Rivets Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...
  • Page 16 FITTING THE PRE-ASSEMbLED FRONT, REAR, END WALL AND ROOF PANELS 7.7.1 Self tapping screw fix the pre assembled end walls from 7.2 and 7.3 to rear wall from 7.1 followed by the front panel complete with door from 8.1. 7.7.2 Fit the staple supplied with hasp item C4 using 4mm diameter x 10mm long “pop” rivets. GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited Original Language Version...
  • Page 17 With the shed located centrally about the plinth slab, position the 6 anchor steel angles. M8 machine screw fix to internal compartment. This will require “spotting” and drilling 8mm diameter holes through to shed panels. Spot through holes to plinth slab, remove anchor angles and masonry drill slab for anchor bolts. NB! Anchor bolts and M8 machine screws are supplied, see “FITTINGS PACK”. 7.7.5 Insert anchor bolts, re-fit steel angles and anchor shed to plinth slab. 7.7.6 Self tapping screw fix the 2 mid height wall brace brackets item 72. © Jack Sealey Limited Original Language Version GSS150819SL Issue: 1 - 30/08/12...
  • Page 18 INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, 01284 703534 sales@sealey.co.uk IP32 7AR email Original Language Version GSS150819SL Issue: 1 - 30/08/12 © Jack Sealey Limited...