Advertisement
2. INTRODUCTION & SPECIFICATIONS
Modern design convector heaters with 3 heat settings of 750/1250/2000W for gradual control of heating elements. Rotary controlled room
thermostat maintains ambient temperature at pre-set level. Model No. CD2013TT features built-in turbo fan for accelerated heating and 24 hour
timer allowing the user to programme the time and duration the heater is operated. Both models have hard wearing feet to allow for maximum
stability. Slimline, sturdy construction and high quality finish make these units suitable for home, light industrial and office environments.
Supplied with 13Amp ASTA/BS approved non-rewirable plug.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CD2013 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD2013TT
Power Settings: . . . . . . . . . . . . . . . . . . . . . . . . .750/1250/2000W . . . . . . . . . . . . . . . . . . . . . . . . . 750/1250/2000W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V
Turbo Fan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Timer:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Size (WxDxH): . . . . . . . . . . . . . . . . . . . . . . . . . .600x100x350mm . . . . . . . . . . . . . . . . . . . . . . . . . 600x100x350mm
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.85kg. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5kg
3. ASSEMBLY
If the feet require fitting, align them as in fig.1
and secure by means of the self tapping screws
provided.
4. HEATER OPERATION
4.1.
Operating the heater.
4.2.
Place the heater in a suitable position in the area you require to heat.
Allow a minimum of 50cm between the heater and adjacent objects such as furniture etc.
4.3.
Plug the heater into the mains supply.
4.4.
Turn the thermostat knob (figs.2&3 C) to a high setting.
Selecting the heat output. (Refer to figs.2&3)
4.5.
Choose the required heat output by selecting the appropriate switch which will light up when pressed.
Low setting
Medium setting
High setting
4.6.
Using the thermostat.(figs. 2&3 C)
Once the required room temperature has been achieved, turn the thermostat down slowly in the direction of the min. setting until the
heat output switch light goes out. The heater will then keep the surrounding air at the set temperature by switching on and off at
intervals. You may reset the thermostat at any time.
4.7.
Turbo fan feature (CD2013TT only, fig.3).
To boost the output of air at any temperature setting select switch 'D' which has a fan symbol beside it. The fan can also be used to
circulate cool air only by switching off the two heat setting switches.
4.8.
Timer function (CD2013TT only, fig.3).
4.8.1. To activate timer function, turn the outer ring (fig.3.E) to the correct time. This will need to be repeated every time that the heater is
reconnected to the power supply.
4.8.2. The function selector switch (fig.3.F) has three positions: Left............Heater on permanently.
4.8.3. To select the time during which the heater is active, move the timer pins (fig.3.G.) outwards for the period required . Each pin is equal to
15minutes.
4.9.
To switch the unit off, turn the heat selecting switches off and unplug from the mains. Allow the unit to cool before handling or storage.
WARNING! DO NOT touch the top of the heater when in use as it becomes hot.
4.10. Safety cut out feature.
The heater is fitted with a thermostatic safety cut out which will turn the heater off automatically should should the airflow become
blocked or if the heater has a technical malfunction. Should this happen, switch the heater off and unplug it from the mains power
supply.
WARNING! In such a case the heater will be very hot.
DO NOT connect the heater to the power supply again until the reason the safety cutout activated has been identified. Allow the heater
to cool completely before handling and then check the air inlet and outlet for obstructions before attempting to switch the unit back on.
If the cause is not obvious return the heater to your local Sealey dealer for servicing.
© Jack Sealey Limited
fig.1
(750W)
Select switch 'A'
(1250W)
Select switch 'B'
(2000W)
Select both switches.
Original Language Version
fig.2
CD2013
Centre........ H eater timed.
Right..........Heater off. The heater will not operate at all with the switch set
in this position.
fig.3
CD2013TT
CD2013, CD2013TT
Issue: 1 -18/04/13
Advertisement
