Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ELBRO ST-SK1
Summary of Contents for ELBRO ST-SK1
- Page 1 I N S T A L L A T I O N M A N U A L ST-SK1 Alarm Security System™...
- Page 2 2 x 800mAh lithium batteries included (8h battery life in standby mode) Disarm Speci ications Clear Product name Alarm current ST-SK1 300mA Control Panel Layout (Back) Backup batteries ST-SK1 Lithium Batteries: 3.7V / 800 mAh x 2 (BL-5B) (8h battery life in standby mode)
- Page 3 Mount the Control Panel Quick Start-up Guide Before mounting the control panel on the wall, make sure the reception of the GSM signal is sufficient. Connect your System Fix the wall-mounting bracket on the wall with screws. Wedge the panel on the bracket, make sure they fit well. Using the GSM transmitter (SIM card) Basic Operations Open the battery compartment at the back of the control panel and insert a SIM card in the...
- Page 4 Speed Dial Setup from the control panel Press the Call button “ ” on the control panel for 3 seconds: the panel auto-dials the first The SS1 must be set up before using for the first time. During the setup of the system, the control stored phone number.
- Page 5 Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments Select the phone or SMS number you want to edit, type in the phone number and confirm with the key "Enter". Phone [1~5] is: Phone numbers Use the key "...
- Page 6 Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments Note System Setting Date and Time YYYY-MM-DD TIME (e.g. 2014-06-20 14H30) Date Format System Setting The entry and exit delays only work This function can be used if you do not want to bring a remote con- for sensors connected as Delay Zone Entry Delay 000-300...
- Page 7 Main Menu Sub Menu 1 Sub Menu 2 Sub Menu 3 Comments Note Enter the value (from 1 to 9) and confirm with "Enter". System Settings Ring Times <1-9>: 5 This function enables you to determine the number of times the control panel will ring before taking your call (for control by phone call).
- Page 8 Note Zone setup of accessories The call will end automatically if you do not send any command within 30 seconds. Table of commands for control by phone call Every detector can be assigned to 4 different categories of zones: Home Zone, Delay Zone, Normal Zone and 24-H Zone. To assign a detector to a zone, follow the instructions on page 8 of this Command Function Comment...
- Page 9 Disarm the System Settings Enquiry Setup by SMS Send: Send: IMPORANT: BEFORE USING FOR THE FIRST TIME Insert a SIM card in the control panel before starting SMS operations. Make sure the SIM card does not require any PIN code. SAVE A SMS NUMBER IN THE CONTROL PANEL (using the control panel). System disarmed.
- Page 10 Store Phone Numbers Rename Zones SMS Alert for Accessory Low Battery Store Phone Numbers for SMS Notifications (available for two-way acessories such as Motion Send: Send: Send "91~99". For example for zone 1, Detectors) send: For accessories assigned to zones that have been renamed, an SMS will be sent under the format “Zone name + low battery”.
- Page 11 Siren Volume and Ringing Time Rename RFID Tag Disarm Password Entry and Exit Delay Time Send: Send: Send: Send: Rename RFID tag names: Entry delay time(0-300sec):0 Siren volume(0=Mute,1=High):1 Disarm password (4 digits): Exit delay time(0-300sec):0 Siren ringing time(1-9min):3 1234 Copy, paste, then edit Copy, paste, then edit Copy, paste, then edit (case sensitive): (case sensitive): (case sensitive):...
- Page 12 Change System Language Restore System to Factory Settings by SMS Accessories Send: Send the code corresponding to the language you want to set. For example, Wireless Remote Control for English, send “0001”. 0000 Disarm 0001 LED indicator Home Mode Arm the system The settings will be restored to default values. Refer to the table below for the full list of Stored phone numbers...
- Page 13 Wireless Motion Detector Mute Mode Design Press the Home Mode button " " and then the Arm " " or Disarm " " button LED indications immediately after. Doing so, the control panel does not beep when you arm or disarm Blinks continuously: self-testing your system. Blinks once: an intruder is detected Blinks twice: self-testing is complete;...
- Page 14 Usage Testing A. After the installation, turn the detector on. After one minute of self-testing, press the test Open the case and remove the battery activation button, walk in the scope of detection and watch the LED indicator to make sure the detector strip.
- Page 15 Wireless Door / Window Contact Installation Features Open the case and remove the battery activation strip. This Door / Window Contact can be installed on doors, windows, and any other objects that Mount the sensor on the door and the magnet on the open and close. The sensor sends a signal to the control panel when the magnet is separated door frame.
- Page 16 RFID Tag Troubleshooting and maintenance Features The RFID tag enables you to disarm your system or unlock electronic door locks. Issue Cause of malfunction Solution Open the battery compartment and The control panel is switched off Register in the control panel turn the power on No response following interaction with the Refer to the instructions in the table page 8 of this manual (“RFID...
- Page 17 Precautions Standards For a safer use of the product and to optimize the lifespan of the product, we recommend you to follow the precautions below: This product bears the selective sorting symbol for waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European Directive The wireless accessories must be connected to the control panel.
- Page 18 ELBRO AG, Gewerbestrasse 4, CH-8162 Steinmaur, Switzerland www.elbro.com...
Need help?
Do you have a question about the ST-SK1 and is the answer not in the manual?
Questions and answers