Summary of Contents for Baby Love Ezy-combo
- Page 1 IMPORTANT: KEEP THIS BOOKLET IN THE PLACE PROVIDED ON THE CHILD RESTRAINT Harnessed Booster Seat INSTRUCTION BOOK Series No.: BL0090B-020133...
- Page 2 QUICK SETUP - HARNESSED CHILD Check/Adjust harness height Check/Adjust buckle height 25mm Pull Lift Shortest Length Mid Length Longest Length...
- Page 3 QUICK SETUP - HARNESSED CHILD Pull PUSH Attach Store Pull Click...
- Page 4 QUICK SETUP - WITH SEATBELT Check/Adjust buckle height Pull Lift Roll and store RH/LH Click To Shorten Shortest Length Mid Length Pull THIS ALWAYS SASH Longest GUIDE Length...
- Page 5 QUICK SETUP - WITH SEATBELT To Lengthen Pull Attach Store Pull Hook onto lap belt Use sash guide Use SecureGuard™ device...
- Page 6 INTRODUCTION To be used in a forward-facing position with built-in harness by a child whose shoulders are above the lower shoulder height marker (approximately 6 months of age) until their shoulders reach the middle shoulder height marker (approximately 4 years of age). Then to be used with a lap-sash seatbelt until the child’s shoulders reach the upper shoulder height marker (approximately 6 to 8 years of age).
- Page 7 INTRODUCTION Να χρησιμοποιείται σε θέση με κατεύθυνση προς τα εμπρός με ενσωματωμένο ιμάντα από ένα παιδί του οποίου οι ώμοι είναι πάνω από τον χαμηλότερο δείκτη ύψους ώμου (περίπου 6 μηνών) μέχρι οι ώμοι να φτάσουν στο μεσαίο δείκτη ύψους ώμου (περίπου 4 ετών). Στη...
- Page 8 INTRODUCTION Debe utilizarse orientado hacia adelante con un arnés incorporado para un niño cuyos hombros sobrepasen el marcador inferior de la altura de los hombros (aproximadamente a los 6 meses de edad) hasta que sus hombros alcancen el marcador medio de la altura de los hombros (aproximadamente a los 4 años de edad).
- Page 9 INTRODUCTION Magagamit lamang sa isang nakaharap pasulong na posisyon na may kasamang guwarnisyon ng isang bata na ang mga balikat ay lampas sa ibabang marka ng taas ng balikat (humigit-kumulang 6 na buwang edad) hanggang sa maabot ng kanilang mga balikat ang gitnang marka ng taas sa balikat (humigit-kumulang 4 na taong gulang).
- Page 10 INTRODUCTION Carefully read all the instructions for installation in this book. If in doubt about the method of installation, consult Babylove or agent or a child restraint fitting station authorized by a relevant transport authority or, in New Zealand, the agent for the vehicle or authorized child restraint fitter. THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT UPPER ANCHORAGE POINT IN THE CAR.
- Page 11 INDEX INTRODUCTION WARNINGS SHOULDER HEIGHT MARKERS - A GROWING CHILD - THE NEXT STEP TODDLER USE (WITH IN-BUILT HARNESS) FEATURES SUITABLE FOR USE HOW TO SETUP HOW TO INSTALL HOW TO USE HOW TO REMOVE CHILD USE (BOOSTER MODE WITH SEATBELT) FEATURES SUITABLE FOR USE HOW TO SETUP...
- Page 12 WHEN USED WITH THE 'BUILT-IN' HARNESS • Fit the restraint firmly to the car seat. • Fit the harness firmly to the child. • A loose restraint or harness is dangerous. • When used in this mode the restraint must be fitted to the car with a lap or lap-sash seatbelt. AS A BOOSTER SEAT (with or without a separately supplied Child Harness) •...
- Page 13 IMPORTANT : • Regularly check the restraint components, straps and other fitments for correct function and condition. Seek prompt repair. • IF AN AIRBAG IS FITTED IN THE SEATING POSITION WHERE THE CHILD RESTRAINT IS TO BE FITTED, FOLLOW THE VEHICLE MANUFACTURERS WARNINGS AND INSTRUCTIONS. •...
-
Page 14: Shoulder Height Marker
SHOULDER HEIGHT MARKER IMPORTANT: Follow this advice. Marker A Smaller Toddler - LOWER SHOULDER HEIGHT MARKER Using the in-built harness, the child’s shoulders must be in-line with this marker or above this marker. If the child’s shoulders are below then the child should remain in their previous child restraint. -
Page 15: Shoulder Height Markers & A Growing Child
SHOULDER HEIGHT MARKERS & A GROWING CHILD Marker C Marker B Marker A YOUNG TODDLER OLDER TODDLER Shoulders must not be below the lowest marker. When shoulders are in-line with middle marker, Use the in-built harness. Change to Booster Seat mode. From approximately 6 months of age. - Page 16 SHOULDER HEIGHT MARKERS & A GROWING CHILD OLDER CHILD AS A BOOSTER SEAT WITH AS A BOOSTER SEAT WITH LAP SASH SEATBELT CHILD HARNESS AND SEATBELT To approximately 6 - 8 years of age. To approximately 6 - 8 years of age. Shoulders above middle marker but below upper shoulder height marker.
- Page 17 SHOULDER HEIGHT LABELS & THE NEXT STEP Next type of restraint that can be used in the car for your child. When your child has outgrown the seat, you can then either use: Use a booster seat suitable for children up to 8-10 years of age and a Child Harness suitable for use with the booster seat.
- Page 18 FEATURES TODDLER USE Harness Tongues Harness Buckle 1. Padded cover for comfort 6. Cup Holder (if fitted) 2. Harness Slots (Toddler Mode) 7. Harness Adjuster Strap 3. Padded Insert (if fitted) 8. Harness Adjustment Lever 4. Shoulder Pads (if fitted) 9.
- Page 19 FEATURES TODDLER USE 15 16 Front of Vehicle 11. Vehicle Lap-sash seatbelt FORWARD FACING BELT PATH 12. Yellow labels 13. Attachment Clip 14. Car's Upper Anchorage Fitting 15. Top Tether Strap Adjuster 16. Top Tether Strap. 17. Top Tether Storage Pocket (attached to cover) 18.
-
Page 20: Suitable For Use
SUITABLE FOR USE TODDLER USE For a toddler whose shoulders are above the lower shoulder height marker, use with the integrated harness (from approx 6 months of age). Continue to use this child restraint with harness until the shoulders reach the middle shoulder height marker. Children are at risk of serious injury if they move to booster seats too early. -
Page 21: How To Set Up
HOW TO SETUP TODDLER USE ADJUSTING SHOULDER HARNESS STRAPS HEIGHT Correct fitment of the harness is very important as it restrains the child in the restraint. The harness must fit firmly around the upper torso of the child and be positioned so as to leave the child’s arms and legs free. Adjust the shoulder straps so that they are just above the shoulders. - Page 22 HOW TO SETUP TODDLER USE SETTING UP THE HARNESS A. Position the restraint on flat ground, supported from behind so that it will not tip over. B. Sit the child comfortably in position. C. Determine the desired shoulder strap position. D.
- Page 23 HOW TO SETUP TODDLER USE STEPS IN CHANGING SHOULDER STRAP SLOTS A. Disengage harness buckle. Fully lengthen the harness by pressing the Harness Adjustment lever and pulling the harness Pull shoulder straps. B. At the rear of the restraint, remove one of the harness shoulder straps from metal strap connector (shown) by slipping strap Lift through open slot.
- Page 24 HOW TO SETUP TODDLER USE ADJUSTING THE CROTCH BUCKLE HEIGHT Buckle height adjustment is changed by threading the anchor plates into the respective slot as shown below. The centre of the buckle should be positioned approximately in line with top of the thighs. The seat has the crotch straps fitted in the longest position when supplied, these may be adjusted to suit your child if necessary.
-
Page 25: How To Install
HOW TO INSTALL TODDLER USE INSTALLING INTO VEHICLE (FORWARD-FACING) (UPRIGHT OR RECLINED) Determine whether an upright or reclined installation is preferred as shown below. A. For upright mode, rotate the foot backwards until it clicks into position. B. For reclined mode, rotate the recline foot forwards until it is under the restraint.. - Page 26 HOW TO INSTALL TODDLER USE C. Position restraint centrally to the chosen vehicle seat position and forward facing. Some vehicle seat fabrics (particularly velours) may be damaged by a child restraint used continuously. We recommend the use of a Messy Mat (if supplied) or other protection under and behind the seat to keep the vehicle seat in good condition.
- Page 27 HOW TO INSTALL TODDLER USE D. Push down on the restraint to compress it into the vehicle seat. Whilst compressed in the seat, pull on the lap portion Pull to remove all slack from the belt. Pull the sash belt and allow excess belt to feed back into the retractor.
- Page 28 HOW TO INSTALL TODDLER USE G. Tighten adjustable top tether strap by pulling adjustment strap to remove slack as shown below, but do not over- tighten causing the restraint base to lift off the vehicle seat. H. Fold up excess strap and use the top tether pocket to store excess strap behind seat in the pocket provided.
-
Page 29: How To Use
HOW TO USE TODDLER USE PLACING TODDLER IN THE RESTRAINT A. Ensure the shoulder straps are adjusted to the correct height for your child (see page 21). Loosen shoulder straps by lifting the harness Pull adjuster and pull both shoulder straps evenly. Pull out the desired amount of slack. - Page 30 HOW TO USE TODDLER USE C. Fit either harness tongue into the harness buckle followed Tongue by the other tongue. A click is heard when the last tongue is fully engaged. Should the second tongue not engage - press the red button and reinsert the tongues.
-
Page 31: How To Remove
HOW TO REMOVE TODDLER USE TO REMOVE CHILD FROM RESTRAINT Press the red harness buckle button, both harness tongues will be released. You may lengthen the harness by pressing the adjuster button or lifting the adjuster lever and pulling the shoulder straps. Move each shoulder strap to the child's side, remove the child. - Page 32 FEATURES BOOSTER MODE WITH SEATBELT 1. Child Harness Slots (Booster Mode) 7. Harness Adjuster Strap 2. Padded cover 8. Harness Adjustment Lever 3. Armrests 9. Harness Buckle BOOSTER SEATBELT PATH 4. Red labels 10. Shoulder Height Markers 5. Cup Holder (if fitted) 11.
- Page 33 FEATURES BOOSTER MODE WITH SEATBELT 16 17 Front of Vehicle 13. Vehicle Lap-sash seatbelt 14. Top Tether attachment clip and VERSATETHER™Catch 15. Car's Upper Anchorage Fitting 16. Top Tether Strap Adjuster 17. Top Tether Strap. 18. Top Tether Storage Pocket (attached to cover) 19.
- Page 34 SUITABLE FOR USE BOOSTER MODE WITH SEATBELT For a child whose shoulders have reached the middle shoulder have reached the middle shoulder height marker (approx 4 yrs old), convert the seat to booster mode. Use as a booster seat with the vehicle seatbelt or a child harness approved for use with this child restraint until your child's shoulders reach the upper shoulder height marker.
- Page 35 HOW TO SETUP BOOSTER MODE WITH SEATBELT CONVERTING THE TODDLER RESTRAINT Place rolled-up Harness strap and Harness Tongue in recess INTO BOOSTER MODE To use this child restraint as a booster seat the harness needs to be stored under the cover. Disengage and remove the seatbelt from the restraint.
- Page 36 HOW TO SETUP BOOSTER MODE WITH SEATBELT STORING THE HARNESS A. Disengage harness buckle. Fully lengthen the harness by pressing the Harness Adjustment lever and pulling Pull the harness shoulder straps. Lift B. At the rear of the restraint, remove both harness Strap Connector shoulder straps from metal strap connector (shown) by slipping strap through open slot.
- Page 37 HOW TO SETUP BOOSTER MODE WITH SEATBELT F. Remove SecureGuard™ device from storage recess and engage into harness buckle. G. Adjust the crotch strap length if necessary. See page 39. H. Replace cover and re-attach elastic loops at the front of the cover to the child seat.
- Page 38 HOW TO SETUP BOOSTER MODE WITH SEATBELT ADJUSTING THE SECUREGUARD™ DEVICE POSITION IMPORTANT: The SecureGuard™ device ensures that the child does not slump and ensures the lap belt is always positioned on the child’s hips and thighs. If the seatbelt rides up onto the stomach then a child can be seriously injured in a crash.
- Page 39 HOW TO SETUP BOOSTER MODE WITH SEATBELT ADJUSTING THE SECUREGUARD™ DEVICE BUCKLE HEIGHT Adjust the SecureGuard™ device height by re threading the anchor plates into other slots in the seat shell. The seat has the crotch straps fitted in the longest position when supplied. Adjust the height to position the lap strap on the hips and thighs.
- Page 40 HOW TO SETUP BOOSTER MODE WITH SEATBELT FOR USE WITH VEHICLE SEATBELT SETTING UP THE SASH GUIDE A. Determine the correct height for sash guide. B. Unhook the elastic loops at the top rear of the restraint, then pull the cover forward to reveal the sash guide which is attached to a strap at the back of the seat cover.
- Page 41 HOW TO SETUP BOOSTER MODE WITH SEATBELT D. The sash guide should be located just above To Lengthen the child's shoulders. The sash guide must be used to position the Hold the strap, sash portion of the lap-sash seatbelt across the rotate and pull child’s shoulders and chest.
- Page 42 HOW TO INSTALL BOOSTER MODE WITH SEATBELT INSTALLING INTO VEHICLE (FORWARD-FACING) (UPRIGHT OR RECLINED) Determine whether an upright or reclined installation is preferred as shown below. A. For upright mode, rotate the foot backwards until it clicks into position. B. For reclined mode, rotate the recline foot forwards until it is under the restraint..
- Page 43 HOW TO INSTALL BOOSTER MODE WITH SEATBELT D. Tighten adjustable top tether strap by pulling adjustment strap to remove slack as shown below, but do not over- tighten causing the restraint base to lift off the vehicle seat. E. Fold up excess strap and use the top tether pocket to store excess strap behind seat away from child's reach.
- Page 44 HOW TO INSTALL BOOSTER MODE WITH SEATBELT F. Sit the child on the seat. G. If the seatbelt buckle is adjustable, adjust the Red seatbelt buckle as low as possible away from the child. path labels H. Position the lap-sash belt over the child BOOSTER ensuring the lap portion is positioned on SEATBELT...
- Page 45 HOW TO INSTALL BOOSTER MODE WITH SEATBELT I. Place the sash belt across the child's chest and through the sash guide. The Sash Guide is used to position the sash portion of the lap-sash seatbelt across the child’s shoulders and chest. J.
- Page 46 HOW TO USE BOOSTER MODE WITH SEATBELT CHECKLIST - BOOSTER MODE SETUP Centre of button on buckle, level with top of thighs. Lap belt firmly on hips/thighs. SecureGuard™ device fitted to lap belt. All slack removed from crotch strap when buckle is in the correct position. Sash belt is fitted through sash guide Red seatbelt path labels BOOSTER SEATBELT PATH...
- Page 47 HOW TO USE BOOSTER MODE WITH SEATBELT TO STORE SASH GUIDE When sash guide is not in use, hook the sash guide at the back of the cover to the elastic loop. TO REMOVE CHILD Disengage seatbelt tongue and buckle, remove the lap portion of seatbelt from the SecureGuard™ device and remove belt from child.
- Page 48 CHILD HARNESS PREPARATION BOOSTER MODE WITH CHILD HARNESS INSTALLING SAFE-N-SOUND PROTECTA PLUS™CHILD HARNESS WITHOUT EXTENSION STRAP INTO VEHICLE Hook the Child Harness attachment clip (1) onto booster seat VERSATETHER™Catch (2A). Then hook booster seat attachment clip (2B) onto vehicle anchor fitting (3). Ensure that none of the straps are twisted or passing over any sharp edges.
- Page 49 CHILD HARNESS PREPARATION BOOSTER MODE WITH CHILD HARNESS INSTALLING SAFE-N-SOUND PROTECTA PLUS™ HARNESS WITH EXTENSION STRAP INTO VEHICLE An adjustable extension strap is supplied with the Child Harness. Hook the Safe-n-Sound Protecta PLUS™ Harness clip first onto the extension strap catch, then hook the extension strap clip onto the VERSATETHER™...
- Page 50 CHILD HARNESS PREPARATION BOOSTER MODE WITH CHILD HARNESS INSTALLING CHILD HARNESS INTO SEAT A. Lengthen the Child Harness using the adjuster under the cover (see the Child Harness instructions for the adjustment method). Press the Adjuster button (1) and pull the shoulder strap (2). Left hand Strap Cross Strap Attachment Clip...
- Page 51 CHILD HARNESS PREPARATION BOOSTER MODE WITH CHILD HARNESS C. Pull the left hand Harness Strap & Cross Strap back Hook the Attachment Clip through the opposite shoulder slot. Hook the Child onto VERSATETHER™ Harness Attachment Clip onto the VERSATETHER™ Catch. Catch and ensure that the straps are equal in length.
- Page 52 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS INSTALLATION METHOD If the seating position has a lap only seatbelt then no other vehicle seatbelt preparation is required. If the seating position has a lap-sash seatbelt then it MUST be converted into a lap belt by fitting a Gated 3 bar slide, see page 53.
- Page 53 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS CONVERTING A LAP-SASH SEATBELT FOR USE WITH THE CHILD HARNESS. With the booster seat installed in the vehicle, sit the child in the seat. Fit the vehicle lap sash belt into the vehicle buckle and position the lap strap over the child's hips and thighs.
- Page 54 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS FITTING THE GATED SLIDE TO THE LAP-SASH SEATBELT NOTE: TO ENSURE CORRECT CONVERSION OF LAP- SASH SEATBELT TO LAP SEATBELT FOLLOW THESE STEPS. Outer Inner Strap A. Hold the lap and sash straps together and fold as shown. Strap Faces Slide the inner strap into the Gated Slide followed by the...
- Page 55 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS D. Feed the straps through the gated slide to remove any slack. This has now converted the lap-sash seatbelt so it will act like a lap only seatbelt. Hollow side towards child E.
- Page 56 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS USING LAP ONLY SEATBELT OR CONVERTED LAP-SASH SEATBELT WITH THE CHILD HARNESS Install the Child Harness to the booster seat and anchorages as detailed previously (page 48-51). Install the booster seat into the vehicle. Ensure the top tether strap is attached to the vehicle upper anchorage and adjusted correctly.
- Page 57 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS USING THE CHILD HARNESS Connect the Harness to the VERSATETHER™ Catch on the booster seat detailed on page 48 to 49. A. With the child seated, place the Child Harness straps over each shoulder. B.
- Page 58 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS D. Hook the SecureGuard™ device over the lap belt and engage the vehicle seatbelt tongue to the buckle. Check and adjust the seatbelt to sit firmly but comfortably around the child's pelvis. The seatbelt buckle should be located just below the child's hip to Adjuster ensure a firm yet comfortable fit.
- Page 59 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS TO REMOVE CHILD FROM HARNESS Lift Child Harness strap AND SEAT over child’s head. I. Disengage seatbelt tongue from buckle, remove the lap belt from the SecureGuard™ device and remove from the Child Harness strap loops.
- Page 60 HOW TO INSTALL CHILD HARNESS BOOSTER MODE WITH CHILD HARNESS RESTORING THE RESTRAINT FOR TODDLER USE A. Completely remove the child harness and gated slide (if used) from the car seat. Remove the adjustable extension strap (if used) from the VERSATETHER™ catch.
-
Page 61: Care And Maintenance
CARE & MAINTENANCE CARE & MAINTENANCE REGULAR CARE OF THIS RESTRAINT: Please check the following items regularly to ensure the safety of your child: A. Check the webbing of the straps for fraying, B. Check there are no cracks in moulding, C. - Page 62 CARE & MAINTENANCE CARE & MAINTENANCE BUCKLE OPERATION To ensure the buckle remains operational, the inside of the buckle must be kept free of liquids, sand, dirt, fluff, food or similar substances. If the buckle is not operating or you do not hear a strong audible click when second tongue is inserted, the buckle needs to be washed or replaced.
- Page 63 CARE & MAINTENANCE CARE & MAINTENANCE TO CLEAN THE COVER The restraint has a flame retardant cover which is removable for cleaning. Cleaning instructions are on the care label attached to the cover. When washing cover, engage hook & loop strips together to eliminate other garments being caught. Ensure to keep strips free of lint to work effectively.
- Page 64 CARE & MAINTENANCE CARE & MAINTENANCE TO REMOVE COVER Follow the sequence below A to G (anti clockwise) to remove the cover. Strap Connector If the sash guide is in Booster Seat mode the sash guide can be left in place for washing. If Child Harness is fitted remove the Child Harness.
-
Page 65: Accessories & Features
ACCESSORIES & FEATURES CARE & MAINTENANCE REPLACE COVER To replace cover refit in reverse sequence G to A. • For the in-built harness or toddler mode, refit the harness through the same shoulder strap slots refer to pages 21 to 23 for harness adjustment and setup. •... - Page 66 ACCESSORIES & FEATURES CARE & MAINTENANCE Use of aftermarket accessories, that is, accessories not provided with this child restraint can reduce the safety of the child restraint and may cause injury or death. Always follow the instructions covering the use of accessories in these instructions or the instructions provided with the accessory.
- Page 67 ACCESSORIES & FEATURES CARE & MAINTENANCE CUP HOLDERS (IF SUPPLIED) The Booster Seat has the facility to fit a cup holder on either side of the seat. Fit the cup holder onto the seat to use. Ensure the cup holder and its contents can not be crushed by the car door.
- Page 68 ACCESSORIES & FEATURES CARE & MAINTENANCE MESSY MAT™ SEAT PROTECTOR (IF SUPPLIED) Short Messy Mat™ Place ribbed or pocket end of the Messy Mat™ seat protector on edge of car seat, smooth back toward seat join (’A’) and fit in any excess Messy Mat™ into the join of the car seat (’A’).
- Page 69 INSTALLATION OF CAR UPPER ANCHORAGE FITTING CARE & MAINTENANCE Consult the vehicle owner’s handbook for location of anchorage fittings or anchorage points and the possible use of spacers. Some vehicles may have an anchor fitting fitted by the vehicle manufacturer. If anchorage points cannot be found refer to car manufacturer or local child restraint fitting station or traffic authority for preferred position of upper anchorage point.
- Page 70 INSTALLATION OF CAR UPPER ANCHORAGE FITTING CARE & MAINTENANCE Extension Strap distance to be measured. Length 300mm (Use BRITAX Safe-n-Sound part 0035). Length 600mm (Use BRITAX Safe-n-Sound part 0036). Available from all major child restraint retailers. Front of Vehicle Measure distance from restraint upper anchorage attachment clip to the car anchor fitting.
- Page 71 INSTALLATION OF CAR UPPER ANCHORAGE FITTING CARE & MAINTENANCE IF THE CAR IS FITTED WITH CHILD UPPER ANCHORAGE FITTING Fig.1. RESTRAINT UPPER ANCHORAGE POINT Attachment Bolt Locate the upper anchorage point behind the rear seating Lock washer position. (Consult the car owners handbook for the location of the upper anchorage point).
- Page 72 INSTALLATION OF CAR UPPER ANCHORAGE FITTING CARE & MAINTENANCE ONLY USE A 5/16 UNC GRADE 5 BOLT. IF THE BOLT IS NOT THE CORRECT LENGTH THE CAR MANUFACTURER’S HAND Note: Marking on the top of BOOK CAN PROVIDE ADVICE ON THE CORRECT LENGTH a Grade 5 Bolt.
-
Page 73: In Case Of Accident
IN CASE OF ACCIDENT If your restraint has been involved in a severe crash, you should destroy the restraint even if no damage is obvious. Some insurance companies offer vehicle insurance which covers or partially covers the replacement of your child restraint. Contact your insurance company for further details. Your insurance company may require you to keep the child restraint for assessment, but do not use the child restraint after a severe crash. - Page 74 NOTES...
- Page 75 NOTES...
- Page 76 WARRANTY Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonable foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be acceptable quality and the failure does not amount to a major failure.