Table of Contents
Advertisement
Quick Links
©2011 ClearSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 07.22.11
ClearSpan
Round Style Clear View Greenhouses
Photo may show a different but similar model.
CLEARSPAN
™
STK#
DIMENSIONS
106185
20' W x 10' 7" H x 20' L
106186
20' W x 10' 7" H x 24' L
106187
20' W x 10' 7" H x 36' L
106188
20' W x 10' 7" H x 48' L
GREENHOUSES
™
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ClearSpan 106186
Summary of Contents for ClearSpan 106186
- Page 1 Photo may show a different but similar model. STK# DIMENSIONS 106185 20' W x 10' 7" H x 20' L 106186 20' W x 10' 7" H x 24' L 106187 20' W x 10' 7" H x 36' L ©2011 ClearSpan™...
- Page 2 BEGIN TO ASSEMBLE THE SHELTER. • Identify whether underground cables and pipes are present before preparing the site or anchoring the Thank you for purchasing this ClearSpan™ greenhouse. structure. When properly assembled and maintained, this product will • Location should be away from structures that could provide years of reliable service.
- Page 3 A strut is typically secured to the frame work by special brackets and bolts. These words and phrases are common to most ClearSpan™ shelters and identify the different parts of • Swaged End or Swaged Pipe: The term “swaged'' the shelter.
- Page 4 CLEARSPAN GREENHOUSES ™ SPECIAL NOTE: Baseboards for Frame REQUIRED TOOLS These instructions describe installing a baseboard The following list identifies the main tools needed to (recommended) at ground level along each side of the assemble the shelter. Additional tools and supports may be frame.
- Page 5 CLEARSPAN GREENHOUSES ™ The following graphics and photos will help you identify the different parts. (Some parts are not shown.) FA4482B QH1402 Tek Screw Band Clamp (short) 102921 FAH320B & FALB32B FAH009B & FALB01B Neo-bonded Carriage Bolt & Hex Nut Carriage Bolt &...
- Page 6 CLEARSPAN GREENHOUSES ™ Round Style Clear View Greenhouse OVERVIEW This section describes assembling your Round Style Greenhouse. For details, please see section, Assembling the Round Style Greenhouse Components. See illustration ATTENTION: Position purlins evenly during the below to identify main parts of greenhouse.
- Page 7 CLEARSPAN GREENHOUSES ™ LAY OUT THE BUILDING SITE Use a transit or line level to drive the second corner post to the same depth as the first ground post. After the site is prepared, lay out the building site. String a line at least as long as the building from the Taking these steps before assembling the shelter saves first stake at 90°.
- Page 8 CLEARSPAN GREENHOUSES ™ ASSEMBLING THE ROUND STYLE GREENHOUSE Slide four (4) end purlin clamps (two on each side of FRAME COMPONENTS the peak) over the rafter pipes. After the site is prepared and an inventory of parts is complete, continue with the rafter assembly.
- Page 9 CLEARSPAN GREENHOUSES ™ RAFTER ASSEMBLY (continued) FRAME ASSEMBLY INTERIOR RAFTER ASSEMBLy After all ground posts are driven in place and rafters are assembled, assemble the frame. Complete the following steps for the interior rafters. Select the pipes for the first interior rafter assembly and NOTE: The baseboards (strongly recommended) shown in position these on the ground as shown.
- Page 10 CLEARSPAN GREENHOUSES ™ FRAME ASSEMBLY (continued) Secure the leg pipes to the ground posts using the 5/16" x 2 1/2" machine bolts and nuts. From the location marked in the previous step, measure forty-eight inches (48") and make another Rafter mark on the assembled purlin.
- Page 11 CLEARSPAN GREENHOUSES ™ FRAME ASSEMBLY (continued) Move to the interior rafter and align the mark on the purlin with the center of the rafter to maintain the proper As the second rafter is steadied, remove one section of rafter spacing.
- Page 12 CLEARSPAN GREENHOUSES ™ FRAME ASSEMBLY (continued) BASEBOARD INSTALLATION (RECOMMENDED) Secure each purlin pipe joint with a Tek screw. Gather the parts: Repeat the above steps as needed to stand and secure • Treated or recycled plastic lumber (supplied by the remaining interior rafters and purlins to complete customer).
- Page 13 CLEARSPAN GREENHOUSES ™ SIDE STRUT INSTALLATION Attach the remaining end of the strut to the baseboard using a lag screw or nut and bolt (not included). See There are four (4) side struts for the shelter. These struts the diagram that follows for location.
- Page 14 CLEARSPAN GREENHOUSES ™ END WALL INSTALLATION • DO NOT REPOSITION THE END WALL VERTICALS USED AT THE SEAM OF TWO (2) POLyCARBONATE The steps to install the end walls for the greenhouse PANELS. include the following: • Always consult the installation guides that shipped Install end wall framing.
- Page 15 CLEARSPAN GREENHOUSES ™ END WALL INSTALLATION (continued) Measure the distance between the top of the base tube and band clamp (Step 7) to determine the length of the Secure the base tube between the legs of the end first vertical section of the door frame tube.
- Page 16 CLEARSPAN GREENHOUSES ™ INSTALL THE END WALL FRAME (continued) Using a level (or other means), verify that one vertical door frame tube is plumb and tighten the band clamp Using the marks on the base tube for the rough bolt to lock the first door frame member in place.
- Page 17 CLEARSPAN GREENHOUSES ™ INSTALL THE END WALL FRAME (continued) With the square-to-round tube connect bracket attached to the top of the frame member, place a Use the end frame diagram to determine the number of square tube fitting on the bottom of the frame member.
- Page 18 CLEARSPAN GREENHOUSES ™ INSTALL THE END WALL FRAME (continued) Repeat the steps to attach the remaining roller assembly to the lower-right corner of the rough door Locate the 100356 lower roller assembly and remove opening. View as seen from outside the frame.
- Page 19 CLEARSPAN GREENHOUSES ™ END PANEL INSTALLATION Install a Tek screw and washer to hold the panel and foam seal in place. After the end wall framing is attached, the end wall panels are installed. ATTENTION: DO NOT install the screw near the top of the end panel where the next panel will overlap.
- Page 20 CLEARSPAN GREENHOUSES ™ END PANEL INSTALLATION (continued) The gray bars in the photo below represent the horizontal ribs of the corrugated panels. The dashed Choose the next 8' panel and overlap the top edge of line represents the edge of the roof panel that is the bottom panel with the bottom edge of the top panel.
- Page 21 CLEARSPAN GREENHOUSES ™ INSTALL THE CORRUGATED ROOF PANELS Place the panel at the desired height above the ground and on top of the end rafter. Align panel with the center The corrugated roof panels are attached to the tops of each of the rafter pipe and attach the panel to the top of the rafter using Tek screws and washers.
- Page 22 CLEARSPAN GREENHOUSES ™ INSTALL CORRUGATED ROOF PANELS (continued) Once the seams for the first run of roof panels are secured, install the next run of roof panels. EDGE OF ANy PANEL AT THIS TIME. THE NEXT SET OF PANELS WILL OVERLAP THIS EDGE BEFORE ATTENTION: These panels will overlap the edges yOU INSTALL SCREWS AND WASHERS.
- Page 23 CLEARSPAN GREENHOUSES ™ ASSEMBLE AND INSTALL SLIDING DOORS PREPARE THE DOOR FRAMES The general steps to install the door are as follows: Locate the two door frames (#102923) and the roller hardware kits for the top of the door frames.
- Page 24 CLEARSPAN GREENHOUSES ™ ASSEMBLE AND ATTACH SLIDING DOORS (continued) Adjust the flat plate and brackets to align the adjusting nut with the pre-drilled 1/2'' hole and tighten bolts. After the holes are drilled, temporarily insert the carriage bolts through the bracket and tube to hold the...
- Page 25 CLEARSPAN GREENHOUSES ™ ASSEMBLE AND ATTACH SLIDING DOORS (continued) Photo below shows the assembled doors and the corrugated polycarbonate panels. ASSEMBLE THE SLIDING DOOR After attaching the rollers to the top of the doors, install the corrugated polycarbonate panel on the doors using Tek screws (#FA4482) and washers (#102921).
- Page 26 CLEARSPAN GREENHOUSES ™ ASSEMBLE AND ATTACH SLIDING DOORS (continued) Repeat the steps to install the remaining sliding track mounting bolts. All mounting bolts must be installed at Verify that the marks for the sliding door track are level the same height on the end wall frame so that the track and attach the two sections of door track to the end is level.
- Page 27 For replacement or missing parts, call 1-800-245-9881 for assistance. Continue by reading the CARE AND MAINTENANCE information that follows. NOTE: With the exception of Truss Arch buildings, ClearSpan™ shelters and greenhouses do not have any tested loading criteria. Revision date: 07.22.11...
- Page 28 CLEARSPAN GREENHOUSES ™ 10'-10" Height QUICK START GUIDE 20' Round Style Greenhouse 20'-0" Width FRONT Grid Represents 12" Squares Ground Level Frame shown may differ in length from actual frame. Revision date: 07.22.11...
- Page 29 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 30 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 31 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 32 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 33 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 34 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 35 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 36 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 37 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 38 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 39 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 40 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
- Page 41 CLEARSPAN GREENHOUSES ™ Revision date: 07.22.11...
Need help?
Do you have a question about the 106186 and is the answer not in the manual?
Questions and answers