Page 1
LED Video Processor User Manual 说明书 △ Before using this LED Video processor please read this manual carefully and preserved for reference in the future. MAGNIMAGE LED-515D...
Page 2
Statements Without the written permission, any unit or individual could not copy, reproduction or translate the book or part of it. Also could not transmit it in any form or any way(electronic, mechanical, photocopying, record or other way) for any business and profitable purpose. The product specifications and information mentioned in this manual is just for reference, will not give prior notice if there is any updated.
Briefs Thanks for your purchasing our LED Video processor. Do hope you can enjoy the experience of the product performance. The design of the LED video processor conforms to international and industry standards. But if with improper operation, there will be a personal injury and property damage. In order to avoid the dangerous, please obey the relevant instructions when you install and operate the product.
Features Support user-defined output resolution, maximum horizontal 3840 pixel, and maximum vertical 1920 pixel. Quick switch for different input signal, 2 kinds of switch mode. Picture and text overlay, convenience to achieve the effect of the captions superposed and image compound. Operating mode can be restored soon, convenient for any apply ...
Using directions Included Accessories Using manual Power line DVI cable x 1 Disk 音频端子线 cable S-video cable Certificate of M3 screws ╳ 4 quality Sending card stud bolts 4pin2.54 sending card power cable...
Safety instructions Please use the correct power supply according that the power input voltage for this product range is 100~240V AC, 50/60Hz. When you need connect or pull out any signal or bound guideline. Please confirm that all the power supply cords have been pulled out ahead. When you need to add hardware device for the LED video processor, ...
Function introduction Brief LED-515D series products are the video processor developed for led display system, adopted the top image processing chips, internal 12 bits processing, with clearer images and richer colors. Advanced alternate motion picture processing technology, to remove video...
Using Menu LED-515D adopted a high brightness & contrast LCD screen to display the entire menu system, if the user does not have operation or operation overtime, the LCD screen will show the default state. Operate the menu system with the knob and button. The user can check and set its function and states convenient and intuitive to meet the demand.
CONTROL There are 4 buttons:PIP, PART, AUTO and OK key. The default menu system state Open close dual picture function, if long press button, change cascading relationship between picture 1 and picture 2 in the permission. PART Switch part and full AUTO Automatically rectify...
Default state introduction Turn on the power supply of LED-515, in the process of the system startup, the LCD front panel would display the start interface on the left screen, when the start completed, there will show the machine’s current state on the screen as the following figure shows: Above the figure, there are 4 lines content, explanation as the following: Lines...
Page 15
Form1:State icons and meanings Icons Area Name Hint(shortcut key in the bracket) Image freeze Image is frozen state PIP off PIP function off(PIP) PIP on [1] PIP function on,picture 1 is on the top(PIP) PIP on [2] PIP function on,picture 2 is on the top(PIP) Image intercepting Image intercepting1 function turn off(CROP)...
Main menu introduction The main menu will show the symbols listed in the table below, please check its specific meaning in the table below: main MENU, user "MENU", UP ” , “DOWN”,”LEFT”,”RIGHT”,”OK” six key to select and adjust the each item.
Main menu In the default state, press“UP”or "DOWN" to enter the main MENU state, the LCD screen will show the details as below: ► Image quality ► Output setting ► Audio setting ► Image crop ► Image switch ► Test picture ►...
Picture quality adjust sub menu Image mode standard Brightness Contrast Color Sharpness 3Ddenoise/VGA off/► Color temperature Normal rectify Scene mode norma Color temperature ► Green Gamma Blue VGA strengthen DVI enhance Image parameter ► reset...
Page 19
Image mode “user”,“vivid”,“soft”,“normal” Brightness Range 0~100. Range 0~100. Contrast Range 0~100. Color Range 0~24. Sharpness This function is valid when picture 1 is not VGA, divided into “Off” 、 3D de-noise “Adaptive” 、 “ Low” 、 “ Medium” 、 “ High” these five kinds of de-noise mode. VGA rectify It is effective when Picture 1 input port is VGA,automatically to rectify the position and size of input image, at this time, should ensure input image to...
Page 20
Output setting sub menu ► Output Resolution Output To H width 1024 V height 1024×768 60Hz H position Press OK To Conf V position Part and full Full Output LED-515Dsupport 19sorts of regular output resolution. Resolution find details in " output indicators"[ Minimum is 64, maximum is “the width of the current output resolution”...
Audio Input 3 Volume set is 50 (0---100) Default ON/OFF Mute Interface Interface matched with input signal LED-515D support 5 channel 2 audio input switching。One channel is HDMI, one is DP,other 3channel can be matched with AV1, AV2, VGA, DVI.
Reducing the above four parameters for the default state, that is the maximum value of picture width and height, starting for 0. LED-515D support double image intercepting function, it can simple double channel image fusion. Image intercepting function only can be used when input signal effective. The size of intercepting image will be limited within the size of input signal.
Picture switching sub menu Auto switch VGA1 1280╳1024 60Hz Switch mode Instant ━━━━━━━━━━ TAKE ► Picture switch 1920╳1080 60Hz Instant EFFECT Auto Auto switch function is closed. switch Picture If the picture 1 input signal effective, the picture 1 is on the top. priority Picture If the picture 2 input signal effective, the picture2 is on the top.
Test picture sub menu Test picture H location V location Test picture Range 0~72。0 means no test picture display,1~72 means test picture number. Open test picture, will close the picture 2 by force. If there is no signal for the picture 1 input port, it will be displayed for "Unavailable "...
Function setting sub menu Freeze ► Save Template Store ► Restore Template Template 1 Menu time-out Press OK to confirm HDMI Reproduce DVI Arbitrary mode rate Restore ► Factory Reset Template 1 Press OK to confirm conf Factory Reset Press OK To Conf Press Mu to Rtn Freeze Freeze functional switch, the picture display normal when it is closed, and...
Dual image sub menu Picture Text Overlay Source Preset mode user Transparency Translucent mode Mode 1 ► Text Overlay Transparency H width 1024 Above/Below Above V height And/Or H position Green V position Top display Picture 2 Dual Dual Pictures function“On”and“Off”. The default is Off.。 Pictures Input Switching input port of picture 2 (vice channel).
Time and task ► Time setting Date ► Task setting Time ► Arrange task Number Task number --/--/--/ Time Invalid character Switch input Operate Interface Time and task Time setting Set time and date Task setting 1 number ,set tack number,64 tasks can be set 2 time, time to do the task 3 character repeat everyday Do not repeat...
Menu language submenu Language select 中文/Chinese English/英文 the menu will display in Chinese 中文/Chinese the menu will display in English English/英文 Shortcuts menu LED-515 sets up total six input shortcuts (INPUTS), four function shortcuts (CONTROL), and two picture switch shortcuts (TRANSITION). Input shortcuts are:“AV1”,“AV2”...
Page 30
Function shortcut PIP function shortcut: Icon Explanation PIP function closed, channel 1 signal display normally. PIP function open, channel 1 is on top, namely channel 1 display area covers channel 2 image. PIP function open, channel 2 is on top, namely channel 2 display area covers channel 2 image.
Page 31
TAKE &EFFECT function shortcut: the menu In the “default state” [ 12], to press “TAKE” or “EFFECT” , will be fast picture switch interface as belows: VGA1 1280╳1024 60Hz ━━━━━━━━━━ TAKE 1920╳1080 60Hz Instant switch EFFECT Tips: 1. Before entering the interface, the system will prompt the user to force close all the confict function (automatic switch), and turn on the picture 2.
Input signal hot backup Summarize Note that what the input signal hot backup is? What is the use of it? In simple terms, warm backup is that when the input signal missed, using spare input signal automatically and rapidly to replace the original input signal, maximum ensure output image uninterrupted.
(around 0.2 seconds), backup channel image will be displayed, let picture interrupt time reduced to a minimum. LED-515D provides abundant function for the customers, some functions use requires users to have quite a bit of professional knowledge. When you...
Page 34
Phenomenon Check list Page Equipment without image, no Check the power cord display in the front panel. Check the power switch The front panel of the screen Check whether properly connected the input is displaying information, but signal and have switched to the corresponding no image output or output source (if no signal, the front panel LCD screen will...
Page 35
The warranty provisions 12 months warranty start from the day we make invoice to you; If you lost invoice, warranty will start from 60days after our production date. They are not include in our warranty The machine soaking and collisions produced besmirch or surface ...