Summary of Contents for Peachtree Woodworking Supply EZ SQUARE
- Page 1 EZ SQUARE BANDSAW FENCE Instructions Peachtree Woodworking Supply Inc. 6684 Jimmy Carter Blvd. Norcross GA 30071...
-
Page 2: Table Of Contents
The EZ SQUARE BAND SAW FENCE Table of Contents TABLE OF CONTENTS SAFETY GUIDELINES PARTS DIAGRAM ASSEMBLE THE FENCE CARRIAGE INSTALLING THE FENCE RAILS INSTALLING THE FENCE CARRIAGE MOUNTING THE FENCE TO CARRIAGE INSTALLING THE REAR FENCE BRACKET ADJUSTING FENCE PARALLELISM... -
Page 3: Safety Guidelines
WARRANTY Your EZ Square Band Saw Fence comes with a 30 day money back guarantee. If your are not completely satisfied, simply return it to us with the original packaging along with a copy of the receipt, and we will be happy to issue a refund for the purchase price paid. If you have any questions with the installation of your fence please call us at 770-458-5539. -
Page 4: Parts Diagram
Roller , Spring and Bolt 1/4” x 1” x 20 TPI Bolts 1/4” Nut 1/4” Lock Washer 1/4” x Flat Washer Slick Tape 1/4” x 1 3/4” x 20 TPI Locking Bar Guide Bolt Parts Diagram Peachtree Woodworking Supply, Inc. -
Page 5: Assemble The Fence Carriage
Fence Rails Page #5. Assembly Drawing Locking Knob Locking Bar Guide Bolt Threaded Hole 1/4” x 20 Nut Slick Tape Roller Spring 1/4” x 20 x 1 ½” Bolt Partially Threaded Bolt Fence Carriage Locking Bar Assemble The Carriage Peachtree Woodworking Supply, Inc. -
Page 6: Installing The Fence Rails
(Figure 2). If your edge of your table is thicker than 1/4” you may need to use longer mounting bolts. Note: The bolts must be left loose to allow for the Fence rails to slide on. Installing the Fence Rails Peachtree Woodworking Supply, Inc. - Page 7 Figure 5 Figure 4 The EZ Square Fence Rails can be adjusted together left to right to give more cutting width on either side of the blade (Figure 6 & 7) or separately to offset one rail to the other. (Figure 8) To adjust the rails, loosen the nut on both Fence Rail bolts just enough to move the fence.
-
Page 8: Installing The Fence Carriage
(Part #9), lock washers (Part #13), and 1/4” lock nuts (Part #12) heads up. Leave the lock nut loose enough so that the fence can be slid onto the bolts (about 3/8” of threads showing) Installing the Fence Carriage Peachtree Woodworking Supply, Inc. -
Page 9: Mounting The Fence To Carriage
Fence is even with the edge of the Fence Carriage. (Figure 14) Snug the four (4) bolts from the bottom so that Fence is just tight enough not to move on the Fence Carriage. You will tighten bolts fully after fence alignment. Figure 12 Figure 13 Figure 14 Mounting the Fence Peachtree Woodworking Supply, Inc. -
Page 10: Installing The Rear Fence Bracket
If the fence binds adjust the Rear Mounting Bracket (Part # 5) at the location of the bind and recheck the fence movement. Figure 17 Band Saw Top Tighten Rear Mounting Bracket hear. Fence Roller Assembly FlatEdge Installing the Rear Fence Bracket Peachtree Woodworking Supply, Inc. -
Page 11: Adjusting Fence Parallelism
Check the fence movement right and left for smooth movement and adjust the rear Fence Mount Bracket as need. (see Installing The Rear Fence Bracket Page 8) Figure 18 Part #3 Square Fence Mounting Bolts (See Page 6) Adjusting Fence Parallelism Peachtree Woodworking Supply, Inc. -
Page 12: Adjusting Fence Vertical Square
Fence Mount Bracket as need. (see Installing The Rear Fence Bracket Page 8) Shim here with washer to tilt the fence forward. Shim here with washer to tilt the fence back. Figure 19 Adjusting Fence Vertical Square Peachtree Woodworking Supply, Inc.