Cobalt Digital Inc BLUE-HS User Manual

ADJUSTING THE FIT OF THE BLUETOOTH HEADSET
You can adjust the fit of the COBALT BLUE-HS headset to provide the best sound clarity and comfort.
The headset comes with two different sized soft gel ear tips (large and small,) and an optional ear hook.
You can chose which size ear tip to use, whether or not to use the ear hook, and which ear you prefer to
wear the headset on.
The headset comes with the large-sized soft gel ear bud installed but you can replace it with the
optional small ear bud. To change the ear bud:
1. Turn the ear tip to position N as shown in the diagram. When in this position, the ear bud can be
removed by pulling it out and away from the headset.
2. Choose which size ear bud you wish to use. Hold the ear bud in position N and then affix it on the
headset. Then, turn it to position R or L to lock it to the headset.
3. When using the headset, keep the ear bud in position R or L to prevent the ear bud from coming
detached.
The ear loop enhances the stability of the headphone. It was installed on the headphone. If you would
like to switch it to the other ear, then you can remove it from the headset by first removing the ear bud.
Once removed, you can turn it over to the other side, and re-install it on the headset.
3
Controls and Connection
CHARGING THE BLUETOOTH HEADSET
The COBALT BLUE-HS Bluetooth Headset has an internal
Lithium Ion rechargeable battery pack which must be
charged prior to operation and must be recharged
regularly. A fully charged battery will provide
approximately 4 to 12 hours (or more) of operation
before needing to be recharged. However, operating
time can vary depending on usage and the condition of
the battery pack. Recharge the battery regularly.
To charge the COBALT BLUE-HS Bluetooth Headset:
1. Ensure the Headset is turned off. To turn the headset
off hold the Multifunction Button + the Volume Down
button for three to four seconds.
2. Plug the supplied charge cable into the charge jack on
the COBALT BLUE-HS Bluetooth Headset. You will need to
remove the protective rubber cover that is inserted into the
charge jack of the headset. (To prevent dust and moisture from
damaging your headset, always ensure this cover is in place
when you are not charging the BLUE-HS.)
3. Plug the other end of the charge cable into a powered USB
connector, such as a USB 2.0 port on a PC or a USB charger.
(USB charger sold separately. Part number P-CHA-BT-USB)
4. Once the charging process has begun, the LED indicator on the
headset will show a constant red light. When the battery is done charging, the LED light will shut off.
5. Typical charge time is approximately two hours. Actual charge time will vary depending on several
factors including the battery's charge state, condition, and age.
6. Disconnect headset from the USB power source when charging is completed.
Charging Cautions:
- Do not use a charge cable or wall charger that appears to be damaged. (Example: frayed wires,
melted plastic, etc.)
- Do not tamper with or modify the COBALT BLUE-HS headset, charge cable, or charger.
- Always turn COBALT BLUE-HS Bluetooth Headset off when charging.
Removable Ear Hook
The ear loop enhances the stability of the
headset. It can be removed or adjusted to fit
either the left or right ear of the user.
Multifunction/PTT Button
Used to turn the Bluetooth headset on and to
place the headset into pairing mode. When the
headset is paired with a cellular phone, this
button acts as an answer/hang up button or as a
Push-to-Talk button when the headset is paired
with a PRYMEBLU radio adapter.
Status LED
The LED flashes messages that let
the user know the current status of
the PRYMEBLU Headset.
Microphone
This microphone picks up the user's
voice audio to send over- the-air.
Charge Port
This micro-USB jack is used
to connect the wall charger
to the headset. (wall charger
not included)
Soft Gel Ear Bud Earphone
Received calls are heard through the
headset's earphone. The Gel Ear Bud
helps the headset fit the user's ear for
best security and sound clarity.
Volume Up / Down Buttons
These buttons can be used to
set the volume level of the
headset.
2
USB charger sold separately.
Part number P-CHA-BT-USB
4