1. Manuals
  2. Brands
  3. Guo Ping Manuals
  4. Saw
  5. GB916
  6. Operating instructions manual

Guo Ping GB916 Operating Instructions Manual

Horizontal band saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HORIZONTAL BAND SAW
Study Carefully Before Operating
Cutting capacity
Blade size
Blade speeds
Motor
Machins dim.
weighy
Guo Ping General Machinery, ShanTou
GB916
• 9"
(230mm)-80mm X406mm
I" X0.032" X 119!"
(25mm
X
0.9mm
X
3035mm)
60HZ 82,132, 170,235FPM(25,40,51,71 MPM)
SOHZ 68,110,142, l 96FPM(20,33,43,59MPM)
I½ HP 60HZ 1725 RPM
SOHZ 1420 RPM
64" X30" (l625MMX760MM)
(N.W.) 285kgs(625 Lbs)
(G.W.)
320(704 Lbs)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB916 and is the answer not in the manual?

Questions and answers

Summary of Contents for Guo Ping GB916

  • Page 1 Blade size (25mm 0.9mm 3035mm) 60HZ 82,132, 170,235FPM(25,40,51,71 MPM) Blade speeds SOHZ 68,110,142, l 96FPM(20,33,43,59MPM) I½ HP 60HZ 1725 RPM Motor SOHZ 1420 RPM Machins dim. 64" X30" (l625MMX760MM) weighy (N.W.) 285kgs(625 Lbs) (G.W.) 320(704 Lbs) Guo Ping General Machinery, ShanTou...

  • Page 2: General Safety Information

    General Safety Information 1 . Read the Instruction manual before operating the machine. 2 . If you are not thoroughly familiar with the operation of horizontal band saws, obtain ad -vice from your supervisor, instructor or other qualified person. 3 . Remove tie, rings, watch and other jewelry, and roll up sleeves. 4.

  • Page 3: Blade Selection

    Blade Selection A. Never use a blade so soarse that less than 3 teeth are engaged in the workpiece at any time. (Too few teeth will cause teeth to strip out. B. Never use a blade finer than required to obtain a satisfactory surface finish or satisfacto -ry flatness.
  • Page 4 1---<ITb- 2 ...L 2-0 0--3 ® STOP SUITABLE FOR THE AREA IN CANADA & U.S.A Electricd Schematis for the UE-916(115V/230V Rewired 110V) CHANGE STEP: R ------.. CHANGE 115V PLUG TO 230V PLUG CHANGE FUSE AT THE CONTROL AC 115V/230V BOX FROM 11 SV TO 230V REANGE MAIN MOTOR WIRING...
  • Page 5 SUITABLE FOR THE AREA 1-dn>--2 STOP IN CANADA & U.S.A. Elect r icd Schemat i s for t he UE-916(220V/440V & 575V) IF YOU WANT TO CHANGE VOLTAGE, P LEASE ACCORLING THE FOLOWING DR AWING TO CHANGE. R--- Key-Sw AC 1<Zl Fig.4 3 P HASE (MEOTOR) CONNEC TION (0) �...
  • Page 6 2-00--3 1-<D7>--2 SUITABLE FOR THE AREA IN ® ® STOP AUST R A LI A, SOUTH AFRICA, SOUTH EAST ASIA AND EAST EUR OPE. Elect r i c d Schemati s for t he UE-916(440V/ 220V) IF Y OU W ANT TO CHANGE VOLTAGE, PLEASE ACCORLING THE FOLOWING DRAWING TO CHANGE.
  • Page 7 ..L SUITABLE FOR THE AREA 1---6TI>- 2 2-0 0-3 3-0�5 ® STOP IN U.S.A. & CENTRAUSOUTH El e ctri cd Schemati s for t he UE-916(220V/440V ) IF YOU W ANT TO CHANGE VOLTAGE, PLEASE A CCORLING THE FOLOWING DR AWING TO CHANGE. Fig.4 3 P HASE(MEOTOR) CONNECTION e �...

  • Page 8: Single Phase

    Single Phase Refer to the wire drawing inside the electrical box and above for proper motor and transformer connections, lead selection and wiring vonnections from the motor to the power source for the voltage you are using. Important: Immediately after wiring the machine, remover the drive belt, turn on the power and make sure the motor is running in the right direction (counter-clockwise when looking at the motor shaft.

  • Page 9: Starting And Stopping The Machine

    8 . Place the blade in place on the wheels (A) and through the upper blade guard. CB)Fig. 1. 9 . Work the blade all the way up between the blade guide bearings with the back of the blade against the back-up bearing, as shown in Fig.

  • Page 10: Adjusting Feed Rate

    1 . Disconnect machine from the power source. 2. Raise saw arm to its highest position and close cutting pressure comtrol valve to hold saw arm in place. Locate tracking adjustment plate on the ba -ck side of the driven blade wheel. 4.

  • Page 11: Adjusti Ng Blade Guide Brackets

    Adjusti ng Blade Guide Brackets The blade guides should be set as close to the vise jaws as possible. T he right blade guide bracket, is not adjustable and is set at the factory to clear the right hand viseJ aw. The left blade guide bracket can be moved to the left or right depending on the position of the left hand vise jaw.

  • Page 12: Vise Adjustment

    5. Tighten locking screws CC). Slide blade guides back into contact with blade and tighten screws 7 . Connect machine to the power source. Vise Adjustment To position the moveable vise jaw: 1 . Turn vise handwheel (A-Fig. 10) 1 /2 torn counter-clockwise.
  • Page 13 Changing Speeds For 916A Your machine is provided with four speeds. To change speeds, proceed as follows: 1 . Disconnect the machine from the power source. 2. Loosen wing nut (A), Fig. 12 and lift up and swing belt and pulley guard (B) to the side of the machine.

Table of Contents