Subscribe to Our Youtube Channel
Summary of Contents for Navico Network Expansion Port 2
- Page 1 Manual Network Expansion Port 2 NEP-2 English www.lowrance.com www.simrad-yachting.com Brands by Navico - Leader in Marine Electronics...
- Page 3 Disclaimer As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance.
- Page 4 Compliance Statements The NEP-2 complies with the following regulations: • FCC Part 15 • CE compliant per EN60945 • C - Tick For more information please refer to our websites: www.simrad-yachting.com and www.lowrance.com The equipment named in this declaration, is intended for use in international waters as well as coastal sea areas administered by countries of the E.U.
- Page 5 Industry Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Warranty The warranty card is supplied as a separate document. In case of any queries, refer to our websites: www.simrad-yachting.com and www.lowrance.com NEP-2 Installation Manual | 3...
-
Page 6: Table Of Contents
Contents Introduction ..........5 Parts List .............5 Required tools and supplies ......5 Installation ............ 6 Mounting location ..........6 Mounting the NEP-2 module ......7 Wiring the NEP-2 ........... 8 Power ............8 Ethernet ............ 10 Cables ............10 NEP-2 network connection example ....11 Trouble shooting .......... -
Page 7: Introduction
Introduction The NEP-2 module is a five port marine Ethernet switch designed for use with compatible Simrad and Lowrance Ethernet devices. It can be used to share sonar, radar weather information over the network. Lowrance HDS and Simrad NSE multi-functional displays are not designed to inter-operate and exchange data over the same network —even though they inter-operate using many of the same components. -
Page 8: Installation
Installation Mounting location When installing the expansion port you should consider the following: Ensure you have as much separation as possible • between different electrical equipment (see following diagram for minimum distance recommendations). The NEP-2 conforms to the appropriate • Electromagnetic Compatibility (EMC) standards but proper installation is required to get best use and performance from this product. -
Page 9: Mounting The Nep-2 Module
Mounting the NEP-2 module Preferably mount the NEP-2 on a horizontal surface to avoid water following the cable and entering the connectors. If mounted on a vertical surface, mount the unit so that cables exit sideways. If that is not feasable, create drip loops to prevent moisture entering the connectors. -
Page 10: Wiring The Nep-2
Wiring the NEP-2 Don’t do this Do this Don’t make sharp bends in Do make drip and service the cables. loops Don’t run cables in a way Do tie-wrap all cables to keep that allows water to flow them secure down into the connectors. - Page 11 Power cable Color Function Black Battery (-) 2 m (6.5 ft) Blue Yellow Power Ctrl Battery (+) 12-24 V DC Suggested configurations for power wiring: Black Yellow Fuse Blue (no connect) 12 - 24 V DC NSE/HDS NEP-2 Black Black Yellow Yellow Remote Power On Bus...
-
Page 12: Ethernet
Ethernet Ethernet connector Function When Ethernet ports are not in use, cover them with the supplied dust-caps to prevent corrosion. Cables Part number Description 000-0127-56 Adapter cable: Ethernet Yellow male to RJ45 female 2m (6.5 ft). 000-0127-51 Ethernet cable yellow 5 pin 2m (6.5 ft.). 000-0127-29 Ethernet cable yellow 5 pin 4.5m (15 ft.). -
Page 13: Nep-2 Network Connection Example
NEP-2 network connection example BR24 BSM-1/LBS-1 NSE/HDS NSE/HDS NEP-2 12-24V DC WM-2/LWX-1 (US only) Power NEP-2 Installation Manual | 11... -
Page 14: Trouble Shooting
Trouble shooting LED status Probable fault Recommended action POWER LED Green —solid No fault; normal power Safe to use function. Red —solid Possible internal fault See your dealer has occurred. Off — no No power Check power light control wire connections. -
Page 15: Specifications
Specifications Electrical Voltage input 9-32 V DC Power consumption 500mA max. Power consumption <1mA when OFF: Communication Ethernet 10/100 Base-TX Module dimension Size: Width: 203.8mm (8.0 inches) in- cluding base. Length: 194mm (7.6 inches) plus connectors. Height 57mm (2.2 inches). Weight: 0.9kg (2lbs) Environmental specifications... -
Page 16: Dimension Drawings
Dimension drawings mm (8.1") 206.6 mm (8.0") 203.8 mm (2.2") 14 | NEP-2 Installation Manual...
Need help?
Do you have a question about the Network Expansion Port 2 and is the answer not in the manual?
Questions and answers