Controlling A Tv With The Remote; Troubleshooting - Toshiba SD-4960SU Instruction Manual

Toshiba-SD-4960(gb) 5/19/04 10:50 AM

Controlling a TV with the Remote

The remote control can be compatible with various
brands of TV by setting their control codes. The
TOSHIBA code has initially been set to control
TOSHIBA TVs.
Setting Control Codes
1. Press TV to set the remote control operating your
TV.
2. While holding down PROG. button enter the two
diglts of your TV's brand code (listed right) using
number buttons.
3. Release PROG.
4. Point the remote control at your TV and use each
button listed below to make sure your TV is
operated correctly.
TV POWER To turn the TV on or off.
CH To select TV channels in the
upper or lower direction.
TV VOL. To adjust the sound level.
I.SELECT To select an external source
such as a VCR.
Number buttons To select TV channels.
When selecting channels 1 to
9, first enter 0 and then the
desired number.
100 To substitute for 100 channel
key.
DISPLAY To turn on or off TV's screen
display.
ENTER To use for the TV's ENTER
key.
Important Note
• Some TV's may not respond to all the operations
above, or may not be operated at all with this
remote control. In this case, operate your TV with
its own remote control.
• For some brands, several control codes (brand
codes) are allocated. Try each of them until the
buttons work on your TV.
• If you replace the remote control's batteries, set
the brand code again.
Page 34
Table of Brand Codes
BRAND CODE
TOSHIBA PROG + 01
RCA/GE PROG + 02
SONY PROG + 03
MITSUBISHI PROG + 04
JVC PROG + 05
HITACHI PROG + 06
PANASONIC A PROG + 07
SHARP NEW PROG + 08
SANYO PROG + 09
MAGNAVOX PROG + 10
GOLDSTAR NEW PROG + 11
SAMSUNG PROG + 12
SHARP OLD PROG + 13
ZENITH PROG + 14
PANASONIC B PROG + 15
PIONEER PROG + 16
ENG-34

Troubleshooting

Before requesting service (troubleshooting), please check the following.
Problem
• Check the batteries in the remote. They may need replacing.
No operations can be
• Operate the remote control at a distance of no more than 20 feet.
performed with remote.
• Operate the remote control within 30° angle on either side of the
remote control sensor.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
• Ensure that the disc is installed with the label side facing up.
Disc does not play.
• Check the region number of the DVD.
• 5.1 channel sound is reproduced only when the following condi-
5.1 channel sound is not
tions are met. :
being reproduced.
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the "Dolby 5.1 ch" mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
The icon appears on
1. The DVD's software restricts it.
screen.
2. The DVD's software doesn't support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You've requested a title or chapter number or search time that
is out of range.
Disc Menu doesn't appear.
• Check if the disc has a Menu.
Play mode differs from the
• Some of the functions selected in the Setup Menu may not work
Setup Menu selection.
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot
• The Screen Ratio is fixed on your DVD discs.
be changed.
No audio.
• Make sure you have selected the correct Digital Output in the
Audio Options Menu.
• Press power on from a cold start with no disc in the unit. Press the
The screen is blocked
STOP ( ) and PLAY (
panel for three seconds. The SELECT MENU LANGUAGE display
will appear. Select the number button of the desired language.
• Press power on from a cold start with no disc in the unit. Press the
Forgot password
STOP ( ) and PLAY (
panel for three seconds. The SELECT MENU LANGUAGE display
will appear. Select the number button of the desired language.
Press the SETUP select Setup, then press RIGHT or ENTER.
Press Up or Down to select Parental Setup. The Parental Setup is
now unlocked as indicated on the display. You can change your
password.
• Go to the contents and find the section of the instruction book that
If you experience other
contains the explanations regarding the current problem, and follow
problems.
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
ENG-35
Action
Page
P5
P7
P11
P29~30
P14
P27~33
P31
P29~30
) buttons simultaneously on the front
P31~32
) buttons simultaneously on the front
P32~33
-