CX420(MS-1453)Disassemble Guide 1、BATTERY PACK 1.1:Move the “Unlock’ button base on left picture shows; 1.2:Release the “Release” button and move the battery pack base on left picture. Component Battery Pack S9N-0362240-SB3...
Page 3
CX420(MS-1453)Disassemble Guide 2、BOTTOM DOOR ASSY 2.1:Remove the 3 screws (M2.5*5mm), then remove the Bottom door. Attention: the screw driver torque is: 2.0-2.5Kgf-cm Component Bottom door 307-452J213-F62 Screw E43-1255001-G68...
CX420(MS-1453)Disassemble Guide 3、HDD MODULE 3.1:Remove the 2 screws(M2*3mm); then remove the HDD DOOR. Attention: the screw driver torque: 1.2-1.5Kgf-cm Component HDD DOOR 307-452K214-F62 Screw E43-1203013-G68 3.2:Remove the HDD Module according to the direction as pic shows.
Page 5
CX420(MS-1453)Disassemble Guide 3、HDD MODULE 3.3:Remove the 4 screws (M3*4mm) that stabilize the bracket. Attention: the screw driver torque is 3.0-3.5Kgf-cm Component Screw E43-1304009-G68 3.4:Remove the HDD bracket. Component HDD Bracket 307-4520111-H76 HDD Module S71-2450504-T14...
CX420(MS-1453)Disassemble Guide 4、ODD MODULE 4.1:Remove the ODD Module according to the direction as pic shows. 4.2: Remove ODD Bezel as below . Component ODD Bezel 307-452F213-F62 4.3: Remove 2pcs (M2*3mm) Screws, Then remove ODD Bracket as below. Attention: the screw driver torque is 1.5-2.0Kgf-cm...
Page 7
CX420(MS-1453)Disassemble Guide 、 、 5、THERMAL-KIT DRAM 5.1:Remove the 4 screws(M2.5*5mm) and FAN cable, after that remove the Fansink. Attention:the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 Fansink E32-0800482-S69 5.2: Open the CPU Slot with Screw Driver, then remove CPU Module as below.
Page 8
CX420(MS-1453)Disassemble Guide 6、KEYBOARD 6.1:Before remove K/B, firstly remove the Middle Cover. Notice the rib on the cover. Component Hinge Cover 307-454E212-SE0 6.2:Remove the Keyboard. 6.3 : Firstly push connector according to the direction as pic shows; then remove the cable.
Page 9
CX420(MS-1453)Disassemble Guide 7、SEPARATE UPPER CASE AND LOWER CASE 7.1 : Remove the 1 screw (M2.5*5mm) that stabilize the hinge Cap, then remove Hinge cap. Attention: the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 7.2 : Remove the 4 screws (M2.5*7mm) that stabilize the LCD hinge.
Page 10
CX420(MS-1453)Disassemble Guide 7、SEPARATE UPPER CASE AND LOWER CASE 7.3:Remove the LVDS cable as pic shows: Camera 7.4:Remove the CMOS Camera cable. 7.5:Remove the Bluetooth, MIC, Speaker cable. Speaker...
Page 11
CX420(MS-1453)Disassemble Guide 7、SEPARATE UPPER CASE AND LOWER CASE 7.6:Remove 4 screws(M2.5*5mm) Attention: the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 7.7:Remove 6 screws(M2.5*5mm) Attention: the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 7.8:Remove the 3 screws (M2*3mm) Attention: the screw driver torque is 1.5-2.0Kgf-cm...
CX420(MS-1453)Disassemble Guide 8、LOWER CASE ASSY 8.1:Remove the 2 screws (M2.5*5mm) Attention: the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 8.2:Remove the main board from Lower case. Component Main Board 607-14531-03S 8.3 : Remove the 4 screws (M2*3mm), then remove the Speaker module from lower case.
CX420(MS-1453)Disassemble Guide 9、UPPER CASE ASSY 9.1:Remove the 2 magnet as left pic shows: Component Magnet E2M-4521011-SF7 9.2:Release the connector that stabilize the T/P cable, then remove the T/P module FFC according to direction of left pic shows; Component FFC Cable...
Page 14
CX420(MS-1453)Disassemble Guide 10、 LCD MODULE ASSY 10.1:Remove the 8 cover rubber. Component Rubber E2Y-6740611-Y40 10.2:Remove the 4screws (M2.5*5mm). When removing the LCD bezel, should begin from the two sides, then the upside to downside. Attention: the screw driver torque is 2.0-2.5Kgf-cm...
Page 15
CX420(MS-1453)Disassemble Guide 10、 LCD MODULE ASSY 10.3:Remove the 3 screws (M2.5*5mm); Remove the Left LCD hinge. Attention: the screw driver torque is 2.8-3.2Kgf-cm Component Screw E43-1255001-G68 Hinge L E2M-4520311-G60 10.4:Remove the 3 screws (M2.5*5mm); Remove the Right LCD hinge. Attention: the screw driver torque is 2.8-3.2Kgf-cm...
Page 16
CX420(MS-1453)Disassemble Guide 10、 LCD MODULE ASSY 10.5:Remove the 6 screws (M2.5*5mm) Attention: the screw driver torque is 2.0-2.5Kgf-cm Component Screw E43-1255001-G68 10.6:Remove the display module from LCD cover. 10.7:Remove the LVDS cable from display module. Component LVDS Cable K19-3017001-H39...
Page 17
CX420(MS-1453)Disassemble Guide 10、 LCD MODULE ASSY 10.8:Remove the 6 screws (M2*3mm) Attention: the screw driver torque is 1.5-2.0Kgf-cm Component Display Module S1J-442G002-A90 LCD BRACKET-L E2M-4520511-H76 LCD BRACKET-R E2M-4520411-H76 Screw E43-1203013-G68 10.9:Remove the 3 magnet on LCD cover; Component LCD Cover Magnet...
Page 18
CX420(MS-1453)Disassemble Guide 10、 LCD MODULE ASSY 10.11:Remove the MIC Module as left picture show. Component MIC Module S34-2100920-K03 10.12:Remove the WIRELESS board from LCD Cover. Component Wireless board 605-3870-010 Wireless cable K10-3010051-V03 LCD Cover 307-452A515-P89...
Page 19
CX420(MS-1453)Screws specification Photo Screw specification Label (M2.5*L5MM) black (M2.5*L7MM) black (M2*L3MM) black...
Page 20
CX420(MS-1453)screws specification ■ 1、BOTTOM DOOR ASSY total 15pcs screws specification: Photo Screw specification label (M2*L3MM) black (M2.5*L5mm) black...