Page 1
Assembly Instruction JumpXfun Bungee Trampoline At www.jumpxfun.com you can find manuals in many languages and watch videos how to assemble and get the most out of your JumpXfun. Fit normal trampolines with a diameter between D300 to D480. Trampoline is not included in this unit. Model Number: JumpX40...
Page 2
Introduction Thank you for purchasing this JumpXfun Bungee Trampoline (JumpX). We hope that you will enjoy it. It will take a little time to assemble it. It is not unusual for you to take more than an hour to assemble this product; so please be patient and enjoy this process with a friend.
- Do not use JumpX after consuming alcohol, drugs, or narcotics. This seriously increases the risk of injury, as coordination ability, judgment, and reaction time are affected. Do not smoke while using JumpX. - Do not use JumpX if you are pregnant or suffer from high blood pressure. Consult with your doctor if you are in doubt about whether you should use JumpX.
Page 4
Keep this instruction manual - The harness and tubes must be taken indoors after use. Avoid sunlight. - Regularly check that components are securely tightened, since they may come loose over time. - Always inspect before each use for worn, abused, or missing parts. A number of conditions could arise that may increase your chances of getting injured.
Page 5
- Tip! The jumper can pull on the rubber tubes and use them to get started with the jump. Jumping instructions (video can be seen at www.JumpXfun.com) Always jump in the middle of the trampoline. Always jump straight up and down. Never jump from side to side.
Page 6
Parts list Parts No. Parts Description Quantity Corners Top inner tubes Top outer tubes Long tubes for legs Short tubes for legs Long Bolt Spring Washer Cap Nut Arc Washer Big U-Screw Small U-Screw Clamp Small Lock Nut Nut Cover Gap Spacer Long Rope (15 m) Short Rope (5 m)
Page 7
Parts No. Parts Description Quantity Swivel Reinforcing Steel Spacer Big Lock Nut Plastic feet Right plastic cover for winch Left Plastic cover for winch Protection Foam Wrench 13 mm Wrench 19 mm Wrench Rubber tube 20 kg Rubber tube 10 kg Harness Small Self-Locking Screw Allen Wrench...
Page 8
JumpX fits many different trampolines, so you will need to adjust it to fit your specific trampoline. STEP 1 The top frame must be adjusted to fit exactly to your trampoline. The legs of the JumpXfun should be right next to the legs of your trampoline, and as close to the legs as possible.
Page 9
STEP 2 The tubes must be pushed into each other so that the downward poles stick straight out of every leg on the trampoline, and as close to the trampoline’s legs as possible. The top frame should form a square. The top of JumpX must be adjusted so the legs of JumpX are as close to the legs of the trampoline as possible.
Page 11
STEP 4 Refer to the below diagrams to fix the Pulley block at the end of rope 17. The short rope (17) (5 metre) is used down to the winch, onto the Pulley block. 8. After cutting, treat the end of the rope with fire to prevent fraying.
Page 12
STEP 5 The long rope (16) (15 metre) is used at the top. Refer to the below diagrams to load the rope 16 into the pulley block.
Page 13
STEP 6 Refer to the below diagrams to fix the swivel at the end of rope 16. Adjust the length of the cord, to fit your trampoline. You must be able to lift the jumper all the way to the top, (22) all the way up to (19).
Page 17
STEP 10 STEP 11 Mount 8 pieces of foam (A) on the 4 long tubes and mount them under the 4 corners. Run the foam (A) down so it covers from the top edge of the trampoline and two metres up.
Page 18
STEP 12 The short tubes (5) must only be used if you have a trampoline with legs of 70-90 cm. If you have an in-ground trampoline, you must not use short tubes (5). Plastic feet (25) should be put under the short tubes (5). If you have an in-ground trampoline, the plastic feet should be put under the long tubes (4) (See step 10).
Page 19
STEP 13 Assembly of hand winch set. The winch must be mounted so the handle is on the right side. It should be mounted between the ground and the frame of the trampoline, so you can easily turn the handle. The cover must be put on, fasten it with screws.
Page 20
(when the trampoline is buried, the distance must be between the fittings should be minimum 20 cm.) When you have a trampoline with 3-5-7 legs, you can only attach the JumpXfun two legs to the trampoline's 2 legs, the other 2 to be mounted on the trampoline edge, with a double bracket.
Page 22
STEP 17 Refer to the below diagrams to fix the Harness. It can be dangerous not to raise the jumper all the way up, and not to have enough rubber tubes on it. here have to be so many rubber tubes on, so that the jumper cannot reach the trampoline's dew with its head.
Page 24
JumpX should be disassembled before moving it over longer distances. For shorter moves it should be lifted from the ground by 4 people and kept horizontal during transport. See more at www.JumpXfun.com This product is protected by Patent: PA 2016 70501 and PR 179187...
Need help?
Do you have a question about the JumpX40 and is the answer not in the manual?
Questions and answers