Programming The Remote Control For Use With A Vcr Or Cable Tv Converter; Vcr Code Table - Toshiba 32AX60 Owner's Manual

Programming the remote control for use
with a VCR or cable TV converter
The remote control provided with your Toshiba TV is preprogrammed
to operate Toshiba VCRs also.
To operate non-Toshiba components using
the remote control provided with your TV:
1. Refer to the VCR and cable TV converter code table below to
find the corresponding code for your VCR or cable TV converter
brand.
If more than one code is listed, try each one separately until you
find the one that works.
2. If you are reprogramming the remote control to operate your:
• VCR: Set the TV/CABLE/VCR switch on the remote control
to VCR.
• Cable TV converter: Set the TV/CABLE/VCR switch on the
remote control to CABLE.
3. Hold down the RECALL button while using the Channel
Number buttons to enter the three-digit code of your VCR or
cable TV converter brand.
4. Point the remote control at the VCR or converter and press
POWER to test the code.
• If the VCR or converter turns on, you have entered the
correct code.
• If the VCR or converter does not respond to the remote
control, you may have entered the incorrect code.
Repeat steps 1–4 using another code.
5. Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the codes you used:
VCR code _____________________
Cable TV converter code _____________________

VCR code table

Brand Code
Adventura 019
Aiko 297
Aiwa 019
Akai 060, 068, 080, 125,
261
American High 054
Asha 259
Audiovox 056
Beaumark 259
Bell & Howell 123
Brandt 206
Broksonic 140, 203, 230, 314,
380
Calix 056
Canon 054
Capehart 039
Carver 100
CCE 091, 297
Citizen 056, 297
Colt 091
Craig 056, 066, 091, 259
Curtis Mathes 054, 060, 079
Cybernex 259
Daewoo 039, 064, 297
Daytron 039
Dynatech 019
Electrohome 056
Electrophonic 056
Emerex 051
Emerson 019, 021, 056, 062,
080, 087, 140, 203,
227, 228, 230, 231,
297, 313, 314, 380,
498
8
POWER
LIGHT RECALL POWER
TV
Recall
MUTE TV/VIDEO TIMER
CABLE
VCR
TV/Cable/VCR
switch
2 3
1
CH
4 5 6
Channel
Number
7 8 9
VOL
CH RTN
100 0 ENT
ADV/
PIP CH
FAV
ENTER FAV
ADV/
PIP CH
STOP SOURCE PLAY PIP
Note:
• Every time you replace the batteries, you
will need to reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These
VCRs have a switch labeled "VCR1/VCR2. "
If your VCR has this kind of switch, it may
not respond to any of the codes for your
VCR brand. In this case, set the switch to
the other position (VCR1 or VCR2) and
reprogram the remote control.
Fisher 066, 073, 085, 123
Fuji 052, 054
Funai 019, 344
Garrard 019, 344
GE 054, 079, 084, 221
Go Video 251, 298
Goldstar 037, 056, 057
Gradiente 019
Harley Davidson 019
Harman/Kardon 057, 094
Harwood 087, 091
Headquarter 065
HI-Q 066
Hitachi 060, 061, 084, 124,
185, 254
Jensen 060
JVC 027, 060, 086
Kenwood 057, 060, 086