Subscribe to Our Youtube Channel
Summary of Contents for Lipco SF 50
- Page 1 Translation of the original Stump cutter SF 40/50 instructions LIPCO GmbH Am Fuchsgraben 5b D-77880 Sasbach Tel. +49 7841 6348-0 +49 7841 6348-300 E-mail mail@lipco.com www.lipco.com...
-
Page 2: Introduction
Instructions Stump cutter SF 40/50 Introduction Dear Customer, We thank you for having chosen a . We hope that you will be happy with your choice. In order that your will serve you well for many years, we ask you to pay close attention to the Instructions for Use and Maintenance which you will find in this manual. -
Page 3: Table Of Contents
Safety regulations Accident prevention Design features Technical Data Preparation 10. Connection to the engine-driven machine 11. Working with the LIPCO Stump cutter 12. Maintenance 13. Replacement if the cutting blaeds 14. After use 15. Notices 16. Guarantee 17. Declaration of conformity 3 - 24 150040-02-EN BA SF 40_50 / 22.03.2019... -
Page 4: Designated Use
Instructions Stump cutter SF 40/50 Designated use , when connected to single axle tractors / power mowers, is designed to remove tree stumps. Any other use for purposes other than those described here is considered contrary to the designated use. The manufacturer cannot be held liable for damage resulting from such use;... -
Page 5: Warning Signs Attached Tot He Machine
Instructions Stump cutter SF 40/50 Warning signs attached to the machine Before starting operation, the personnel must have read the operating and safety instructions and must observe them. Before commencing maintenance and repair work, switch off the engine and pull the key. With the drive switched on and the tractor engine running, maintain sufficient distance to rotating tools. - Page 6 Instructions Stump cutter SF 40/50 Wear foot protection. Do not reach into rotating tools. Machine parts should only be touched after they have come to a complete halt. 6 - 24 150040-02-EN BA SF 40_50 / 22.03.2019...
-
Page 7: Safety Regulations
Instructions Stump cutter SF 40/50 Safety regulations The operation of machines with rotating or moving tools always bears risks. Please always follow the safety regulations: • Before starting operation, the personnel must have read the operating and safety instructions and observe them. •... -
Page 8: Accident Prevention
Instructions Stump cutter SF 40/50 Accident prevention Most accidents that occur during work, maintenance or transport of a machine are due to non-observance of the most elementary rules of accident prevention. It is, therefore, necessary that all licensed users (relatives, employees, colleagues) read and observe the rules given below and written on the adhesive labels of the machine itself: •... - Page 9 Instructions Stump cutter SF 40/50 • During service or repair work, make sure that no one can start up the machine accidentally! • Do not, for any reason, climb onto the machine during operation. • Do not act with any objects on the machine during operation! •...
-
Page 10: Design Features
Instructions Stump cutter SF 40/50 Design features , when connected to any type of engine- driven machine from 7 kW, is capable of removing tree stumps. The main characteristics of the are its universal attachment to different engine-driven machines and its reduced machine width, offering the possibility of achieving optimum work results on narrow access roads and in very limited space. -
Page 11: Technical Data
Required drive Disc Ø Hard-metal (kg) power (cm) tools (pcs.) (KW) SF 40 SF 50 Main dimensions SF 40 1400 SF 50 1400 The speed of the engine-driven machine must be between 500 and 1000 rpm 11 - 24 150040-02-EN BA SF 40_50 / 22.03.2019... -
Page 12: Preparation
Instructions Stump cutter SF 40/50 Preparation • Important! Adjust balance between motor device and stump cutter before the start-up! In this adjustment, bearing arms of the support are extended shortened depending motorized device. To do so, the fixing screws (A) have to be removed and the internal tubes (B) to be pushed... -
Page 13: Connection To The Engine-Driven Machine
Instructions Stump cutter SF 40/50 10. Connection to the engine-driven machine Before attaching the machine flange (Fig. 3, Ref. A) corresponding to the type of engine-driven machine you have, it is recommended to spread grease on the outer diameter of the machine hub (Fig. 3, Ref. B). -
Page 14: Working With The Lipco Stump Cutter
Instructions Stump cutter SF 40/50 11. Working with the LIPCO Stump cutter Move the Stump Cutter to the tree stump to be cut. Position the unit such that the cutter disc is located centrally above the tree stump. Then wind the support wheel to the top position. Lift the machine via the pivoting device until reaching a distance above the ground of approx. - Page 15 Instructions Stump cutter SF 40/50 When working with a second person, the additional handle is clamped firmly on the machine. Now, the second person can assist the machine operator "from the front". Additional handle • Attention! Turn off the engine of the engine-driven machine before making any adjustments (e.g.
-
Page 16: Maintenance
Instructions Stump cutter SF 40/50 12. Maintenance Steps to be carried out in order to maintain the machine in good working condition: • Check the oil level in the Oil filler neck angular gear. (Fig. 4) In horizontal position the gear drive should be filled with gear oil to the lower edge of the filler... - Page 17 Instructions Stump cutter SF 40/50 • Check whether all screws, especially those of the cutting blades, are firmly tightened. Replace damaged screws immediately. (See chapter "11. Replacement of the cutting blades"). Note: Only use original screws. • Lubricate movable parts, e.g. pivoting device at the bearing points.
-
Page 18: Replacement If The Cutting Blaeds
Instructions Stump cutter SF 40/50 13. Replacement if the cutting blaeds When replacing the cutting blades, make sure that the machine is secured against unintentional tilting! When working with the unit lifted, always ensure mechanical protection by means of adequate supporting elements! When a cutting blade becomes broken, immediately stop work and replace the damaged parts. -
Page 19: After Use
Instructions Stump cutter SF 40/50 14. After use If the is to remain unused for a longer period, it is necessary to carry out the following steps: • Thoroughly wash and dry the • Check the function of all movable parts and lubricate them! Replace damaged or worn parts! •... -
Page 20: Notices
Instructions Stump cutter SF 40/50 15. Notices 20 - 24 150040-02-EN BA SF 40_50 / 22.03.2019... - Page 21 Instructions Stump cutter SF 40/50 21 - 24 150040-02-EN BA SF 40_50 / 22.03.2019...
-
Page 22: Guarantee
Instructions Stump cutter SF 40/50 16. Guarantee For more details please refer to: https://www.lipco.com/en/downloads/ 22 - 24 150040-02-EN BA SF 40_50 / 22.03.2019... -
Page 23: Declaration Of Conformity
+49 172 7694 903 +49 7841 6348-300 E-Mail mail@lipco.com E-Mail mail@bauer-ib.com http://www.lipco.com Denomination: LIPCO stump cutter SF 40/50 Serial no: Year of manufacture: The manufacturer declares expressly, that the machinery fulfills all the relevant provisions of the • Directive 2006/42/EC... - Page 24 24 - 24 Design: mail@bauer-ib.com...
Need help?
Do you have a question about the SF 50 and is the answer not in the manual?
Questions and answers