Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Euroma KB-10
- Page 1 KB-10 Keyboard User Manual...
- Page 2 Precautions Do not squeeze the LCD panel or leave keyboard under the sun for long hours. Joystick must be properly packaged before shipment for repair. Keyboard must be operate base on recommended temperature and humidity range. Strictly follow the manual's wiring connections. Device Packing List Quantity Item...
-
Page 3: Table Of Contents
Contents 1. Introduction .........................................…..1 1.1 Control..........................................1 1.2. Main and sub-control functions..................................1 1.3. Features ........................................1 2. Installation Instructions ......................................1 2.1. Interface Instructions ......................................1 2.2. Control Key Description ....................................3 2.3. Joystick Description ......................................5 2.4. LCD display........................................6 3. Keyboard settings and queries ....................................6 3.1. -
Page 4: Introduction
1. Introduction KB-10 Keyboard is used to control NVR and front-end devices. 1.1 Control Network Video Recorders are able to completely replace all the functions of remote control operations. All operations are displayed on the LCD screen instructions. A keyboard can simultaneously control multiple NVRs. - Page 5 Physical Interface Connection NVR Keyboard Input Ta,TbConnect NVR Serial Portto AB Port (NVR-CON) NVR Sub Keyboard Input Ra,RbConnect sub keyboard Ta，Tb (NVR-AUX) When connected to NVR or TV wall, indicator light will blink TXD Control Indicator When cascading of keyboard, indicator light will blink RXD Control Indicator When keyboard is in use, red indicator light will be on Power Indicator (PW)
-
Page 6: Control Key Description
2.2 Control Key Description NVR Control QUERY MODE NVR No.: FOCUS+ FOCUS- PRESET CLEAR VIDEO ZOOM+ ZOOM- AUDIO MENU PRESET FULL LOAD PLAY SHOT BRIGHT+ BRIGHT- SCRN PRESET # Help PATROL WIPER LIGHT VIEW LAYOUT *IME BACK Keyboard Button Description Description Functions Back to previous Menu... - Page 7 POW OFF Off / Reboot NVR Switch NVR output：PAL, NTSC, VGA VIDEO OUT Configure NVR audio output AUDIO MENU Enter PTZ mode under NVR mode. PLAY Enter NVR main function menu In NVR control mode, enter NVR single video playback menu; in NVR control mode, enter NVR recording control menu Use NVR to enter Snapshot status SHOT FULL SCRN...
-
Page 8: Joystick Description
2.3 Joystick Description Description Joystick Operation PTZ Control Mode NVR Control Mode Tilt up Control video files quick Down Tilt down Control video slow motion Left Pan left Control video rewind Right Pan right Control video forward Turn Zoom in Clockwise Turn Zoom out... -
Page 9: Lcd Display
2.4 LCD Display All operation buttons will be display on the LCD screen. LCD screen will display if it does not receive any input, the power-saving mode will automatically turn on after 30 seconds(brightness is reduced to a minimum). 3. Keyboard settings and queries Settings and queries can be configured using joystick and buttons on keyboard as follows: 3.1 Keyboard Setting Press... -
Page 10: Typical Wiring Diagram
4. Typical Wiring Diagram Slave Keyboard RS232 RXD TXD GND Master Keyboard RS232 RXD TXD GND Grounding First NVR Second NVR... -
Page 11: Using Keyboard
5. Using Keyboard A keyboard can control multiple NVRs, operate surveillance operation for all functions. The keyboard has two modes of operation: NVR Control: The keyboard can operate NVR. TV Wall Control: Set the correspondence buttons between the video source and video wall. Keyboard mode switching: keyboard will go into default NVR control mode when power on. -
Page 12: Tv Wall Control
3) Rotate the joystick to scroll the menu, press button, playback will pop up on the menu. PLAY Playback: Rotate the joystick and select video then press to start video playback, as shown in the picture. Record Queries: Rotate the joystick to select playback video source press to start video playback. -
Page 13: Camera Control
2) Press button and enter monitor device number, press to confirm. 3) Press button and enter camera number, press to confirm. 4) Users can control the camera operation by using the joystick or right keyboard region. Refer to 5.3. 5.3 Camera Control On NVR control mode, press to operate on camera PTZ. -
Page 14: Technical Parameters
6. Technical Parameters Description Index Multiple NVR Control NVR Control Joystick Joystick RS-422 half duplex Com Port Baud Rate: 9600 LCD Display LCD: 128X64 Com Wiring Max 1200m Operation -10~+50℃ Environment DC-12V ±10% 50Hz Power Power Max 10W Consumption 360(L)X196(W)X110(H) Dimension 2.9kg Weight... - Page 15 20160120...
Need help?
Do you have a question about the KB-10 and is the answer not in the manual?
Questions and answers