Advertisement
Quick Links
Advertisement
Summary of Contents for IKI T600
- Page 1 IKI T600 CHIMNEY Installation instructions 09/2017 ...
- Page 2 1 ...
- Page 3 IKI T600 CHIMNEY INSTALLATION INSTRUCTIONS BEFORE INSTALLATION ‐ Check that all the parts you need are included in the delivery, using the list of parts as reference (pp. 3‐5). ‐ Before piling the stones on the stove and installing the chimney, make sure the stove is horizontally levelled and aligned with the hole in the ceiling. ‐ The safety distance from the outer surface of the flue pipe to inflammable surfaces in a well‐ventilated space is 50 mm in each direction. Do not attach any materials to the surface of the flue unless it comes with a class A1 fire rating. The safety distance from the top of the damper to the ceiling is 40 cm. ‐ The ceiling or wall may have maximum 2 metre overflow after the last support. ‐ The parts for the flue and chimney must be used as they come, and may not be altered or cut. The joints of the pipe sections are secured with tightening straps. INSTALLATION INSIDE THE SAUNA ROOM (PICTURES ON PAGES 7‐8) 1. Install the damper (part 1) on top of the stove’s mesh frame, fasten securely. Position the damper panel to the correct direction in the sauna room (Picture 1). 2. Pass the 1‐metre flue pipe (part 2) through the collar (part 3) (Picture 2). 3. Place the 1‐metre flue pipe (part 2) directly on top of the damper (part 1) (Picture 3). The ceiling collar can simply rest on top of the damper at this stage of installation. 4. Place the tightening strap (part 9) to the joint of the damper (part 1) and the 1‐metre flue pipe (part 2) and tighten securely (Picture 4). Attn! The joint between the damper section and the flue pipe may not need a tightening collar if they fit securely as they are. 5. Use the tape provided to secure the fume blocking plate (part 4) to the fume block in the ceiling tightly (Picture 5). There needs to be a 2‐mm gap between the fume blocking plate and the pipe, which is then taped shut. 6. Attach the collar to the ceiling with the screws (4 pieces) provided in the installation gear box (Picture 6). Detach the protective plastic from the collar. INSTALLATION IN SUBBASE (PICTURES ON PAGES 7‐8) ...
- Page 4 IKI T600 CHIMNEY PIPE LIST OF PARTS: part 1: damper part 2: flue pipe 1000 mm part 3: ceiling collar part 4: fume blocking plate 3 ...
- Page 5 IKI T600 CHIMNEY PIPE LIST OF PARTS: part 5: ceramic fibre insulation part 6: support strap part 7: underlay sheet part 8: chimney cap 4 ...
- Page 6 IKI T600 CHIMNEY PIPE LIST OF PARTS: part 9: tightening strap part 10: cylinder Also included in the delivery: 2 punched tapes of 1000 mm 1 installation gear box with instructions, screws and tape 5 ...
- Page 7 6 ...
- Page 8 Pictures of the installation: Pic 1 Pic 2 Pic 3 Pic 4 Pic 5 Pic 6 Pic 7 Pic 8 7 ...
- Page 9 Pictures of installation: Pic 9 Pic 10 Pic 11 Pic 12 8 ...
- Page 10 Chimney height on roof top Instructions for use Chimney details Damper IKI T600 CHIMNEY PIPE The damper panel needs to be open whenever there is fire CE 1450‐ CPR‐ 0007 burning in the hearth, to not prevent air cooling! EN 1856‐1 T600‐N1‐D‐Vm‐L99080‐G(50) Temperature class T600 Snow barrier Safety distance to inflammable structures 50 mm. There needs to be a snow barrier on the upper side of the chimney to prevent damage to chimney. Three‐sheathed air‐ventilated steel flue and chimney system. Sweeping The chimney may only be swept with a stainless steel or fibre brush. Product plate Warranty The mechanic will fill in the required information regarding The manufacturer, Hormex Oy, Harkkoraudantie 6, the product to the plate included in the delivery. It should 00700 Helsinki, issues a 10‐year warranty for ...
- Page 11 10 ...
- Page 12 Copyright © IKI‐Kiuas Ltd. 11 ...
Need help?
Do you have a question about the T600 and is the answer not in the manual?
Questions and answers