Subscribe to Our Youtube Channel
Summary of Contents for Gared Sports PSS 2300
- Page 1 4 PT STATIONARY WALL MOUNT Models: 2300 Operation and Maintenance Instructions Please read all instructions before attempting operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE Issued UBLICATION 501756246 10-31-2018...
- Page 2 4 PT STATIONARY WALL MOUNT Table of Contents Section Page No. Introduction Parts List Installation Instructions 3-16 Unit Operation Maintenance Introduction Thank you for your purchase of a Model 2300 4 point Stationary Wall Mount Backstop. To ensure that our equipment will provide years of use to you, we are including this operation, and maintenance guide.
- Page 3 4 PT STATIONARY WALL MOUNT Optional Accessories purchased separately: 1131 Manual Height Adjuster 1171 Electric Height Adjuster Locate, identify and count all parts before starting the installation to ensure that all are correct and correspond to the packing list/production drawings. If any parts are missing or damaged, DO NOT SUBSTITUTE.
- Page 4 4 PT STATIONARY WALL MOUNT INSTALLATION PREPARATION Before installing a wall mounted backstop unit, it is imperative the structural integrity of the wall has been evaluated and approved by an architect or structural engineer for the loads that will be imparted to the wall by the backstop.
- Page 5 4 PT STATIONARY WALL MOUNT UNIT LOADING INFORMATION...
- Page 6 4 PT STATIONARY WALL MOUNT TOOLS REQUIRED Plumb Bob or Laser Level Electric Drill Drill bits – 7/16”, 9/16”, 5/8” Hammer Wrenches – 1/2", 9/16”, 11/16, and 3/4" Ratchet Wrenches with 1/2", 9/16”, 11/16, and 3/4" sockets File 4’ Level 25’...
- Page 7 4 PT STATIONARY WALL MOUNT INSTALLATION Installation instructions below are general in nature. Your exact installation needs to follow the parts and any specific instruction included in your specific project’s production drawings. 1. Before installing the wood pads on the wall, you must first preassemble the hinge brackets and chain brackets onto the wood bucks.
- Page 8 4 PT STATIONARY WALL MOUNT WOOD PAD LOCATIONS Always refer to specific dimensions outlined in the production drawings shipped for the specific project. Dimensions of the specific project may vary from the dimensions outlined below. The upper wood pad with the chain anchors should be mounted in the same plane as the two frame mounting wood pads.
- Page 9 4 PT STATIONARY WALL MOUNT WOOD PAD WALL ATTACHMENT When attaching the wood pads to the wall, it is important to place the anchors in a location that will not reduce the strength of the wood. Anchors should be ½” diameter and the holes in the wood pads should be no larger than 9/16”...
- Page 10 4 PT STATIONARY WALL MOUNT Install the outer pipe weldments to the wall brackets on the lower two wood pads. Slide the outer pipe over the bracket tube and insert the flange bushings (Item 6) into both sides of the pipe.
- Page 11 4 PT STATIONARY WALL MOUNT Install the chains on each side of the unit. Attach the chain to the upper chain supports with the 5/16” quick links. Make sure the links are fully closed and tightened. Attach the turnbuckle to the chain attach plate with a 5/16”...
- Page 12 4 PT STATIONARY WALL MOUNT INSTALLING THE BACKBOARD WITHOUT A HEIGHT ADJUSTER Support the outer portion of the extension arms with the scissor lift or scaffolding. Attach the back board to the board hinge mounts using the appropriate board mounting hardware. Note, a glass board and carriage bolt hardware is shown.
- Page 13 4 PT STATIONARY WALL MOUNT The final step of the assembly is to level the frame extension arm by adjusting the chain tension with the turnbuckles. It is important to not over adjust the chains as this causes undue stress on the chain anchor points.
- Page 14 4 PT STATIONARY WALL MOUNT INSTALLING THE BACKBOARD WITH A HEIGHT ADJUSTER Square each side of the frame to the wall and support the outer portion of the extension arms with the scissor lift or scaffolding.’ Attach the height adjuster frame using the 3/8 x 1 ½”...
- Page 15 4 PT STATIONARY WALL MOUNT Install the locking bolts on the extension arms the prevent movement of the arms. Drill a 7/16” hole through the inner extension tube using the hole in the outer tube as a guide. Install the 3/8” bolt (Item 28), locknut (Item 30) and tighten securely.
- Page 16 4 PT STATIONARY WALL MOUNT ATTENTION: INSTALLER To confirm that you have received all the parts, and to better serve you if you contact us, please fill out the following information and fax or mail to the address below. Please refer to the facility name and/or the installation company below when you contact the factory, and include it on any correspondence.
- Page 17 4 PT STATIONARY WALL MOUNT Model 2300 Installation Checklist Date: ________________ Unit Number Building structure has been approved for unit loads. Attachment anchor system has been approved for the unit loads and installed per the structural engineer’s specifications. Washers have been installed under wood pad’s carriage bolts.
- Page 18 4 PT STATIONARY WALL MOUNT OPERATING INSTRUCTIONS Always use the equipment in the manner intended. The manufacturer does not assume any liability for improperly used or improperly maintained equipment. Always check for any loose connections, chains, or components before using the equipment. Contact the appropriate maintenance personnel if any components are noticed to be loose or out of place.
- Page 19 4 PT STATIONARY WALL MOUNT MAINTENANCE INFORMATION – PLEASE RETAIN FOR FUTURE REFERENCE!!! MODEL #2300 4 PT STATIONARY WALL MOUNT MAINTENANCE OVERVIEW !!!ALWAYS DISCONNECT POWER SOURCE BEFORE PERFORMING ANY MAINTENANCE CHECK OR OPERATION ON THIS EQUIPMENT!!! STRUCTURE: We recommend a yearly inspection (or more frequently depending on usage) of the nuts and bolts, checking for...
- Page 20 4 PT STATIONARY WALL MOUNT ATTENTION: MAINTENANCE DEPARTMENT To confirm that you have received maintenance and warranty information, and to better serve you if you contact us, please fill out the following information and fax or mail to the address below. Please refer to the facility name and/or the installation company below when you contact your dealer, and include it on any correspondence.
- Page 21 4 PT STATIONARY WALL MOUNT Maintenance Check Sheet Refer to Maintenance Overview (page 18) for recommended inspection frequency. Date:________________ Unit:___________________ Wood Pads / Anchors -Wood pads, splitting, chipping, etc. Repair Replace -Anchors/Bolts Repair Replace Unit Supports / Brackets / Hinges -Tubes;...
- Page 22 Gared Holdings, LLC Performance Sports Systems Gared Sports 9200 E. 146 Street 9200 E. 146 Street Noblesville, IN 46060 Noblesville, IN 46060 800-848-8034 800-325-2682 www.perfsports.com www.garedsports.com...
Need help?
Do you have a question about the PSS 2300 and is the answer not in the manual?
Questions and answers