Advertisement
2. APPLICATION & SPECIFICATION
the sM47.V3 is designed to extract dust, saw dust and other fine debris from wood machining. It should not be used to extract metallic
debris, glass or water.
Specification:
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700cfm
Impeller diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mm
collector hose diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125mm
Intake hose diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 100mm
Intake hose maximum length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5m
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V, 50Hz, 1490W
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46kg
noise level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<87dBA
3. CONTENTS & ASSEMBLY
unpack the extractor components and check that all are present and undamaged. In case of shortage or damage please contact the supplier.
Description:
• Collector Body with Motor
• Seal
• Base plate
• Hose
• Hose Clamp x 2
Note: Numbers in brackets are the item numbers on the parts diagram and in the parts list.
3.1
Attach the four castors (1) to the underside of the base (3) using screws (23), washers (16) and nuts (19). support base (3) on
battens, or similar, raising castors clear of floor to give stability for the following assembly tasks.
3.2
With screws (6) and washers (4) attach motor base (5) to base (3).
3.3
Attach motor (8) to motor base (5), so that collector body is positioned as shown in parts diagram, with screws (6) and washers (4).
3.4
Attach fan housing (38) feet to base plate (3) with screws (6) and washers (4).
3.5
Install outlet (30) to fan housing (38) using packing (29), screws (15), washers (16) and nuts (19).
3.6
Attach collector supports (37) to base with screws (12) and washers (4) and to collector (33) with screws (6) and washers (4). note
that upper bag support (13) is fitted to the collector (33) with the same screws as the middle support (37).
3.7
fit upper (filter) bag (35) over upper bag flange on collector (33) and secure by tightening built-in strap. Hook loop on end of bag (55)
over support arm (13). fit second (collector) bag (36) to lower bag flange on collector.
Note: Bag clamps (34) are provided and may be used for additional bag security.
3.8
Install hose (32) between outlet (30) and collector (33) and retain with hose clamps (31).
3.9
Push-fit inlet (24) to inlet cover (25).
4. OPERATING INSTRUCTIONS
WARNING! before operating the extractor ensure that you read, understand and apply the safety instructions in Section 1.
4.1
confirm that supply voltage matches the voltage shown on the motor data plate and that the motor switch (9) is 'off'.
4.2
connect extractor hose (39) to the inlet (24) and attach other end to extractor point on equipment. If only one extractor hose is to
be used ensure that the unused inlet is closed with the cap provided.
WARNING! DO NOT operate extractor without the hose(s) attached.
4.3
Plug into mains supply and press motor switch 'on'.
4.4
Ensure that the lower bag is emptied of dust and chips on a regular basis and is not allowed to become full.
Note: fitting a reducer to the extraction hose will reduce the volume of dust extracted.
WARNING! this unit is not suitable to be used to extract dust via a piped system.
5.
DECLARATION OF CONFORMITY
Declaration of Conformity
directives.
DUST & CHIP EXTRACTOR
Model SM47.V3
2006/95/Ec Low Voltage Directive
2004/108/Ec EMc Directive
2006/42/Ec Machinery Directive
93/68/EEc cE Marking Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: no liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: for a copy of our catalogue and latest promotions call us on 01284 757525 and leave your full name, address and postcode.
• Filter/Collector Bag x 2
• Support, Collector x 2
• Screws, Nuts, Washers (1 bag)
• Inlet
• Bag Clamp x 2
We, the sole importer into the uK, declare that the product listed here is in conformity with the following standards and
the construction file for this product is held by the Manufacturer and may be inspected, by a
national authority, upon request to Jack sealey Ltd.
For Jack Sealey Ltd. Sole importer into the UK of Sealey Quality Machinery.
Sole UK Distributor
Sealey Group,
Bury st. Edmunds, suffolk.
• Collector
• Support Rod, Filter Bag
• Castors x 4
• Outlet
• Inlet Hose (2.5m)
signed by Mark sweetman
01284 757500
01284 703534
16th March 2009
www.sealey.co.uk
Web
sales@sealey.co.uk
email
sM47.V3
Issue no: 4 - 16/03/09
Advertisement
