Advertisement
Quick Links
Multiple Flexiele Monitors Stand
Installation Instruction
· Image may different from the actual product.
· Make sure the package is perfect before sign it, if any defect please ask
carrier confirm it.
· Verify all the parts are included, not all the hardware included will be used.
· Install according to manual, or improper installation and assemble may cause
display to fall suddenly so producer will not response for any loss or injury.
· The product contains small items so keep away of children.
· Choose approximate place for mounting, and be aware of display size,extension
height adjustment,maxium weight capacity and pitch or roll requirement.
C2L
WARNING
P 1/8 A-01
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Pixio C2L
- Page 1 Multiple Flexiele Monitors Stand Installation Instruction WARNING · Image may different from the actual product. · Make sure the package is perfect before sign it, if any defect please ask carrier confirm it. · Verify all the parts are included, not all the hardware included will be used. ·...
-
Page 2: Parts List
Parts list: Desk clamp 1X Arm assemble 1 Pole assemble 3 (M4x12)-8 pcs (M4x16)-8 pcs (8.0mm*80mm)-1 pcs (5.0mm*150mm)-1 pcs (Ø8.0*Ø5.5*5mm)-8 pcs (2.0mm*50mm)-1 pcs (4.0mm*60mm)-1 pcs step 1 Figure1-1 Figure1-2 Clamp-1 Clamp-2 Install grommet clamp and Install desk clamp and screw screw tightly with 8mm allen tightly with 8mm allen key key (Figure1-3) - Page 3 step 2 Install the desk part (Figure 2-2） Figure2-1 Screw the pole then connect with the desk part (Figure 2-1） Figure2-2 step 3 Take arm assemble（1）to attach the pole assemble（3）， then adjust the height properly,and tighten adjust lock collar as Figure 3-1 Lock Collar Figure3-2 Use 8mm(C) allen key to tighten the...
- Page 4 step 4 Place the display face down on protective surface， and choose proper screw.When turn the two screws in the upper back face,make sure the distance is 2-4mm between the head of screw and display as Figure 4-1. 2~4mm Figure4-2 Figure4-1 step 5 Choose C or D proper screw for...
- Page 5 step 6 Attach the display with two screws in the center mount bracket，then use Philips screwdriver to tighten the two screws. Stop suddenly when you encounter any resistance. as Figure6-1 Figure6-2 Then take proper screws to tighten the other two screws (Figure6-2) Figure6-1 step 7 Figure7-1...
- Page 6 step 8 Figure8-4 The product can tilt forward and backforward+12/-12 degree to get good view.And also can adjust horizontal level.Use 4mm allen key(G) to tighten or loose the control hex screw as Figure 8-1～8-4. Figure8-2 Figure8-3 Figure8-1 step 9 Move the monitor and get zero distance Warning: When loose the between monitors，then loose or tighten screw screws Only one loop,...
- Page 7 step 10 Figure10-1 Loose the screws by hand to slide left and right. step 11 Figure11-1 Swing Swing adjustment adjustment Displays in both sides can come forward 0～18 degrees to suit different view angle. Then use 4mm allen key(G) to tighten or loose to get required angle as Figure11-1. P 7/8 A-01...
- Page 8 step 11 Attach the cable to the arm and pole with plastic clip and insure enough slack is left in the cables to allow for movement. Use the cable clip to secure the cables to the pole and get clean look as Figure 11-2 Figure11-2 P 8/8 A-01...
Need help?
Do you have a question about the C2L and is the answer not in the manual?
Questions and answers