Advertisement
Installation Instructions
Please Note: A UHF aerial can be
connected directly to the UHF input
on the amplifier or connected via
a Satellite Receiver.
LDL208LP
Remote Powered
Digi Eye
Lte
MRX955
800
POWER
READY
1
2
RF In
TV
PSM114E
TV
Amplifier
No of Inputs
No of Outputs
Return Path Frequency Range
Return Path Gain
Frequency Range
UHF/FM/DAB Gain per port
Max Out put level (IMA3-60dB). EN50083-5
Noise Figure
All Ports IR Enabled
Isolation between outlets
Dimensions
Power Supply
DC Output
Output Voltage Tolerance
Power Requirement
Signal Insertion Loss
Dimensions
2
Or
3
4
5
6
7
8
SAT
RF2 OUT
Remote Rooms
PSW111
PSW122
Suitable for combined
Suitable for TV outlet
TV and Radio outlet
Digi Eye
MRX955
TV
FM/DAB
RF In
VCR/DVR
TUNER
LDL206LP
LDL208LP
2
6
8
5-15MHz
5-15MHz
-4dB
UHF: 470-790MHz FM/DAB: 47-300MHz
8dB
98dBµv
96dBµv
3.5dB
9V 15mA short circuit protected
20dB
265 x 95 x 35mm
PSUF
12VDC at 200mA max.
± 5%
220-240V~50Hz at <3W
0.5dB
88 x 67 x 45mm
Installation
Important note: attention is drawn to the General Safety Precautions Panel on page 4 which
contains advice on safe installation and operation of these products.
Location
Choose a location for the amplifier from which it is convenient to run cables from the
antennas and to the system outlets. Typical examples of suitable locations are a loft space or a
cupboard. In weak signal areas it is best to keep the antenna cables as short as possible.
Select a cool, dry location to install the amplifier. This means a location where the ambient
temperature will remain between -10°C and +40°C, and which is free from risk of dripping or
splashing water.
The fixing location should allow adequate access to the equipment for wiring and maintenance.
Clearance of at least 25mm should be allowed around the top and left hand side of the amplifier
and also around the three sides of the power supply that don't have connections to allow
adequate ventilation. More clearance will be needed on the sides with connections to allow
access for cables.
TV
Fixing
The amplifier should be fixed to a wall or other suitable hard surface, using suitable screws and
masonry plugs (not supplied). The amplifier should not be left supported by its own wiring, nor
should it be left resting on a carpet or other insulating and/or inflammable surfaces.
Electricity Supply
TV
Fixed wiring and connection of the electrical supply to these products should be carried out in
accordance with BS7671 (IEE Wiring Regulations) .
Each amplifier is supplied with a separate PSUF fitted with a 13A mains plug. If this is not
suitable, see General Safety Precautions Panel on page 4. As an alternative to the use of plug
and socket connection, the power supply may be connected to the mains using a switched
fused connection unit BS 1363-4. A 3 Amp fuse to BS1362 should be fitted in the fused
connection unit. If the power unit is connected to the supply other than by means of its fitted
fused plug or a fused connection unit, It must be protected by a non-time delayed fuse or a
type B MCB at the distribution board of rating not exceeding 6A. An isolating switch should be
provided near to the unit to allow it to be disconnected from the supply when necessary.
Signal Connections
Input and output signal connections are made using F type (IEC 60169-24) connectors.
Good quality plugs should be used, preferably of the crimp on type. If twist on connectors are
used make sure they are the right size to fit the cable you are using. For outside connections
use waterproof connectors. Attention is drawn to the need to maintain DC continuity through-
out the system for correct operation of infra-red remote control functions
Resetting RF Channel on a Digibox
1. Switch on your Sky™/Sky+™/ Sky+ HD™ receiver and view on your main television.
2. Press the SERVICES button on your Sky™ remote.
3. Select SYSTEM SETUP option (for SKY+ HD there is no SYSTEM SETUP option press 0 instead).
4. Press the following buttons in sequence: 0, 1, SELECT (for SKY+ HD this is a hidden option
and does not appear on screen). You should now see the installers' menu.
5. Select the RF CHaNNEL NUMbER option and key in a new channnel number from 21-58.
Make a note of the channel number you choose as you may need it when tuning your
other TVs.
Installation Instructions
3
Advertisement
