Bahco BBCE12-10 Owner's Manual page 8

Automatic
Hide thumbs Also See for BBCE12-10:
Table of Contents

Advertisement

LED INDICATOR
GREEN LED solid (CHARGING): T e
GREEN LED pulsing (CHARGED/MAINTAINING): T e attery is fully
arger is in Maintain Mode.
GREEN LED ashing: T e
NOTE: See Operating Instructions for a omplete des ription of t e
12. OPERATING INSTRUCTIONS
T is attery
WARNING
assem ly instru tions efore it is used.
T e
arger does not ave an
y plugging t e BBCE12-10 into an AC ele tri al wall outlet only after t e attery
onne tions ave een made.
Do not start t e ve i le wit t e
IMPORTANT
may damage t e
BATTERY INFORMATION
T
is
arger an
arge 6- elled lead-a id atteries wit rated apa ities of 10-230 A .
NOTE: T is
arger is e uipped wit an auto-start feature. Current will not e supplied
to t e attery lamps until a attery is properly onne ted. T e lamps will not spark if
tou
ed toget er.
See instructions for charging a battery inside a vehicle (Section 6) or outside of the
vehicle (Section 7).
USING THE QUICK-CONNECT CABLE CONNECTORS
Conne t any of t e output a le assem lies to t e
E ER onne t t e lip and ring terminal onne tors toget er for use in ot er
IMPORTANT
appli ations, su
extend t e output a le lengt , as reverse polarity and or over arge onditions will o ur.
BATTERY CLAMP QUICK-CONNECT
1. Conne t t e end of t e
2. Follow t e steps in se tions 6 and 7 to onne t t e lamps to t e attery.
3. After a good ele tri al onne tion is made to t e attery, plug t e power ord into an AC
ele tri al wall outlet. Make sure to pla e t e
4. W en t e
arger starts, t e GREEN LED will e solid, and t e display will s ow
ANALYZING BATTERY w ile t e
onne ted and t e ondition of t e attery.
5. W en t e attery is fully
6. W en
arging is omplete, dis onne t t e AC ord from t e supply mains, remove t e
lamp from t e ve i le s
RING TERMINAL QUICK-CONNECT
T e ring onne tors permanently atta
arge your attery. T is appli ation is appropriate for motor y les, lawn tra tors, AT s
and snowmo iles.
1. To permanently atta
attery terminals.
2. Conne t t e red positive onne tor ring to t e positive P S, P,
3. Conne t t e negative onne tor ring to t e negative
4. Repla e and tig ten t e nuts to se ure t em.
5. Conne t t e ring onne tor a le assem ly to t e
wires and plug away from ot and moving parts.
6. Plug t e
arger power ord into an AC ele tri al wall outlet. Make sure to pla e t e
arger on a dry, non- amma le surfa e.
arger is onne ted and is
arge as a orted. See Aborted Charge se tion .
arger must e properly assem led in a ordan e wit t e
FF swit
. T e
arger onne ted to t e AC outlet, or it
arger and your ve i le.
as external attery or ot er power sour e
arger output a le to t e end of t e attery lamp ui k- onne t.
arger on a dry, non- amma le surfa e.
arger determines t at t e attery is properly
arged, t e GREEN LED will pulse.
assis, and t en remove t e lamp from t e attery terminal.
to t e attery, providing easy a ess to ui kly
to a attery, loosen and remove ea
8
arging a attery.
arged and t e
arger modes.
n and
ff ommands are ontrolled
arger in se onds.
arging, or to
nut from t e olts at t e
attery terminal.
E , , -
attery terminal.
arger. Take are to keep ot

Advertisement

Table of Contents
loading

Table of Contents