2N SmartCOM Quick Manual

Read the User Manual carefully to get familiar with all system functions.

Security Precautions

 Do not switch on 2N
medical apparatuses to avoid interference. The
minimum distance of the antenna and pacemakers
should be 0.5m.
®
 Do not switch 2N
 Do not switch 2N
chemical facilities or sites where explosives are
used.
 Any mobile telephone use prohibition based on RF
energy radiation applies to 2N
®
 2N
SmartCOM may disturb the function of TV sets,
radio sets and PCs.
®
 Warning! 2N
SmartCOM contains components that
can be swallowed by small children (SIM card,
antenna, etc.).
®
 When 2N
SmartCOM comes to the end of its
operational life, dispose of it in accordance with
applicable regulations.
®
 2N
SmartCOM is equipped with an external
antenna connector. The antenna has to be located
indoors for safety reasons.

Basic Functions

®
 2N
SmartCOM is designed for bidirectional data
transmission between serial ports and their
opponents based on GPRS data transmission
via the GSM network.

Installation Conditions

 Install the GSM antenna with respect to the
signal quality in the location.
®
 Keep 2N
SmartCOM off sensitive devices and
human bodies to avoid EM interference.

External Antenna Connection

Screw the enclosed antenna into the SMA
antenna connector.
connector gently with your hand, never use a tool!

SIM Card Installation

Insert the SIM card in the hole in the upper part of
®
2N SmartCOM making sure that the bevelled
edge of the SIM card faces the green connector
(see the figure on the front side of the product).
Remember to set the relevant provider's services
(PIN request, e.g.) on your mobile phone before
inserting the SIM card in 2N

LED Statuses

No light
Three fast flashes
Slow blinking
Very fast blinking
Continuous light
®
2N SmartCOM Quick Guide
®
SmartCOM in the vicinity of
SmartCOM aboard a plane.
®
SmartCOM near petrol stations,
®
SmartCOM too.
Tighten the antenna
®
SmartCOM. Make
Device not supplied
Start or restart
Connecting to network, starting GPRS, connecting to 2N
Error: wrong PIN or SIM not inserted
Connected, IP address assigned, connected to server in TCP Client mode
(flashes when transmitting data)
A SmartCOM
following:
®
2N SmartCOM
Antenna
Supply adapter
8-pin terminal board
Product CD
 Do not place the unit near heat sources
(such as
heaters, etc.)
necessary.
®
 2N
SmartCOM only works reliably
under the conditions specified in the
operating
unauthorised
changes in use and operation may
result in malfunction or destruction of
the product.
sure that the provider's SIM card is intended for the
GSM network supported by your 2N
version and that the GPRS data transmission is
activated with an IP address enabling incoming
connection (unless you use the 2N
server).

Power Supply

®
2N SmartCOM is DC supplied from a 12V/0.5A
power adapter included in the delivery. The use
of any other
®
2N SmartCOM. Do not connect the power
supply until you have connected the antenna to
avoid the GSM module damage!

Initialisation

Once you connect the power supply, the GSM
module, inputs, outputs, serial interfaces and
configuration module
®
2N SmartCOM can be regarded as functional if
the LED indicator signalling GSM connection and
IP address assignment (or connection to the
server in the TCP Client mode) keeps shining
constantly. Refer to the LED Statuses table
below for initialisation and operation details.
delivery contains
space heaters, hot air
unless absolutely
instructions.
interventions and/or
®
SmartCOM
®
SmartCOM
adapter may damage
will get initialised.
®
SmartCOM Server
the
1 pc
1 pc
1 pc
1 pc
1 pc
Any