Summary of Contents for NARGESA TS10
- Page 1 WELD POSITIONER TS10 INSTRUCTIONS BOOK PRADA NARGESA, S.L Ctra. de Garrigàs a Sant Miquel s/n · 17476 Palau de Santa Eulàlia (Girona) SPAIN Tel. +34 972568085 · nargesa@nargesa.com · www.nargesa.com...
- Page 2 Thank you for choosing our machines www.nargesa.com...
-
Page 3: Table Of Contents
3.3. Connection to the power supply .................. 4. INSTRUCTIONS FOR USE ..................... 4.1. Panel description ......................4.2. Introduction ......................... 4.3. Feeding of the Positioner TS10 ................... 4.4. Activation of the Positioner TS10 ................4.5. Memories of continous welding ................... 4.6. Memories of discontinous welding ................ -
Page 4: Characteristics Of The Machine
Picture 1. External dimensions of the Weld positioner 1.3. Description of the machine TS10 has been designed to weld different circular parts in different positions and kinds of welding. TS10, is according to the European regulations and normative for the manufacturing of machinery If an accident occurs by negligence of the operative, for not following the safety rules exposed on this manual, PRADA NARGESA S.L will not accept any responsibility. -
Page 5: Identification Of The Components
Engine hose welding pincers Turning plate Oparation pedal Encoder hose Potenciometer to regulate turning speed Motor reducer LED’S light pilots Emergency stop Information display Operations keyboard Main switch Picture 2. Nomenclature and position of components INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 6: General Characteristics
Welding type Continous or discontinous Horizontal maximum capacity 75 Kg Vertical maximum capacity 55 Kg Round plate diemeter 395 mm Plate thickness 10 mm Bench height 790 mm Dimensions 520x640x790 mm Weight 61 Kg INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 7: Transport And Storage
* Temperature from -25 to 55ºC or 75ºC for length of time no longer than 24h * It is advisable not to pile up machines or heavy objects on top of them. * Do not dismantle for storage. INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 8: Instalment And Starting Up
IMPORTANT: This machine must be connected to a socket with ground connection. TS10 is equipped with a 230v and 0.12 kW single phased engine to be connected to a 230v power supply. It must be connected to an only power supply in the indicated source. -
Page 9: Instructions For Use
4. INSTRUCTIONS FOR USE 4.1. Panel description Potenciometer to Emergency button regulate turning speed Information display LED’S light pilots Operations keyboard Main switch Picture 6. Control panel of the Welding Positioner. INSTRUCTIONS BOOK OF WELD POSITIONER TS10... - Page 10 IT ALLOWS THE ACCESS TO THE TIME PARAMETER OF STARTING OF THE WELDING PROCESS (WELDING STOKING TIME) IT ALLOWS THE ACCESS TO OVERLAPPING PARAMETER (IT SURPASSES WELDING FROM 360º) IT ALLOWS ACCESS TO PERFORMANCE OF THE TS-10 WITH A WELDING ROBOT INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
-
Page 11: Introduction
If in this moment we press the pedal, the positioner starts turning in the indicated direction while it shows on screen the the speed and current angle like in the label below: SPEED 10º/S POSITION 0º Picture 10. Information of TS10 in positioner mode INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 12: Memories Of Continous Welding
Picture 14. Screen for Weldinf Starting Time · The Overlapping key gives direct access to the parameter of this memory whenever the memory is 360º. MSC00-> -> POSIT OVERLAP 20º Picture 15. Overlapping angle screen INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 13: Memories Of Discontinous Welding
10 existing discontinuous memories will show up on screen. The selection has been made by using the moving keys (up and down arrows) and pressing the OK key. DISCONTINOUS: 00 WELDING Picture 19. Information of the current discontinuous welding memorys INSTRUCTIONS BOOK OF WELD POSITIONER TS10... - Page 14 MSD00 -> -> POSIT END ANGLE 90º Picture 24. Screen for the Right turning dire MSD00 <- <- POSIT END ANGLE 90º Picture 25. Screen for the Left turning direction INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
-
Page 15: Robot Mode
· The positioner will go back again in absolute “0” or Starting welding point. Note: Remember all signs coming from the Robot must be Potential free. Parameters start time and overlap also works in robot mode. INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 16: Memories Of Continous Welding At Robot Mode
Picture 32. Screen for Welding starting point · The Overlapping key gives direct access to this parameter on the memory whenever it is 360º. MSC00 -> -> ROBOT SOLAP 20º Picture 33. Screen for the Overlapping Angle INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 17: Memories Of Discontinous Welding At Robot Mode
Picture 37. Information of the current discontinuous memory Now the following parameters will appear. . Indication of the start and end of the welding. (In degrees) MSD00 -> -> ROBOT START ANG 0º Picture 38. Screen of the discontinuous welding memory INSTRUCTIONS BOOK OF WELD POSITIONER TS10... - Page 18 Picture 43. Screen of Left turning direction MSD00 <- <- ROBOT STARTING TIME 3 S Picture 44. Screen of Welding Start Time MSD00 <- <- ROBOT SOLAP 20º Picture 45. Screen of Overlapping angle INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 19 360º CURRENT 0º Picture 46. Screen of Pantalla de Memoria de soldadura discontinua When a welding operation ends, the plate locates in a new starting point of the memory that has been currently selected. INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
-
Page 20: Warnings
- Keep a safety distance between the machine and the operative during the time the machine is performing. -In case an accident due to a negligent use of the operative, for not bearing in mind the safety rules exposed on this book, NARGESA SL will not accept any responsibility. INSTRUCTIONS BOOK OF WELD POSITIONER TS10... -
Page 21: Technical Annex
Technical annex Weld Positioner TS10 List of parts Electrical map Electric box connections Electronic plate... - Page 22 A1. List of parts INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 23 INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 24 A2. Electrical map INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 25 A3. Electric box connections INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 26 A4. Electronic plate INSTRUCTIONS BOOK OF WELD POSITIONER TS10...
- Page 27 3. Complete the form with your details and press Message Sent: confirms your data has been successfully sent to Prada Nargesa SL. Your machine has been registered and has a warranty of three years in total. Your request has been sent correctly. We will contact you right...