Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Planet IDL-4802
Summary of Contents for Planet IDL-4802
- Page 1 48-Port ADSL 2/2+ IP DSLAM IDL-4802 / IDL-4802-48 Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents Package Contents .................... 3 Overview ......................4 Safety Instruction .................... 6 Hardware Installation ..................7 1. Power and Ground Connections ..............7 2. FAN Cable Connection ................9 3. ADSL and POTS Connections ..............9 4. Uplink Interfaces Connections ..............10 5. -
Page 3: Package Contents
Package Contents IDL-4802 ¢ IDL-4802 Unit x 1 ¢ AC Power Cord x 1 ¢ CD x 1 ¢ Quick Installation Guide x 1 ¢ 2-Meter Telco-50 Cable x 4 ¢ Console Cable x 1 ¢ Rack-mounting Ear x 2 ¢... -
Page 4: Overview
Overview Front Panel The front panels are shown below. IDL-4802 IDL-4802-48 Interface Definition Interface Description POWER Power On / Off switch. -48V DC Power plug-in. -48V (*IDL-4802-48) RJ-45 port for connection with the RJ-45 port on the front panel of fan card to provide power to the fan. - Page 5 DSL status Green ADSL Port is Disabled Flash ADSL Port is activated but not linked Rear Panel The rear panels are shown below. IDL-4802 IDL-4802-48 Port Definition Port Description AC Power cord plug-in, 100 - 240VAC is allowed. AC PWR...
-
Page 6: Safety Instruction
Safety Instruction The following is the safety instructions for IP DSLAM before installing. >> The maximum operating temperature of the IP DSLAM is 65ºC. Care must be taken to allow sufficient air circulation or space between units when the IP DSLAM is installed inside a closed rack assembly and racks should safely support the combined weight of all IP DSLAM. -
Page 7: Hardware Installation
1. Power and Ground Connections Power Connections With IDL-4802, connect the AC power cord to the AC supply socket on the rear panel as below figure, and plug the cord into the external power source. The voltage must be 100 to 240V AC. - Page 8 ¢ In Remote Cabinet: The IDL-4802 should be grounded by connecting a #14 or #12 AWG conductor between the grounding screw (on the rear panel of the DSLAM, refer to below figure) and the earth ground or main grounding bar. The resistance between the chassis and the grounding bar should be less than 25 Ohm.
-
Page 9: Fan Cable Connection
ERR3 Status 3. ADSL and POTS Connections The IDL-4802 supports 48 ports ADSL subscribers per box. There are four RJ-21 50-pin female connectors on the front panel of the system. Two for ADSL lines and two for POTS interfaces. To connect the subscriber lines, use cables with the RJ-21 50-pin male connectors. -
Page 10: Uplink Interfaces Connections
Please plug-in the RJ-21 cable with connector tenon as below figures. 4. Uplink Interfaces Connections The system provides two types of trunk interfaces (two ports for each type). There are electrical (RJ-45) and optical (SFP) interfaces. When both electrical and optical ports are connected, system will automatically select the interface according to the priority setting (Fiber first or Copper first). -
Page 11: Management Port Connection
PC COM port. 7. Housekeeping Connection The IDL-4802 equips with a RJ-50 port (HK) on the front panel to provide four housekeeping inputs and one alarm contact output. Generally, housekeeping contacts can connect to environment-sensor-controlled switch to indicate the... - Page 12 The HK circuit contains a photo coupler powered by the IDL-4802 to detect the "open" or "close" status of the loop between HK_IN and HK_COM (users don’t need to feed 3.3v power into the circuit). As to the alarm output, there is a relay between ALMOUT and ALMCOM to control the status of the loop to be "OPEN"...
-
Page 13: Web Configuration
WEB Configuration This section describes how to use Web Configuration Tool to maintain your IP DSLAM. The IDL-4802 contains a HTTP server. You can login and configure it by using your Web Browser. Preparation Before attempting to configure the IDL-4802, please ensure as below: Set your computer’s IP with the same network segment of the IP DSLAM. - Page 14 Step 2: Login the IDL-4802 A login page will appear. Please type your username / password and click "Sign in". (The default username / password is admin / admin) After you login the IDL-4802, you will see the system information as below.
- Page 15 Step 3: Configure the DSL PVC Go to "Bridge Ë Interface Setup Ë ADSL PVC" setting screen, select the ADSL port and click “Create” to apply the PVC settings. (For example, create PVC-1 to Port 1. The default VPI / VCI is 0 / 35) You can see the Port has been created.
- Page 16 Step 4: Enable the ADSL Port Service Go to "System Ë ADSL Port Service" setting screen, select the ADSL port and Admin is "ON". Click "Modify" to make this Port is ON. You can see the Admin status became to ON.
- Page 17 Connect the ADSL2/2+ CPE to Patch Panel and configure it, the VPI / VCI value must be the same with IDL-4802. After finish setting, the CPE will establish the ADSL connection with IDL-4802. You can check the connection status as below figure. The Current Status is ON.
- Page 18 Step 6: Save the running configuration to Flash Remember to save your running configuration to the flash, otherwise the settings will be lost if you power-off IDL-4802. Go to "Maintenance Ë Database" setting screen, select the "(D) Save Running Config to Flash (System Config)". There are two partitions on flash, select your Partition which you want to save and click "Write Running".
-
Page 19: Further Information
Further information For further detail configurations and information can be found in the user’s manual CD. If you have any other questions, please contact the local dealer where you purchasing this product. - Page 20 This page is intentionally left blank...
Need help?
Do you have a question about the IDL-4802 and is the answer not in the manual?
Questions and answers