Advertisement
2. INTRODUCTION & SPECIFICATION
Features tilt and swivel head for optimum air circulation. Remote control operation and fully guarded fan blades to BS5060/IEC 879 for ease of
use and extra safety. Smooth running motor powers both fan blades and head oscillation.Timer function allows user to preset running time
between 30 minutes and 4 hours. Features three modes - Normal, Nature and Sleep. Nature mode for alternating high and low airflows. Sleep
mode for gradual reduction of fan speed. Supplied with wall bracket for quick and easy installation.
Model No: . . . . . . . . . . . . . . . . . .SWF16WR.V2
Fan Diameter:. . . . . . . . . . . . . . . .400mm (16")
Speeds:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Modes: . . . . . . . . . . . . .Normal, Nature, Sleep
Maximum Airflow: . . . . . . . . . . . . . 40mtr³/min
Power:. . . . . . . . . . . . . . . . . . . . . . . . . . . . .50W
Supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . .2.37kg
3. ASSEMBLY
Unpack carton and assemble the fan as follows:
3.1.
Unscrew and remove the large plastic locking cap from the motor spindle of the fan (Note: left hand thread). Then unscrew and
remove the plastic locking ring (Fig.1.1) from the motor housing.
3.2.
Fitting the rear fan guard.
Identify the rear fan guard by the location holes in the centre plate (Fig.1.2) and place the guard over the fan spindle and fit onto the
three location pins (Fig.1.3).
3.3.
Secure the rear guard with the plastic locking ring (Fig.1.1).
3.4.
Fitting the fan blade.
Slide the fan blade onto the motor spindle until it comes to rest against the pin, ensure the pin engages with the cutouts on the
blade. Thread the large plastic locking cap onto the end of the motor spindle by turning it anticlockwise. Hold one of the fan blades
and tighten the cap down onto the fan.
3.5.
Fitting the front fan guard to the rear fan guard.
Hook the clip on the top of the front guard (Fig.2.A) over the rear guard and fit and tighten the screw and nut at the bottom of the guards
(Fig.2.B). Slide the four other clips on the front guard down to secure the guards together.
3.6.
Check that the guard has been assembled correctly and that the fan will turn freely before plugging into the mains.
The fan is now ready to use.
4. OPERATION
WARNING! Ensure you read, understand and apply the safety instructions in Section 1
before using the fan.
4.1.
Mount on a suitable wall location using the included bracket and three fixings. Plug into the
mains power supply.
4.2.
Adjust tilt of fan as required.
4.3.
Using the remote control, press the Speed/On button to switch the fan on.
4.4.
Adjust the fan speed by pressing the speed button. The sequence is Low - Medium - High.
4.5.
Set the timer by pressing the timer button. The timer can be set from 30 mins to 4 hours.
Each press increases the time and is indicated by the appropriate lights.
Note: more than one light may light up - add together the lit up times to reach the time set.
4.6.
To make the fan oscillate, press the swing button. To stop the fan oscillating, press the button
again.
4.7.
MODES: the fan has three mode settings, these are selected by pressing the Mode button to
cycle through them. The three modes are: Normal, Nature and Sleep.
- Normal is a constant speed.
- Nature is a fast / slow alternating speed.
- Sleep is the same as Nature initially, then after 30 mins, the strength will gradually
decrease.
4.8.
When the fan is no longer required, press the Off button and remove plug from mains socket.
Store in a safe, dry, childproof location.
5. CARE OF FAN
IMPORTANT: Turn the fan OFF and disconnect from power supply before cleaning.
5.1.
Use only a soft, damp cloth to clean the fan.
5.2.
DO NOT submerse the fan in water and NEVER allow water to drip into the motor housing.
5.3.
DO NOT use solvents or other chemicals to clean the fan.
5.4.
To clean the fan blades, remove front guard - reverse of assembly sequence 3.5. above.
5.5.
Wipe the blades and guards clean.
5.6.
Reassemble front guard - see assembly sequence 3.5. and 3.6. above.
5.7.
Store the fan in its original box or otherwise cover the fan to protect it from dust.
© Jack Sealey Limited
Original Language Version
Fig.1
Fig.2
SWF16WR.V2 Issue: 2(L) - 24/02/14
Advertisement
