Advertisement
Quick Links
In-Wall Vessel Lavatory Faucet / Tub Spout
CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED
IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer.
Operating Specifications:
Recommended Supply Pressure: 20 to 70 psi
Maximum Flow Rate: 1.2 gpm for Lavatory Vessel, 7.5 gpm for Tub Spout
Operating pressures between hot and cold supplies should vary no more than 30 psi.
*
If water pressure exceeds 70 psi, install a Pressure-Reducing Valve (PRV).
†
1
INSTALLING SPOUT
•
Prior to installing faucet trim in-wall vessel rough
VALVE (1), must be properly installed and wall
surface must be completely finished
NOTE: Recommended through-hole size shall be Ø1-1/4"
•
Apply thread sealant to both threaded ends of
NIPPLE (2), not supplied, and tighten into center
outlet of VALVE (1)
•
Tighten QUICK CONNECT (3) onto end of
NIPPLE (2) using ½" open-end wrench
•
Confirm QUICK CONNECT (3) is protruding from
finished wall the correct amount with table given
WARNING: Dimension "A" must be met to prevent water damage
Model
MIN "A"
CF-TO-VE302-7
CF-TO-VE302C-7
CF-TO-VE302C-7-77R
TS-E3-E3
D-E3-E3
TS-E3-77
D-E3-77
•
Slide SPOUT ESCUTCHEON (4) onto QUICK
CONNECT (3)
IMPORTANT: To prevent damage to internal o-ring on SPOUT (5),
QUICK CONNECT (3) MUST be free of any dirt and/or debris
•
Slide SPOUT (5) onto QUICK CONNECT (3) and
tighten both SETSCREW (5a) on bottom side of
SPOUT (5)
NOTE: If SPOUT ESCUTCHEON (4) is square, be sure to align it
with SPOUT (5)
CF-TO-VE302-7_ii_190422
Bel Canto
CF-TO-VE302-7, CF-TO-VE302C-7
CF-TO-VE302C-7-77R, TS-E3-E3,
D-E3-E3, TS-E3-77, D-E3-77
Installation Instructions
BY A LICENSED PROFESSIONAL
*†
MAX "A"
1-11/16"
1-7/8"
1-13/16"
1-15/16"
1-13/16"
1-15/16"
1-9/16"
1-3/4"
1-9/16"
1-3/4"
1-11/16"
1-13/16"
1-11/16"
1-13/16"
®
NOTE: Spout installation shown with lavatory
vessel valve, Tub Spout installation is the same
Ø1-1/4"
3
2
A
Tighten with
½" open-end wrench
For Tub Spout
5
5a
1
A
For Lavatory Vessel
A
4
3
Pg 1
Advertisement
Related Manuals for California Faucets Bel Canto CF-TO-VE302-7
Summary of Contents for California Faucets Bel Canto CF-TO-VE302-7
- Page 1 D-E3-E3, TS-E3-77, D-E3-77 In-Wall Vessel Lavatory Faucet / Tub Spout Installation Instructions CALIFORNIA FAUCETS RECOMMENDS THAT ALL PLUMBING PRODUCTS BE INSTALLED BY A LICENSED PROFESSIONAL IMPORTANT: Read all instructions prior to installation and provide copy of instructions to consumer. Operating Specifications: Recommended Supply Pressure: 20 to 70 psi *†...
- Page 2 ALIGN & TRIM VALVE STEM • Remove mudguards from VALVE (1) • To obtain proper HANDLE (7) alignment it may be necessary to re-align cartridge STEM (1b); to align STEM (1b), slightly loosen the cartridge NUT (1d), place HANDLE (7) on STEM (1b) and TIGHTEN in CW direction until desired alignment is achieved;...