Summary of Contents for Feig Electronic OBID i-scan UHF ISC.MRU200
Page 1
MONTAGE INSTALLATION ID ISC.MRU200 MidRange Reader UHF (deutsch / english) final public (B) 2012-03-08 M70201-4de-ID-B.doc...
Page 2
® OBID i-scan Montage ID ISC.MRU200 deutsche Version ab Seite 3 english version from page 28 FEIG ELECTRONIC GmbH Seite 2 von 52 M70201-4de-ID-B.doc...
Page 3
Hinweise jederzeit dankbar. Die in diesem Dokument gemachten Installationsempfehlungen gehen von günstigsten Rahmenbedingun- gen aus. FEIG ELECTRONIC GmbH übernimmt keine Gewähr für die einwandfreie Funktion in systemfrem- den Umgebungen. FEIG ELECTRONIC GmbH übernimmt keine Gewährleistung dafür, dass die in diesem Dokument enthal- tenden Informationen frei von fremden Schutzrechten sind.
4.3.3 Ethernet-Schnittstelle (ID ISC.MRU200-E) ..............16 4.3.4 USB-Schnittstelle (ID ISC.MRU200-USB) ..............17 Eingänge ........................17 Ausgänge ........................19 4.5.1 Optokoppler ........................ 19 4.5.2 Relais ......................... 20 Bedien- und Anzeigeelemente LEDs .......................... 21 T1: Reset-Taster ......................21 FEIG ELECTRONIC GmbH Seite 4 von 52 M70201-4de-ID-B.doc...
Page 5
ID ISC.MRU200 J1-J8: Schnittstellenkonfiguration ................22 X62: Bootloader Modus .................... 23 Technische Daten Zulassung ........................26 6.1.1 Europa (CE) ........................ 26 6.1.2 USA (FCC) ......................... 26 6.1.3 USA und Kanada (UL) ....................27 FEIG ELECTRONIC GmbH Seite 5 von 52 M70201-4de-ID-B.doc...
Obwohl dieses Gerät die zulässigen Grenzwerte für elektromagnetische Felder nicht überschreitet, sollten Sie einen Mindestabstand von 25 cm zwischen dem Gerät und Ihrem Herzschrittmacher einhalten und sich nicht für längere Zeit in unmittelbarer Nähe des Geräts bzw. der Antenne aufhalten. FEIG ELECTRONIC GmbH Seite 6 von 52 M70201-4de-ID-B.doc...
Folgende Komponenten sind im Lieferumfang enthalten: 1 x Reader ID ISC.MRU200 8 x Kurzschlussbrücke (Jumper) 2 x Dichtverschluss M16 1 x Dichtverschluss M12 1 x Dichtverschluss-Reduzierstück 2 x Designblenden aufsteckbar 2 x Integrierte Deckelhalter FEIG ELECTRONIC GmbH Seite 7 von 52 M70201-4de-ID-B.doc...
M5 Stahl verzinkt DIN 84 / ISO 1207, Festigkeitskasse 8.8 oder Beton, Stein z.B. Kunst- stoffdübel 6mm mit Holzschraube DIN96 d=4mm). Der maximale Schraubenkopfdurchmesser be- trägt 8,5 mm 200 (7.87) 182 (7.16) Bild 3-1: Gehäuse ID ISC.MRU200 (alle Maße in mm (inch)) FEIG ELECTRONIC GmbH Seite 8 von 52 M70201-4de-ID-B.doc...
Das beigelegte Dichtring-Reduzierstück ist für die Netzwerkanbindung bzw. das USB- Anschlusskabel vorgesehen. Das aufgeschlitzte Reduzierstück wird über die Netzwerkleitung bzw. das USB-Anschlusskabel gelegt und anschließend in der Kabelverschraubung fixiert. Bild 3-2: Netzwerkanbindung mit Dichtring-Reduzierstück FEIG ELECTRONIC GmbH Seite 9 von 52 M70201-4de-ID-B.doc...
Die Designblenden werden nach der Montage des Readers aufgesteckt. Die Nut an der Längsseite der Blende dient zur Demontage der Blende. Mit einem geeigneten Schraubendreher kann die Blende entfernt werden. Bild 3-4: Designblende FEIG ELECTRONIC GmbH Seite 10 von 52 M70201-4de-ID-B.doc...
Anschlussklemmen und -buchsen In Bild 4-1 und Bild 4-2 sind alle Anschlussklemmen und -buchsen, sowie die Bedien- und Anzei- geelemente für die Readertypen -USB bzw. -E dargestellt. Bild 4-1: Anschlussklemmen und -buchsen (Typ -A) FEIG ELECTRONIC GmbH Seite 11 von 52 M70201-4de-ID-B.doc...
Bei Anschluss der Geräte mit flexiblen Leitungen sind im besondern die Vorschriften nach NEC Artikel 400.7 (8) und Artikel 400.8 (1) – (7) Anzuwenden. Hinweis: Eine Verpolung der Versorgungsspannung kann zur Zerstörung des Gerätes führen. FEIG ELECTRONIC GmbH Seite 12 von 52 M70201-4de-ID-B.doc...
255.255.255.0 Port 10001 Hinweis: Die Reader müssen nacheinander ans Netzwerk angeschlossen und konfiguriert werden. Jede IP-Adresse darf nur einmal im Netzwerk vertreten sein. Alternativ kann die Einstellung über die asynchrone Schnittstelle erfolgen. FEIG ELECTRONIC GmbH Seite 16 von 52 M70201-4de-ID-B.doc...
Bild 4-7: Interne und mögliche externe Beschaltung der Optokopplereingänge Bei Versorgungsspannungen größer 10 V muss der Eingangsstrom durch einen weiteren externen Vorwiderstand (siehe Tabelle 4-8) auf max. 20 mA begrenzt werden. Tabelle 4-8: Externe Vorwiderstände FEIG ELECTRONIC GmbH Seite 17 von 52 M70201-4de-ID-B.doc...
Page 18
Verpolung oder Überlastung der Eingänge führt zu deren Zerstörung. • Die Versorgungsspannung des Readers darf nicht zur Ansteuerung der Eingänge ver- wendet werden, da es ansonsten durch zusätzlich eingestrahlte Störungen zu Einbußen in der Lesereichweite kommen kann. FEIG ELECTRONIC GmbH Seite 18 von 52 M70201-4de-ID-B.doc...
• Die Ausgänge sind für max. 24 VDC / 30 mA ausgelegt. • Verpolung oder Überlastung der Ausgänge führt zu deren Zerstörung. • Die Ausgänge sind nur zum Schalten ohmscher Lasten vorgesehen. FEIG ELECTRONIC GmbH Seite 19 von 52 M70201-4de-ID-B.doc...
• Der Relaisausgang ist für max. 24 VDC / 2 A ausgelegt. • Der Relaisausgang ist nur zum Schalten ohmscher Lasten vorgesehen. Im Falle einer induktiven Last sind die Relaiskontakte durch eine externe Schutzbeschaltung zu schüt- zen. FEIG ELECTRONIC GmbH Seite 20 von 52 M70201-4de-ID-B.doc...
Leuchtet bei einem Fehler im RF-Teil des Readers. Der Fehlertyp kann per Software über die Schnittstellen ausgelesen werden 5.2 T1: Reset-Taster Durch Betätigen des Tasters T1 wird am Reader ein Reset durchgeführt. FEIG ELECTRONIC GmbH Seite 21 von 52 M70201-4de-ID-B.doc...
5-4 ist die Funktion der Stiftleiste X62 beschrieben. Tabelle 5-4: Stiftleiste X62 Beschreibung offen keine Auswirkung nach Betätigen des Tasters T1 wird der Reader in den Bootloader Mo- kurzgeschlossen dus versetzt. FEIG ELECTRONIC GmbH Seite 23 von 52 M70201-4de-ID-B.doc...
- 1 Relais (1 x Wechsler) • Eingänge - 1 Optokoppler max. 24 VDC / 20 mA • Schnittstellen - RS232 - RS485 / RS422 (wahlweise einstellbar) - Ethernet (TCP/IP) (ID ISC.MRU200-E) - USB (ID ISC.MRU200-A) FEIG ELECTRONIC GmbH Seite 24 von 52 M70201-4de-ID-B.doc...
Page 25
• Zulassung Funk - Europa EN 302 208 - USA FCC 47 CFR Part 15 • EN 301 489 • Sicherheit – Niederspannung EN 60950 UL 60950-1 - Human Exposure EN 50364 FEIG ELECTRONIC GmbH Seite 25 von 52 M70201-4de-ID-B.doc...
Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
10.5 dBic. Antennas not included in this list or having a gain greater than 10.5 dBic are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Lists of Antennas: ID.ISC.ANT.U250/250-FCC ID.ISC.ANT.U170/170-FCC ID ISC.ANT.U270/270-FCC ID ISC.ANT.U600/270-FCC FEIG ELECTRONIC GmbH Seite 27 von 52 M70201-4de-ID-B.doc...
Composition of the information in this manual has been done to the best of our knowledge. FEIG ELECTRONIC GmbH does not guarantee the correctness and completeness of the details given in this manual and may not be held liable for damages ensuing from incorrect or incomplete information. Since, despite all our efforts, errors may not be completely avoided, we are always grateful for your useful tips.
25 cm (10 inch) between the device and your cardiac pacemak- er and not stay in the immediate proximity of the device’s antenna for any length of time. FEIG ELECTRONIC GmbH Page 31 of 52...
1 x Reader ID ISC.MRU200 8 x jumper 2 x seal cap M16 1 x seal cap M12 1 x seal cap - reducer 2 x decorative cover, clip-on 2 x integrated cover stays FEIG ELECTRONIC GmbH Page 32 of 52 M70201-4de-ID-B.doc...
DIN 84 / ISO 1207, property class 8.8 or concrete, stone e.g. plastic anchor 6mm with wood screw DIN96 d=4mm). The maximum size of the screw head is 8.5mm (0.33”) 200 (7.87) 182 (7.16) Fig. 3-1: Housing ID ISC.MRU200 (all dimensions in mm (inch)) FEIG ELECTRONIC GmbH Page 33 of 52 M70201-4de-ID-B.doc...
The reducing ring provided is intended for the network connection. The slotted reducer is placed over the network cable and then fixed in place in the cable gland. Fig. 3-2: network connection with slotted reducer FEIG ELECTRONIC GmbH Page 34 of 52 M70201-4de-ID-B.doc...
The decorative covers are attached after installing the Reader. The slot on the long side of the cover is used for disassembling the cover. Use a screwdriver to remove the cover. Fig. 3-4: Decorative cover FEIG ELECTRONIC GmbH Page 35 of 52 M70201-4de-ID-B.doc...
Terminals and Jacks Fig. 4-1 and Fig. 4-2 show terminals, jacks and operating elements of reader type -USB respective- ly reader type -E. Fig. 4-1: Terminals, jacks and operating elements of Type -USB FEIG ELECTRONIC GmbH Page 36 of 52 M70201-4de-ID-B.doc...
Listed NEC Class 2/LPS supply, only. • by use of flexible cords, the NEC rules according article 400.7 (8) and 400.8 (1)-(7) must be applied. Note: Reversing the polarity of the supply voltage may destroy the unit. FEIG ELECTRONIC GmbH Page 37 of 52 M70201-4de-ID-B.doc...
SMA jacks for antenna connections ANT1, ANT2 (input impedance 50 Ω) ANT1 ANT2 Fig. 4-4: Antenna Connections ANT1 and ANT2 Note: The maximum tightening torque of the SMA sockets is 0,45 Nm (4.0 lbf in). FEIG ELECTRONIC GmbH Page 38 of 52 M70201-4de-ID-B.doc...
The readers must be connected to the network and configured one after the other. Every IP- Address must be used only one time. Alternatively this configuration can be done with the asynchronous interface. FEIG ELECTRONIC GmbH Page 41 of 52 M70201-4de-ID-B.doc...
Fig. 4-7: Internal and possible external wiring of the optocoupler inputs For supply voltages of greater than 10 V the input current must be limited to max. 20 mA by an additional external series resistor (see Table 4-8). FEIG ELECTRONIC GmbH Page 42 of 52 M70201-4de-ID-B.doc...
Reversing the polarity or overloading the inputs will destroy them. • The Reader supply voltage must not be used to drive the inputs, since otherwise additionally induced noise may reduce the effective reading range. FEIG ELECTRONIC GmbH Page 43 of 52 M70201-4de-ID-B.doc...
• The outputs are configured for max. 24 VDC / 30 mA. • Reversing the polarity or overloading the outputs will destroy them. • The outputs are intended for switching resistive loads only. FEIG ELECTRONIC GmbH Page 44 of 52 M70201-4de-ID-B.doc...
/ 2 A. • The relay outputs are intended for switching resistive loads only. If an inductive load is used, the relay contacts must be protected by means of an external protection circuit. FEIG ELECTRONIC GmbH Page 45 of 52 M70201-4de-ID-B.doc...
Comes on when there is an error in the RF section of the Reader. LED V4 (red) The error type can be read out via software over the RS232/RS485 interface 5.2 Reset Button Pressing the button T1 resets the reader. FEIG ELECTRONIC GmbH Page 46 of 52 M70201-4de-ID-B.doc...
The pin connector X62 can be closed with a jumper (2.0 mm). Table 5-4: pin connector X62 Description open no effect closed after pressing the button T1 the reader is in th boot loader mode FEIG ELECTRONIC GmbH Page 48 of 52 M70201-4de-ID-B.doc...
- Europe EN 302 208 / EN 300 220 - USA FCC 47 CFR Part 15 • EN 301 489 • Safety - Low-Voltage EN 60950 UL 60950-1 - Human Exposure EN 50364 FEIG ELECTRONIC GmbH Page 50 of 52 M70201-4de-ID-B.doc...
Changes or modifications made to this equipment not expressly approved by FEIG ELECTRONIC GmbH may void the FCC authorization to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
10.5 dBic. Antennas not included in this list or having a gain greater than 10.5 dBic are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Lists of Antennas: ID.ISC.ANT.U250/250-FCC ID.ISC.ANT.U170/170-FCC ID ISC.ANT.U270/270-FCC ID ISC.ANT.U600/270-FCC FEIG ELECTRONIC GmbH Page 52 of 52 M70201-4de-ID-B.doc...