Advertisement
5.
OPERATION
WARNING! Ensure you read, understand and apply Section 1 safety instructions.
5.1.
Assembly
5.1.1. Screw required head onto the tool, holding the spindle with the spanner provided. Only use pads with speed ratings equal to or
higher than the speed rating of the tool.
5.1.2. Connect air supply to tool and press control valve lever (fig.3), releasing the safety catch to check for correct operation.
5.1.3. The air flow may be regulated by the control valve lever.
5.2.
Pinstripe Removal Tool
5.2.1. DO NOT apply excessive pressure, let the tool do the work. Start the tool and bring the edge of the pad to the work surface smoothly and
slowly. Move the tool back and forth in overlapping areas to remove the stripe. Lift the pad from the work surface before stopping the tool.
Regularly check the pad for wear - note minimum diameter marking - and always change a damaged pad.
5.2.2. DO NOT allow tool to run in "idle rotation" for an extended period as this will damage the bearings.
5.2.3. A new pad should be run on a hidden or scrap panel to buff the surface before being used for pinstripe removal.
5.2.4. Before starting each job run the pad on a patch of hidden paintwork to check that no damage is caused.
5.2.5. When used on two pack paints the surface finish may be slightly marked or hazy. Use a high grade cutting compound to restore the surface
finish.
5.2.6. When used on cellulose paints, greater care and time are required to ensure that the minimum of heat is generated. If this care is not
taken, heat will damage the surface finish.
5.2.7. The tool will also remove the double sided tape used to attach body trim. This process is slower than stripe removal and may produce an
unpleasant odour.
5.3.
Wire Brush
5.3.1. To change the wire brush, remove the centre screw with a 4mm hex bit (fig.4).
5.3.2. Remove the end cap (fig.5) and slide the wire brush band from the spindle.
5.3.3. Slide the replacement wire brush over the spindle and secure with the end cap.
5.3.4. Replace the centre screw.
fig.4
6.
MAINTENANCE
WARNING! Disconnect the tool from air supply before changing accessories, servicing or performing maintenance. Replace or repair
damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
6.1.
If the air supply system does not include an oiler, lubricate the air tool daily with a few drops of good grade air tool oil such as Sealey
ATO/500 or ATO1000, dripped into the air inlet before use.
6.2.
Clean the tool after use and change pads when required.
6.3.
Loss of power or erratic action may be due to the following:
a) Excessive drain on the air line. Moisture or restriction in the air pipe. Incorrect size or type of hose connectors. To remedy check the air
supply and follow instructions in Section 4.
b) Grit or gum deposits in the tool may also reduce performance. If your model has an air strainer (located in the area of the air inlet),
remove the strainer and clean it. Flush out the tool with gum solvent oil or an equal mixture of SAE No 10 oil and kerosene. Allow to dry
before use.
If you continue to experience problems, contact your local Sealey service agent.
6.4.
When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Parts support is available for this product. To obtain a parts listing and/or diagram,please log on to www.sealey.co.uk,
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack Sealey Limited
Environmental Protection
email sales@sealey.co.uk or telephone 01284 757500.
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park,
Bury St. Edmunds, Suffolk,
IP32 7AR
riginal Language Version
O
fig.5
01284 757500
01284 703534
www.sealey.co.uk
sales@sealey.co.uk
SA695
Issue: 1 - 03/12/14
Advertisement
