Summary of Contents for XMA Viglen Omnino Pro
- Page 1 Omnino Pro Assembly Guide v1.1 – July 2019 Viglen Personal Computers are manufactured by XMA in the UK Unrestricted/Public...
- Page 2 The information in this document is subject to change without notice. Nothing herein should be construed as constituting an additional warranty. XMA shall not be liable for technical or editorial errors or omissions contained herein. XMA limited Company makes no warranty of any kind regarding this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
-
Page 3: Table Of Contents
Optional Security Pillar Kit ........................21 Assembly of Security Pillar Kit (Part 1) ....................22 Assembly of Security Pillar Kit (Part 2) ....................23 Overview of fully Assembled Security Pillar ..................24 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... - Page 4 Replacing the Display Back light Cable....................47 20 Removing Web Cam module ................48 20.1 Replacing the Web Cam module ......................49 21 Removing the Optical Drive from the computer ........... 50 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved...
- Page 5 Spare Parts list in detail (Part 3) ......................57 23.4 Screw details (Part 1) .......................... 58 23.5 Screw details (Part 2) .......................... 59 24 Getting Support for your Viglen Product ............60 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved...
-
Page 6: Document Control
Date Revision Reason for Revision Initial draft 24/07/2019 Initial Release 31/07/2019 Corrections with package contents details and format. 1.2 References Reference # Reference 1.3 Abbreviations and Acronyms Abbreviation Description 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 7: Regulatory, Safety, Environmental And Configuration Information
NOTICE: XMA recommend customers do not carry out maintenance on the Viglen Omnino Pro; if it is done incorrectly customers may damage the main board or other components. NOTICE: Before you start working on the Viglen Omnino Pro please ensure you have all the necessary tools as listed Below. - Page 8 Adjustment of the volume control as well as the equalizer to other settings than the centre position may increase the ear-/headphones output voltage and therefore the sound pressure level. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved...
-
Page 9: Environmental Notices
2.3 Environmental notices Product Design XMA’s products are designed to ensure that all our equipment can be dismantled, and the components and materials are recoverable. WEEE Marking All XMA’s products that are subject to the WEEE directive shipped from 13th August 2005 are compliant with the WEEE marking requirement. -
Page 10: Recommended Tools
3. Replace any media cards, discs, or any other parts that you removed before working on your computer. 4. Connect your computer and all attached devices to their electrical outlets. 5. Turn on your computer. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 11: Setting Up Your Omnino Pro
Panel Configuration Active area: 527.04mm (H) x 296.46mm(V) Panel Resolution: 1,920 x 1,080 Display colours: 16.7M colours Display model: Normally Black Surface Treatment: Anti-Glare, 3H 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 12: Package Contents
The following accessories are included in the box. Please check against your order to see if they are enclosed with the All-in-one. If anything is missing or damaged, please contact support team. keyboard, mouse and accessories parts are for reference only. Actual products specification may vary. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 13: System Overview
6 System Overview 6.1 Front View one some model of system board, the on-screen-display (OSD) for brightness indicator may function in reverse order to engraved brightness button on the panel. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 14: Rear View (Right-Hand Side)
6.2 Rear View (right-hand side) USB Type-C Port is NOT active, this feature is for future release of system board model. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 15: Rear View (Left-Hand Side)
6.3 Rear View (left-hand side) Image for illustration purposes, actual products specification may vary. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 16: Rear View (Under-Side)
6.4 Rear View (Under-side) Image for illustration purposes, actual products specification may vary. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 17: System Overview (Internal)
7 System Overview (Internal) Image for illustration purposes, actual products specification may vary. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 18: Stand Base Assembly
3. Use the ‘thump screw’ to tighten the screw located at the bottom of the base. The Thump screw and stand cable tie is included with stand accessories pack. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 19: Fitting Of Base Stand
• Unplug the monitor if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your monitor. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 20: Removing The Base Stand
Place the unit face down on a smooth surface. Pay attention not to damage the screen. Press the quick release button down to release the stand. Left the stand way and place it somewhere safe. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 21: Optional Security Pillar Kit
8.3 Optional Security Pillar Kit The dedicated security pillar for the Viglen Omnino Pro provides an effective theft deterrent without compromising the versatility of the Omnino Pro. Spare Part number Description E07SPL01 Security Pillar for Omnino Pro (2019) ESPADL06 30mm Security Padlock... -
Page 22: Assembly Of Security Pillar Kit (Part 1)
Remove the original fixed metal plate from the stand raiser by removing the four screws. Assemble the pillar with security fixed metal plate (C). Secure the pillar assembled in step 2 to the stand raiser using four screws. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 23: Assembly Of Security Pillar Kit (Part 2)
4. Feed the security pillar with chassis attached through the hole on the desired desk. 5. Secure it with pillar washer and pillar nut 6. Use padlock to secure the unit. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 24: Overview Of Fully Assembled Security Pillar
8.6 Overview of fully Assembled Security Pillar Security pillar can only support 30mm padlocks. Anything greater is not supported by the security pillar. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 25: Optional Height Adjust Stand
Put a piece of soft cloth on the table beforehand to prevent the stand from being scratched. Hold the Stand raiser and push the Stand-Base (B). Use the ‘stand base screw’ provided to secure stand base to stand riser. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 26: Height Adjust Stand Assembly (Part 2)
2. Hold the stand with both hands. 3. Gently line the stand to the VESA mount area until , aligning the screw holes. 4. Secure the stand with four long VESA screws 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 27: Removing The Height Adjust Stand Base Assembly
1. Place the screen face down on a smooth surface. Pay attention not to scratch or damage the screen. 2. Remove the four VESA screws. 3. Lift the monitor stand off the computer base. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 28: Removing The Rear Cover (Part 1)
1. Using caution, lay the Omnino Pro down on a flat surface covered with a soft cloth 2. Push the quick release button down to release the stand. 3. Gently lift the base stand off from the computer base. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 29: Removing The Rear Cover (Part 2)
Using caution, lay the Omnino Pro down on a flat surface covered with a soft cloth. Remove the screws that secure the base cover. Gently lift the back cover ensuring to disconnect webcam module connector from the system board. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... - Page 30 To disconnect the Webcam connector, lift the back cover halfway to access the webcam connector from the system board USB2.0 header before lifting the back cover fully. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved...
-
Page 31: Replacing The Rear Cover
1. Align the slots on the back cover with the tabs on the display bezel and snap the back cover into place. 2. Secure the back cover with screws. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 32: Stand Security - Quick Release Button
2. To enable the quick release button, remove the standard or T10 Screw. The standard quick release button screw is included with stand accessories pack. Labelled ‘base snap screw’. T10 security screw is an optional screw. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 33: Removing The System Board
2. Disconnect all cables from the system board. 3. Remove the four Hexagonal screw for EMI shield. 4. Gently lift the motherboard out from the chassis base. 5. Remove the system board IO shield. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 34: Replacing The System Board
NOTE: Before system board is positioned into the chassis please check CPU thermal bracket is attached on the system board. Without the thermal bracket, thermal module cannot be secured. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 35: System Board Jumper Settings
12.2 System board Jumper settings Please refer to motherboard manual for location of jumpers for display panel backlight and display panel VCC power. The Viglen Omnino Pro supports following jumper settings. Product Display panel backlight Display panel VCC power (3-pin BLKT_PWR_SEL) -
Page 36: System Board Jumper Settings For Different Models
12.3 System board Jumper settings for different models Motherboard 3 Pin BLKT PWR SEL Notes Vig855S Vig790S Vig791S Vig870G Motherboard LCD VCC Power Notes Vig855s Vig790S Vig791S Vig870G 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 37: Removing The Heatsink
2. In sequential order (indicated on the heat sink), loosen the captive screws that secure the heat sink to the system board. 3. Lift the heat sink off the system board and chassis. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 38: Replacing The Heat Sink
1. Align the captive screws on the heat sink with the screw holes on the system board. 2. In sequential order (indicated on the heat sink), tighten the captive screws that secure the heat sink to the system board and chassis. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 39: Removing The Fan
1. Align the screw holes on the fan with the screw holes on the computer base. 2. Replace the screws that secure the fan to the computer base. 3. Connect the fan cable to the system board. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 40: Removing Internal Power Board
5. Lift the power board, along with its cable, off the computer base. 4PIN convert to 2PIN DC cable NOTE: Please ensure 4Pin converter to 2Pin DC cable is used, this cable should not be discarded. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 41: Replacing The Internal Power Board
NOTE: Please ensure 4Pin converter to 2Pin DC cable is used, this cable should not be discarded. When replacing the power module transfer the 4pin to 2pin DC cable to new mower module. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 42: Removing The Usb And Audio Pcba
2. Align the PCB board with the screw holes on the system board. 3. Tighten the screws that secure the PCB board to chassis. 4. Reconnect all the cables. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 43: Removing The Power-Button Module
2. Slide the power-button module into the slot on the display bezel. 3. Route the power-button module cable through its routing guide. 4. Replace the two screw that secures the power-button module. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 44: Removing The Inverter Board
3. Gently disconnect the cables from the Inverter board. 4. Lift the inverter board off chassis. NOTE: Note the orientation of the converter board so that you can replace it correctly. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 45: Replacing The Inverter Board
5. Replace the screws that secure EMC shield and Inverter board to the chassis. NOTE: Ensure that LCD display brightness panel cable is connected correctly on the inverter board. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 46: Removing Display Back Light Cable
2. Gently push the IO shield holder in the direction of the arrow. 3. Peel off the tape from the chassis 4. Press the securing clips and disconnect display-backlight cable from the display panel. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 47: Replacing The Display Back Light Cable
NOTE: Ensure that no cables are placed under the display panel. 4. Secure the IO shield holder by sliding in and aligning with the screw holes. 5. Secure the IO shield holder with screws. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 48: Removing Web Cam Module
3. Remove the screws that secure the camera assembly to the rear cover. 4. Carefully lift the camera assembly from the rear cover. NOTE: Note the orientation of the camera assembly so that you can replace it correctly. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 49: Replacing The Web Cam Module
2. Align the notch on the camera module with the rear cover. 3. Replace the screws that secure the camera assembly to the rear cover. 4. Adhere the foil over the camera assembly. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 50: Removing The Optical Drive From The Computer
2. Remove the screws that secure the Optical drive assembly to the computer base. 3. Lift the optical drive assembly off the computer base. 4. Replace the Optical drive blanking plate computer base. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 51: Removing The Optical Drive From The Assembly
2. Gently pull the optical drive out. 21.2 Removing the Optical drive blanking plate Remove the screws that secure the optical drive plate. Reinstall new blanking optical drive plate. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 52: Removing 2.5' Hard Disk Drive
2. Lift the hard-drive assembly off the optical drive base. 3. Remove the screws that secure the hard-drive bracket to the hard drive. 4. Lift the hard-drive bracket off the hard drive. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 53: Installing 2.5" Hard Disk/Ssd Drive
6. Connect data and SATA data and power cable to the system board. Caution: Please note Ominio pro is configured with m.2 storage devise as standard. The optical drive kit and 2.5” brackets are optional. 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 54: Spare Parts List Table
23 Spare Parts List Table Part code Description BPC70231 Viglen Omnino Pro 23.8’’ All-in-One PC PPG0M701 150Watts Power Supply for Omnino Pro (2019) PARP0701 USB and Audio PCB for Omnino Pro (2019) PAFP0711 Inverter Board for Omnino Pro (2019) PCPMA018... -
Page 55: Spare Parts List In Detail (Part 1)
23.1 Spare Parts list in detail (Part 1) PPG0M701- 150Watts Power Supply for Omnino Pro (2019) BPC70231 Viglen Omnino Pro 23.8’’ All-in-One PC PAFNNPAK -Heat Sink for Omnino Pro (2019 4Pin to 2Pin converter cable for DC VPAM0701 Stand for Omnino Pro (2019) VPAM06H1 Height Adjust Stand for Viglen Omnino (2017) ESPADL06 –... -
Page 56: Spare Parts List In Detail (Part 2)
4PIN L: 120mm R: 430mm LEAD-FREE - 263 Mainboard EMI metal shield Inverter board EMI metal shield Omnino Pro Back cover material ABS HDD bracket (SECC) T=0.8mm Natural colour 536.8*326.4*46.7mm Black LEAD-FREE 15.6.99.0035994-571 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 57: Spare Parts List In Detail (Part 3)
4PIN L: 120mm R: 430mm LEAD-FREE - 263 - 546(SY-W4PE8165B400C-L01) 15.2.08.0063991-D66 15.3.02.2052011-546 WIFI right Antenna (M.2) Grey USB3.0 cable WIFI right Antenna (M.2) Grey L=400±5mm USB 3.0 Cable Line length L=550±5mm LEAD-FREE- LEAD-FREE - 546(SY-W4PE8165G400C-L01) 15.3.09.0027991-D65 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 58: Screw Details (Part 1)
M2.0*4(L)*5.0(P)*0.8(T)mm Cross flat head countersunk head Self-tapping 15.6.02.0110991-587 Base fixing plate *4 Base fixing plate *4 Screw M4.0*5(L)*7.0(P)*2.3(T)mm Cross countersunk head Nickel plated + chrome Screw M4.0*6(L)*8.0(P)*1.5(T)mm resistant + hardened 15.6.02.0063991-587 14.2.03.0027997-587 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 59: Screw Details (Part 2)
Screw PB3 * 8 (P) (L) * 5.5 * 2.0 mm (T) tail UARSAV10 4x VESA 14mm Long Screw for Height black zinc plated cross pan head triangle self- tapping dental LEAD - FREE – 587 Adjust Stand * 15.6.02.0047991-587 0115 846 4000 info@xma.co.uk © 2019 XMA Ltd. All Rights Reserved... -
Page 60: Getting Support For Your Viglen Product
Images shown are for illustrative purposes only. Although XMA endeavours to ensure the accuracy of this information, XMA cannot be held liable for any damages whatsoever for errors or omissions of fact herein. Viglen is a trademark of XMA Ltd, XMA Ltd is a subsidiary of Viglen Technology Ltd.