Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Fluid Gaming EK-AC Radeon RX 5700 +XT
- Page 1 1st Revision, Sep 25th 2019 EK-AC Radeon RX 5700 +XT USER GUIDE...
-
Page 2: Table Of Contents
TABLE OF CONTENT IMPORTANT INFORMATIONS GENERAL INFORMATIONS PREPARING YOUR GRAPHICS CARD INSTALLING THE WATER BLOCK INSTALLING THE BACKPLATE INSTALLING THE FITTINGS AND TUBING CONNECTING THE D-RGB LED STRIP SUPPORT AND SERVICE SOCIAL MEDIA / 2 /... -
Page 3: Important Informations
IMPORTANT INFORMATIONS This product is made from aluminum and can be only used This product is intended for installation by expert users. Please consult a qualified technician for installation. Improper installation with other aluminum liquid cooling components, such as Al may result in damage to your equipment. -
Page 4: General Informations
GENERAL INFORMATIONS CONTENT: - EK-AC Radeon RX 5700 +XT waterblock - Mounting screws - Thermal pads REQUIRED TOOLS: - Scissors - Phillips head screwdriver - Optional: pliers BAG CONTENT: Bag content is universal for all water blocks, you may not need all screws. -
Page 5: Preparing Your Graphics Card
PREPARING YOUR GRAPHICS CARD STEP 1 REMOVING THE FACTORY PROVIDED BACKPLATE Remove all encircled screws using a Phillips head screwdriver, then take off the backplate. Save these screws for later. You will need them when reinstalling the backplate. STEP 1 STEP 2 REMOVING THE STOCK COOLER Remove the remaining screws as shown below. - Page 6 STEP 3 CLEANING THE PCB Wipe off the remains of any thermal compound from the GPU core by using a non-abrasive cloth or q-tip. EKWB recommends the use of denatured alcohol for removing TIM leftovers. Additionally, remove all of the stock thermal pads from both sides of the PCB.
- Page 7 STEP 5 CUTTING THERMAL PADS 1: Thermal Pad E – 0.5 mm Your block is supplied with thermal pads that need to be cut into smaller pieces in order to cover all VRM components. PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION. Replacement thermal pads: 2: Thermal Pad F –...
-
Page 8: Installing The Water Block
INSTALLING THE WATER BLOCK STEP 1 PLACING THE BLOCK ON TO THE GRAPHICS CARD Carefully position the water block with preinstalled standoffs on to the graphic card. During this process please make sure you align mounting holes on the PCB with holes on the water block. Also pay attention not to use too much force. STEP 1 STEP 2 ATTACHING THE BLOCK TO THE GRAPHICS CARD... -
Page 9: Installing The Backplate
INSTALLING THE BACKPLATE Take six mounting countersunk screws (M2.5x8) that you have already removed from the backplate and install them as shown in the picture. Screw M2,5x8 Tighten the screws with the Phillips head screwdriver. INSTALLING THE FITTINGS AND TUBING Screw in the two G1/4 threaded male fitting. -
Page 10: Connecting The D-Rgb Led Strip
CONNECTING THE D-RGB LED STRIP Plug the 4-pin connector from Water block’s D-RGB LED light to the DRGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, empty, Ground. Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. -
Page 11: Support And Service
SUPPORT AND SERVICE For assistance please contact: http://support.ekwb.com/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...