Download
Share
Print this page
  1. Manuals
  2. Brands
  3. YLP Manuals
  4. Flashlight
  5. Unicorn 1.0
  6. Complete turning instructions

YLP Unicorn 1.0 Complete Turning Instructions

Hide thumbs
1
2
3
4
5
6
7

Advertisement

Quick Links

Download this manual
COMPLETE TUNING INSTRUCTIONS FOR THE FLASHLIGHT
CONTENTS
1. General principles of operating and settings
1-1. Engineering menu
1. GENERAL PRINCIPLES OF OPERATING AND SETTINGS
Customization of the Unicorn flashlight operation implies following configuration options:
- bringing to the main menu particular additional options (stroboscope, button lock,
beacon, button backlight, battery check, tactical mode, additional custom mode);
connecting the option with particular command («slot»).
- bringing to the main menu particular options of user interface changing (smooth or
discrete adjustment, memory of modes - on/off, button backlight in the off and on
state); connecting the option with particular command («slot»).
Commands are configured through the engineering menu. (pt 1-1, 1-2).
Green LED in the button indicates confirmation of the command execution or turning on
the function; Red LED indicates disabling of the function (for example, memory of modes
or button backlight).
Engineering menu also allows:
- quickly switch between three pre-configured user interfaces (pt 1-3);
- save the current settings configuration as one of the pre-configured user interfaces (pt
1-4);
- set up thermal control of the flashlight (pt 2-1, 2-2).
1-1. Engineering menu
To access the engineering menu screw the cap until tight while holding the button.
To exit the engineering menu de energize the flashlight (unscrew the cap).
CAUTION!
Before de energizing, make sure that the ashlight is turned o FULLY (button backlight has
gone out or has switched to the permanent mode). Otherwise, unsaved data will be lost!

Advertisement

loading

Related Manuals for YLP Unicorn 1.0

Summary of Contents for YLP Unicorn 1.0

  • Page 1: Table Of Contents

    1-4. Changing of preconfigured user interfaces 2. Thermal control settings 2-1. Manual thermal control setting 2-2. Temperature sensor calibration 3. Some particular qualities of Unicorn 1.0 3-1. Battery check and indication 3-2. Basic features of adjustment 3-3. Smooth adjustment features 3-4.

  • Page 2: Configuration And Settings Of Slots (Commands)

    Available engineering menu commands: 7 clicks +hold – enable slot setting mode. 8 clicks – turn off slot setting mode. 9 clicks +hold – thermal control settings. 13 clicks + hold – set current configuration as UI 1. 14 clicks – download UI 1 15 clicks +hold –...

  • Page 3: Preconfigured User Interfaces

    For example, you want to set the battery check function to “4 clicks” command: - enter the engineering menu (screw the cap until tight while holding the button); - enable slot setting mode (7 clicks +hold), the button will ash green; - execute the “4 clicks”...

  • Page 4: Changing Of Preconfigured User Interfaces

    1-4. Changing of preconfigured user interfaces If needed, you can customize a configuration of settings and save it instead of any of three UIs. If current configuration was not saved, it will be lost. For example, you con gured the functions you need, and now you want to save current con guration as UI 1: - enter the engineering menu (screw the cap until tight while holding the button);...

  • Page 5: Thermal Control Settings

    2. THERMAL CONTROL SETTINGS Unicorn is equipped with active thermal control system that changes brightness depending on the degree of heating of the flashlight. The flashlight is already set up for comfortable work, temperature threshold is 50°C; sensor is calibrated at room temperature of 25°C.

  • Page 6: Some Particular Qualities Of Unicorn

    3. SOME PARTICULAR QUALITIES OF UNICORN 1.0 3-1. Battery check and indication Battery charge indication is implemented using the button backlight: Green – battery is almost full (voltage higher than 3.8V). Green + red – average charge level (voltage higher than 3.5V).

  • Page 7: Discrete Adjustment Features

    3-4. Discrete adjustment features - Brightness levels switches upward with holding the button. When the maximum or the minimum brightness level is reached, the direction changes (after a small pause). - The “click-and-hold” command can be also used for changing the direction of the adjustment.