Advertisement
P Maintenance instructions ProtoMat S-Serie
the X and Y axes: ........................................................................ 1
2. Maintenance of the Z axis guide:............................................... 5
4. Maintenance of the collet ........................................................... 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for LPKF ProtoMat S Series
- Page 1 P Maintenance instructions ProtoMat S-Serie 1. Maintenance of the transport spindles and linear guides for the X and Y axes: ................ 1 2. Maintenance of the Z axis guide:..........5 3. Maintenance of the working depth limiter and the collet..7 4.
-
Page 2: Maintenance Of The Transport Spindles And Linear Guides For The X And Y Axes
Maintenace ProtoMat S-Serie 1. Maintenance of the transport spindles and linear guides for the X and Y axes: Tools required: Torx 27 Maintenance kit Art. Nr.: 126891 für S100; 126892 für S42/S62 Accessory pack ProtoMat Supplied as standard Required: Brush Ball bearing grease Depth limiter grease Plastic nut grease... - Page 3 Maintenace ProtoMat S-Serie • Close the cowling of the cross member and the hatch in the cover, and run the head of the miller 310 mm to the right with the BoardMaster. • Open the hatch and use the brush to smear some plastic nut grease onto the transport spindle to the left of the spindle nut.
- Page 4 Maintenace ProtoMat S-Serie • Remove the two marked screws (Torx 27), and pull the cover plate to the front and out of the machine. • Use the brush once more to pick up some ball bearing grease, and apply grease to the linear guides (2 and 3).
-
Page 5: Maintenance Of The Z Axis Guide
Maintenace ProtoMat S-Serie 2. Maintenance of the Z axis guide: Tools required: none Maintenance kit Art-Nr. 126891 für S100, 126892 für S42/S62 Accessory pack ProtoMat Supplied as standard Required: Machine oil • Run the head of the miller into the middle of the operating area, and stop the BoardMaster. Do not run the machine to the reference point. - Page 6 Maintenace ProtoMat S-Serie • The gray tip must be fitted onto the syringe. Use the syringe to apply a few drops of machine oil to the guides. • Switch the machine back on, and start the BoardMaster software. The machine will lift the head of the miller back up again, and run it slowly to the reference point.
-
Page 7: Maintenance Of The Working Depth Limiter And The Collet
Maintenace ProtoMat S-Serie 3. Maintenance of the working depth limiter and the collet Tools required: Torx10; Torx 20 Maintenance kit Art-Nr. 126891 for S100, 126892 for S42/S62 Accessory pack ProtoMat Supplied as standard • Make sure that the collet is not holding any tools. Run the milling head 150 mm to the right of the 0 position. -
Page 8: Maintenance Of The Collet
Maintenace ProtoMat S-Serie 4. Maintenance of the collet Tools required: Collet key, collet brush, any drill or milling tool with an 1/8" shaft Accessory pack ProtoMat Supplied as standard • The inside of the collet can be cleaned at any time without having to dismantle it first. Do this by opening the collet in Service mode, and pushing the collet brush into the opened collet. - Page 9 Maintenace ProtoMat S-Serie • Turn the collet key to the left to loosen the collet. After turning a few times, the tool with the collet can be pulled downwards, and out of the milling head. • Remove the tool from the collet, and clean the inside of the collet with the collet brush. •...
Need help?
Do you have a question about the ProtoMat S Series and is the answer not in the manual?
Questions and answers