Summary of Contents for CHIEF CHF1001
- Page 1 OWNER'S MANUAL l CHF1001, 7´ Arm Extractor • CHF1002, 10´ Arm Extractor Chief Fume Extractor...
- Page 2 For quick future reference, complete the system and filter information in the spaces below. Should you need assistance, call the Chief customer service number shown below. To expedite your service, have the following information available when contacting Chief Automotive Technologies.
-
Page 3: Table Of Contents
TABLE OF CONTENTS Page 1.0 ImPortant notIce ......................1 2.0 IntroductIon ........................1 2.1 descrIPtIon and oPeratIon .................. 1 3.0 Product safety GuIdelInes ..................1 4.0 system sPecIfIcatIons ....................2 5.0 InstallatIon ........................2 5.1 equIPment off loadInG and InsPectIon ............2 5.2 InstallatIon safety .................... - Page 4 SAFETY PRECAUTIONS we have provided many important safety messages in this manual on your w series fume extraction equipment. always read and obey all safety messages. this is the safety alert symbol. this symbol alerts you to potential hazards that can kill or hurt you and others. all safety messages will follow the safety alert symbol and the word “danGer”...
- Page 5 SÉCURITÉ SÉCURITÉ Nous avons fourni des messages de sécurité importants dans ce manuel sur votre W-Series de matériel d'extraction des fumées. Toujours lire et respecter tous les messages de sécurité. Nous avons fourni des messages de sécurité importants dans ce manuel sur votre W-Series de matériel d'extraction des fumées.
-
Page 6: Important Notice
FIGURE 1 call your local chief representative, or visit our website General Product Operation at www.chiefautomotive.com for more information. 2.1 DESCRIPTION AND OPERATION the fume extractor is designed to provide high 3.0 PRODUCT SAFETY GUIDELINES... -
Page 7: System Specifications
® revised 04/15 fume extractor 4.0 SYSTEM SPECIFICATIONS WARNING 5.0 INSTALLATION • The system should not be powered or operated the fume extractor is portable system that can be configured with multiple accessories to serve various without the extraction arm properly installed on the application requirements. -
Page 8: Electrical Installation
® revised 04/15 fume extractor 4. locate gas spring and spring mounting pins in loose 8. Install the flex duct onto the base and middle joints parts kit box. the mounting pins should be taped to using the split clamps provided. the middle and base the lid of the box. -
Page 9: Unit Operation
® revised 04/15 fume extractor 6.3 LOCATING ExTRACTION HOOD 6.0 UNIT OPERATION WARNING 6.1 POWER SWITCH • Do not place the system on a sloped surface or in each fume extractor has a main power switch that an area where the unit will be prone to tipping. -
Page 10: Extraction Arm Damper
® revised 04/15 fume extractor the position of the extraction hood is critical to the 7.0 USER SERVICING INSTRUCTIONS overall performance of the fume extraction system. the extraction arm and hood are designed to provide maximum flexibility and convenience in operation. the DANGER 360°... -
Page 11: Adjusting Extraction Arm Joints
® revised 04/15 fume extractor 4. slide the filters out of the fume extractor and transfer be facing downward. to close the filter access door, to a suitable disposal container. push the door handle upward, toward the unit. the filter access door handle must be in a perpendicular 5. -
Page 12: Spark Arrestor
® revised 04/15 fume extractor recommended to fine tune the desired movement. an impingement spark arrestor is located at the inlet of the fume extractor immediately below the base of to adjust the hood joint swivel assembly, follow the the extraction arm. -
Page 13: Motor Supplementary Protection
® revised 04/15 fume extractor 7.4 MOTOR SUPPLEMENTARY PROTECTION 7.5 ROUTINE MAINTENANCE WARNING WARNING • Disconnect the power prior to servicing the • Disconnect electrical power prior to servicing equipment. equipment. • Take all necessary precautions including protective the fume extraction units are equipped with a manually... -
Page 14: Troubleshooting Guide
® revised 04/15 fume extractor Quarterly Items: • Verify that the serial and warning labels are all readable and undamaged. clean or replace as required. • Inspect the spark arrestor for any accumulated material or fume and clean as necessary. -
Page 15: Replacement Parts
® revised 04/15 fume extractor 9.0 REPLACEMENT PARTS 9.1 FUME ExTRACTOR REPLACEMENT PARTS reserved space for fume extractor replacement parts table to be created by vsG. 61-10085 FIGURE 7 Fume Extractor Replacement Parts Detail... -
Page 16: Extraction Arm Replacement Parts
® revised 04/15 fume extractor 9.2 ExTRACTION ARM REPLACEMENT PARTS 61-10081 FIGURE 8 Extraction Arm Replacement Parts... -
Page 17: Wiring Diagram
® revised 04/15 fume extractor 10.0 WIRING DIAGRAM WIRING DIAGRAM 04-001493... - Page 18 this page intentionally left blank...
- Page 19 this page intentionally left blank...
- Page 20 Fume Extractor which do not perform satisfactorily due to defect caused by faulty material or workmanship. Chief’s obligation under this warranty is limited to the repair or replacement of products which are defective and which have not been misused, carelessly handled, or defaced by repair or repairs made or attempted by others.
Need help?
Do you have a question about the CHF1001 and is the answer not in the manual?
Questions and answers