Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Nordic Radio Ping 6
- Page 1 Ping ™ User manual...
- Page 2 For details, see the warranty certificate. Hereby, Benefon Oyj declares that this tracking device, type TP00310/TP00320 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. • FCC warning statements: This device complies with part 15 of the FCC Rules. Operation is subject to following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance would void the user’s authority to operate the equipment. • Ping 6 is a registered trademark of Nordic Radio. 0413 Note: Correct disposal of this product: The tracking device should not be disposed with household or other commercial wastes. Remove the battery from the phone Made in Finland and dispose it according to local battery for Nordic Radio recycling laws. www.gsmlarm.se...
-
Page 3: Table Of Contents
Removing battery and back cover..6 Config 15: Max allowed movement Keys, LEDs and outer parts......6 in.anchor.mode........14 Turning Ping 6 on and off......7 Messaging settings........ 14 Status LEDs..........7 Config 23-24: Destination numbers..14 Charging the battery........ 8 Voice call settings........ -
Page 4: Ping™ 6
Ping™ 6 Getting started Ping™ 6 is an auxiliary device for locating and Inserting SIM-card tracking different targets. Place Ping™ 6 on your desired target, e.g car, and you can easily monitor it’s location. Ping™ 6 can send you continuously updated position messages. With these messages, you can easily track the movements of Ping™ 6. You can also create an anchor that alarms you if your Ping™ 6 is moved outside your defined area. You can call or send messages to Ping™ 6 to get an updated position at any time. Additionally, by making a voice call, you can also listen to what happens nearby the device. Ping™ 6 is a GSM-device with in-built GPS- positioning and support for MPTP commands. It can be used with any corresponding Benefon GPS-GSM phones and back-end devices that also support MPTP commands. -
Page 5: Inserting Battery And Back Cover
1. Remove the back cover and battery as described in on page 6. 2. Slide the SIM card holder to the right. Lift the holder into an upright position. 3. Insert SIM card into the hole. Check that the cut corner is placed at the bottom left corner. 4. Close the holder. Slide the holder back to the left until it locks. Inserting battery and back cover 1. Place the bottom tabs of the battery into the small hollows at the bottom of the device. 2. Push the battery towards the device until it locks into place. Ensure that the battery release catch is positioned upwards. 3. Place the back cover towards the device, bottom first. 4. Press the cover to the device until it locks in place at the top. Note that the battery will reach its full capacity 5. Fasten the back cover with the fastening only after two or three complete charges. For screws. Longer screws for the front and more info, see Charging the battery on page 9. shorter for the back side. -
Page 6: Removing Battery And Back Cover
Keys, LEDs and outer parts Removing battery and back cover 1. Remove the fastening screws by using the screwdriver included in Locator sales package. 2. Remove the back cover by lifting it off front side first. 3. Remove the battery by pressing the battery release catch downwards and lifting the battery off. -
Page 7: Turning Ping 6 On And Off
Turning Ping™ 6 on and off You can ask the battery status by pressing the power on/off button. The status LED indicates You can turn Ping™ 6 on by pressing the power battery level as follows: on/off button. As a sign of starting-up, all three LED indicators turn on for a couple of seconds. Blinks/ After that the status LED continues blinking for sequence Battery status about 20 seconds. To turn the device off, press Low (0-20%) the power on/off button again. Fairly low (21-40%) Status LEDs Fairly full (41-60%) When Ping™ 6 is turned on, LED indicators Almost full (61-80%) express the status of the device as follows: Continuously on Full (81-100%) When battery is low, Ping™ 6 also sends battery Indicator light alarm message to your defined destination GSM LED Continuously on, when data call is on, numbers. -
Page 8: Charging The Battery
Charging the battery to the ongoing mode, instead of showing the charging status. 1. Plug the charger cable in the bottom connector of the device (round hole on the lefthand side). 2. Plug the charger into the mains outlet. 3. Charging starts automatically. As a sign of charging, all three LED indicators are turned on for a couple of seconds. After that the GSM LED blinks in sequences, 2 blinks in a sequence at first and then 4 blinks in a sequence. When the battery is fully charged, the GSM LED stays constantly on until the charger is disconnected. If there is an interruption or failure in charging, the status LED is turned off. Unplugging and replugging the cable displays the status of charging. If the battery is full, the status LED blinks 4 times, after which it’s turned off. 4. You can operate Ping™ 6 during charging. However, if the battery is totally empty, it might take several minutes before the device can be used. If you turn the Locator on while charging, the LEDs indicate events related... -
Page 9: Features
Features Anchor Each function is confirmed with a short vibration. Anchor mode can be used to anchor Ping™ 6 to a defined position. In anchor mode, Ping™ 6 Stand-by mode is continuously calculating it’s position and When Ping™ 6 is turned on, it enters into comparing it with the position it had when the stand-by mode. While in the stand-by mode, the anchor mode was entered. device is not activated on any process but is Anchor mode is switched to alarm mode if ready to receive and answer location requests. Ping™ 6 moves further than allowed from Stand-by mode is left when another mode is it’s original position. You can set the alarm activated. triggering distance by defining maximum allowed movements in configuration. For Positioning more information, see Config 15: Max allowed Positioning is activated by sending PING a... -
Page 10: Alarm
Alarm button at the same time for 3 seconds. When the mode is activated NMEA data sending is Alarm mode is activated, when the alarm button started. If you want to leave the NMEA mode, is pressed and held down for 3 seconds. If there press and hold down the buttons again. is an external alarm button connected, you can also activate the alarm mode by pressing it. Messaging Alarm mode is activated automatically when Ping™ 6 is moved outside the defined location Sending and receiving messages while in anchor mode. Position updates, tracking updates, anchor and While in alarm mode, Ping™ 6 is running at other alarms are transmitted as SMS messages full power and is ready to respond into your by Ping™ 6. Sending tracking updates and commands. The mode is automatically left after anchor alarms, functions automatically when one hour, or if another mode is activated by a the desired mode is on, and defined conditions command. -
Page 11: Voice.calling
there are no numbers defined in the White list, White list is not defined, the call is accepted. the phone number is considered as valid, and For more information about defining automatic position update is sent as a reply. For more answer and White list, see Config 9: Voice call information about the White list, see page 19. auto answer on page 14 and White list. Configuration Voice calling Voice calling enables you to listen in on the Installing software and drivers Ping™ 6. When the call starts, the microphone... -
Page 12: Configuration Settings
Once the software is open, choose the right If the PIN code is wrongly defined, you won’t be COM-port from the COM drag-down menu and able to turn on your Ping™ 6. After three failed press Connect. The connection between attempts, the SIM card will be blocked and you Ping™ 6 and PC is established. need PUK code to unblock it. If your SIM card gets blocked, you need PUK Configuration settings code (8 digits) to open it. Remove the SIM Connect Ping™ 6 to your computer as described card for Ping™ 6 and install it into a phone in Connecting to computer. You can edit and compatible with your SIM card. When you’re define several settings, including security trying to open the phone, it will prompt you for settings and available connections, to be used the PUK code. After entering the PUK code, key with you Ping™ 6. in new PIN code. You can then install the SIM card back to Ping™ 6. Security settings If you fail to key in the correct PUK code Ping™ 6’s SIM card can be protected by defining 10 times in a row, your SIM card will be PIN and security code numbers. You can also permanently blocked. If this happens, contact... -
Page 14: Config 2: Id
Config 2: ID Write the phone numbers with international code. You can define an identification code for your Ping™ 6. The code can contain both numbers Voice call settings and letters, and it’s case sensitive. Default value Voice calls can be initiated by Ping™ 6 under for ID is: Ping. specific circumstances. You can define settings Alarm settings for terminating, auto answering voice calls, and allowed numbers for outgoing voice calls. Config 15: Max allowed movement in anchor mode Config 9: Voice call auto answer You can define a max. -
Page 15: White List
Config 28-29: Voice call numbers White L1-5: White list numbers Available phone numbers for outgoing voice You can define up to 5 white list numbers that calls can be defined in configuration fields 28- can be any valid phone numbers. The white list 29. Write the phone number digits together is activated when at least one phone number is without blanks and special characters. If you stored. Incoming voice calls and commands will want to use international phone numbers, write then only be accepted if they are received from sign + in front of the number. Or use national white list numbers. The authorization is done phone numbers without + and country code. by comparing the last 7 digits in the sender’s phone number to the corresponding digits of all When a call is initiated, Ping™ 6 starts calling your stored white list numbers. Write the phone... -
Page 16: Updating Software
Accessories and batteries To open the existing configuration settings for editing and saving, press Select EE button to The following accessories are available for this search for your Ping™ 6 configuration file. Then product: press Read EE to open the settings currently saved in Ping™ 6. If you want to open settings Accessory Type Order code file stored on your computer, press File Read EE. You can now edit the settings as you wish. Mains charger EU CMA-80-230 YO3005 You can configurate your Ping™ 6 according Mains charger UK CMA-80-230 YO3006...