Advertisement
Quick Links
Advertisement
Summary of Contents for Highland WeatherTree
- Page 1 Installation & Activation Guide...
- Page 2 Thank you for choosing the WeatherTree™. My team has worked hard to make sure your new device is accurate, easy to use and packed securely. If you have any issues with your new WeatherTree™ please make sure to call us immediately at 863-844-4263 or email ws@highlandag.com so we can make it right.
- Page 3 Wind Anemometer UV and Solar Radiation Sensor Rain Bucket Wind Vane Temperature and Humidity housed by Solar Panel Solar Radiation Shield Barometric Pressure, LTE Radio, Battery Power Switches, Status LEDs...
-
Page 4: You Will Also Need
SUPPLIES INCLUDED 13 mm x 2 YOU WILL ALSO NEED Drill, 13 mm Drill Socket, 1/8" Drill Bit 4 x 4” Wood Post... - Page 5 ASSEMBLY Select your WeatherTree™ location in an open area free of trees and buildings. TIP: We recommend using a 4 x 4 inch post that is a minimum of 6 feet above the ground. If installing on a building, we recommend that the sensor array is higher than the roof.
- Page 6 ASSEMBLY Install Wind Anemometer onto Sensor Array. Using screwdriver provided, tighten but DO NOT overtighten set screw on side of Wind Anemometer.
- Page 7 ASSEMBLY Mount sensor Array onto mounting pole. Make sure the rain bucket is facing exactly north. Using the wrench provided, tighten the U-bolts. NOTE: The device needs to be as close to north (0) degrees as much as possible for the most accurate readings.
- Page 8 ASSEMBLY Center bubble level and drill the second pilot hole for the bottom bracket bolt. Install and tighten bottom bracket bolt. Tighten adjustment bolts on pole on both sides. 13 mm Mount Solar Panel bracket at least 5" below Wind Vane. Solar Panel must be facing south. Tighten mounting bracket lever.
- Page 9 ASSEMBLY Pull battery tab. RESET Using screwdriver provided, press the RESET button for 5 seconds. Once released, the red light should appear.
- Page 10 ASSEMBLY Press and hold the OFF button for 2 seconds to ensure the unit is off. STAT Press and hold the ON button until the status (STAT) light is blinkng. STAT After you press and hold the ON button to put into diagnostic mode, the STATUS LED will flash for approximately 2 minutes.
- Page 11 If you are a new customer, follow the instructions below. If you are an existing customer, skip to section 9. You will need to create your account before you can set up your Weathertree™. Go to www.highlandhub.com and click Create Account. User Information...
- Page 12 If you do not see the email, check your SPAM or junk mail folder. Once verified, continue setting up the WeatherTree™ by immediately following directions in section 9. NOTE: Do not Log in until you have followed instructions in section 9.
- Page 13 Enable location services for the next step. Scanning the QR Code Locate the QR code on the WeatherTree™. Using a 4G smartphone (Google Android or Apple iOS) use your camera to scan the QR code. If your device does not recognize the QR code, download QR code-reading app and use it to scan the QR code.
-
Page 14: Warranty
WARRANTY 1 Year Limited Warranty We warrant the Weather Tree to be free from defects in material and workmanship for one (1) year from the original date of purchase. We expressly disclaim any implied Warranties of merchantability or fitness for particular purpose. - Page 15 For further details or to request a demonstration, contact Taylor Pippin Cell: 813-731-6244 or tpippin@highlandag.com Highland Ag Solutions is Highland Precision Ag, Highland Fresh Technologies and Coastal Ag Supply 590 NW 3rd Street, Mulberry, FL 33860 USA | 863-844-4263 info@highlandag.com | highlandagsolutions.com Proudly designed and constructed in the USA Learn more at HighlandHasIt.com...
Need help?
Do you have a question about the WeatherTree and is the answer not in the manual?
Questions and answers