Subscribe to Our Youtube Channel
Related Manuals for PESA PRO-8X8-DVI
Summary of Contents for PESA PRO-8X8-DVI
- Page 1 PRO-8X8-DVI 8X8 DVI Router User Manual Made in Taiwan rev.1008 103 Quality Circle, Suite 210 | Huntsville, Alabama 35806 | Tel: (256) 726-9222 | Fax: (256) 726-9268 | Email: service@pesa.com...
-
Page 2: Safety And Notice
PESA Switching Systems, Inc., (PESA) warrants this equipment against defective workmanship or materials for a period of one (1) year from date of shipment. The sole warranty responsibility of PESA, shall be to replace or repair product proved to be defective. During the warranty period, defective parts will be replaced at no charge. - Page 3 INTRODUCTION The PESA PRO-8X8-DVI 8X8 DVI Router provides the most flexible and cost effective solution in the market to route high definition video sources from any of the eight DVI source devices to any eight digital displays at the same time.
-
Page 4: Specifications & Package Contents
Operation temperature 32-104°F / 0-40°C Storage temperature -4-140°F / -20-60°C Relative humidity 20-90% RH (no condensation) 1x PRO-8X8-DVI 1x UL AC C13 power cord 1x IR receiver cable 1x Installation CD Package Contents 1x IR remote control 1x User manual 2x 1RU rack mounting ear USB or RS-232 control must be connected either one at a time. -
Page 5: Panel Description
Front Panel OUTPUT PORT INPUT CHANNEL Ext. IR 8X8 DVI Router PRO-8X8-DVI IR SENSOR 1. Power on/off control switch 2. 3.5mm IR socket for plugging in the external IR receiver 3. LED indicators for output port and input channel mapping display 4. -
Page 6: Dip Switch
Firmware update only can be done via RS-232 port and connection to PC set at COM1 1. Turn off the PRO-8X8-DVI. Execute the firmware update program on your PC via COM1 port connection to the RS-232 port of the PRO-8X8-DVI. - Page 7 IR EXTENDER 3.5mm IR Socket IR Receiver 1=Power 2=IR signal [36-40KHz] 3=Grounding 1 2 3 Ext. IR: Plug the IR receiver here to receive all IR command signals from the IR remote control ~ 5 ~...
-
Page 8: Installation
2. Connect all displays to DVI-D outputs on the PRO-8X8-DVI. 3. Connect the IR receiver to the Ext. IR jack on the front panel of PRO-8X8-DVI and direct the IR receiver to where it can receive IR commands from the IR remote reliably. -
Page 9: Channel Control
CHANNEL CONTROL Method A: Push Button 1. Press the buttons on OUTPUT PORT to select which port to be changed. “ ”: change selected output port in ascending order “─“: change selected output port in descending order 2. Press the buttons on INPUT CHANNEL. The source will be sequentially changed. After few seconds, the setting will be active. - Page 10 Method C: Software Control through RS-232 or USB Software Control Panel 1. Setting Click on Get to read back device ID. Click on Set to write device ID. Click on Rename to open the String Table. In the String Table, assign the captions for each input and output port for easy recognition. For example: Rename the Input1 to “Desktop PC1”, Input2 to “Laptop2,”...
- Page 11 Click on Save String Table to save the caption setting (turn effective after program restart) Click on Set Default to pop up the confirmation message below to erase the captions and reset the string table back to default setting. (turn effective after program restart) 2.
- Page 12 3. Linkage: Click on Linkage to read back all status. 4. Open/Close: Click on Open or Close to close or open COM port. 5. Mapping Select All Output Click on Select All Output”, and then select the source on main menu. You can quickly set all output to the same source.
- Page 13 7. Output Port: Pull down menu and select which source to be sent to this output port. One by one setting On main menu screen. First select input source. Then select the output ports which you want to send the video and audio from this source. When you select the input source, the source will change to gray.
- Page 14 Command Set: COMMAND ACTION COMMAND ACTION System Status Firmware Version Output A selects Input 1 Output E selects Input 1 Output A selects Input 2 Output E selects Input 2 Output A selects Input 3 Output E selects Input 3 Output A selects Input 4 Output E selects Input 4 Output A selects Input 5...
-
Page 15: Edid Learning
EDID LEARNING The PRO-8X8-DVI has a built-in EDID profiles designed to cover most of the widely used resolutions for the ease of installation. Default EDID Native/preferred timing: 1680 x 1050p at 60Hz (16:9) Detailed timing #1: 1920 x 1200p at 60Hz (16:9) - Page 16 IR DISCRETE CODES Default Custom Code — IR2 Code: 00 FF — Function POWER 0x17 0x02 0x0A 0x0C SOURCE SEL. 1 SOURCE SEL. 2 SOURCE SEL 3 SOURCE SEL. 4 0x54 0x55 0x56 0x01 SOURCE SEL. 5 SOURCE SEL. 6 SOURCE SEL.
- Page 17 Custom Code — IR4 Code: 0x13 0x31 Custom Code: 0x13 0x31 Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 0xAE 0xBE 0xCE 0xDE 0xEE 0xFE 0x1E 0x2E Source 1 0xAD 0xBD 0xCD 0xDD 0xED 0xFD...
- Page 18 NOTICE USB or RS-232 control must be connected either one at a time. Connecting both types of cables may cause command confusion. ~ 16 ~...
-
Page 19: Troubleshooting
TROUBLESHOOTING 1. Why the buttons on the front panel and remote control are all out of control? It might be because of a function called System Lock which can prevent unnecessary misusage after installation. Please refer to the CHANNEL CONTROL section to know how to unlock. 2. - Page 20 PRO-8X8-DVI 8X8 DVI Router PESA Switching Systems, Inc. 103 Quality Circle, Suite 210 Huntsville, Alabama 35806 Tel: +1 (256) 726-9222 Fax: +1 (256) 726-9268 Email: service@pesa.com...
Need help?
Do you have a question about the PRO-8X8-DVI and is the answer not in the manual?
Questions and answers