Related Manuals for Magicfx STADIUMBLASTER MFX0803
Summary of Contents for Magicfx STADIUMBLASTER MFX0803
- Page 1 USER AND INSTALLATION MANUAL ENGLISH STADIUM BLASTER. ® PART01104 CONFETTI & STREAMER FX rev 01-01...
-
Page 2: Disclaimer
Failure to read the manual and to follow the printed instructions may lead to personal injury and/or damage to the product. © 2019 MAGICFX ® All rights reserved. Nothing from this publication may be copied, reproduced and/or published by means of printing, photocopying or by any other means, without the prior written approval of MAGIC FX. -
Page 3: Table Of Contents
TABLE OF CONTENTS Disclaimer Trademarks Liability Foreword Language Revision table Meet the MAGICFX STADIUMBLASTER! ® Main parts Technical data 1.3 Product identification 1.4 Accessories 1.5 Confetti DMX control 1.7 Display panel 1.8 RDM capability Blast safely! 2.1 General safety rules Indoor use Rigging Noise level 2.6 Safety symbols 2.7... -
Page 4: Foreword
This document contains the original instructions in English. In case you require other languages please contact MAGIC FX. REVISION TABLE Doc nr Revision Date Description Author Approved PART01104 01-00 13-2-2017 Initial release PART01104 01-01 1-8-2019 A4 to A5 format MAGICFX STADIUMBLASTER — User and Installation Manual ®... -
Page 5: Meet The Magicfx ® Stadiumblaster
MEET THE MAGICFX STADIUMBLASTER! ® The MAGICFX STADIUMBLASTER is a special effects machine that launches confetti ® into the air up to a height of 12 metres. The MAGICFX STADIUMBLASTER is equipped with a CO powered woofer. CO is blown ®... -
Page 6: Technical Data
TECHNICAL DATA Product Product Name MAGICFX STADIUMBLASTER ® Product Code MFX0803 Product Type CONFETTI & STREAMER FX Main Length 800 mm 31.5 in Dimensions Width 600 mm 23.6 in Height 1100 mm 43.3 in Weight Weight 84.3 kg 185.8 lb Environment Minimum Temperature -20 °C... -
Page 7: Product Identification
TRUE1 - cable 1.5 m ® Accessories CONFETTI The MAGICFX STADIUMBLASTER can be set in 5 different angles between 45° and 90°. ® The output height and output distance depends on the type of confetti and the set angle. The maximum load per blast also depends on the type of confetti. Check the following table. -
Page 8: Dmx Control
DMX CONTROL When connected to DMX the MAGICFX STADIUMBLASTER is controlled with 1 safety ® address and 1 operational address: DMX Address Address range Safety 1 – 512 Start 1 – 512 DMX addresses The safety address cannot be the same as (one of) the operational address(es). - Page 9 The display panel is located on the backside of the MAGICFX STADIUMBLASTER. ® Check the following menu structure for all options in the menu. Use the buttons for navigation and selection. The left-hand LED blinks red when DMX is active. The right- hand LED continuously lights red when an error is present.
-
Page 10: Rdm Capability
RDM can be used for configuration and status monitoring while DMX512 takes care of the default controlling. For RDM you will need a RDM compatible controller. The following RDM parameters STADIUMBLASTER. are supported by the MAGICFX ® Parameter ID Discovery... -
Page 11: Blast Safely
Are free of dust, corrosive gases and high concentrations of organic vapours. • Are not situated in the vicinity of a source of vibration. GENERAL SAFETY RULES • Only authorised persons may carry out work with the MAGICFX ® STADIUMBLASTER. • Do not use the MAGICFX STADIUMBLASTER if there are people or animals in ®... -
Page 12: Indoor Use
• Installing CO monitoring devices that will warn for hazardous CO levels. Do not use the MAGICFX STADIUMBLASTER in poorly ventilated ® DANGER confined spaces. Exposure to high levels of CO gas can cause symptoms like headache, nausea, loss of consciousness or even death. -
Page 13: Safety Symbols
Make sure there are no objects near the output that can be WARNING damaged or overthrown by the MAGICFX STADIUMBLASTER. ® Always create a safety zone around the MAGICFX ® WARNING STADIUMBLASTER and its output according to the following picture. MAGICFX STADIUMBLASTER —... -
Page 14: Let's Blast
LET’S BLAST! INSTALL THE MACHINE Bring the cased MAGICFX STADIUMBLASTER to the desired location. ® Unlock and remove the top cover. MAGICFX STADIUMBLASTER — User and Installation Manual ®... - Page 15 Unlock and remove the cover from the bottom cabinet. Take out the woofer. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 16 Screw the woofer firmly onto the bayonet socket of the hopper until it locks in place. Secure the woofer with the safety steel. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 17 Optionally you can set the hopper with the attached woofer in one of the 5 pre-set angles. Place the MAGICFX STADIUMBLASTER in its final position and set the brakes. ® Take the necessary safety precautions, see Section 2.7. MAGICFX STADIUMBLASTER — User and Installation Manual 17...
- Page 18 Make sure the manual CO valve is in CLOSED position. Connect the CO hose to the CO quick connector. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 19 Connect the CO hose to the CO₂ Bottle to Hose Connector on the CO cylinder. Open the CO cylinder. In case of multiple machines: Repeat steps 1 – 14 for each machine. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
-
Page 20: Fill With Confetti Before Each Blast
FILL WITH CONFETTI BEFORE EACH BLAST Unlock and open the lid of the hopper. Fill the hopper with confetti. Check Section 1.5 for the maximum amount per type of confetti. 20 MAGICFX STADIUMBLASTER — User and Installation Manual ®... -
Page 21: Blast Manually
The best effect results are achieved when you open the lid just NOTICE before you start blasting. Make sure that no foreign objects will enter the hopper and close the lid again after the effect. MAGICFX STADIUMBLASTER — User and Installation Manual ®... - Page 22 Enjoy the view! When the hopper is out of confetti, move the manual CO valve back in CLOSED position. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
-
Page 23: Connect 24 V Control
1. Connect two cables to the 24 V input. 2. Connect the other ends of the cables to your controller. No additional power source is needed. The controller provides NOTICE power to the MAGICFX STADIUMBLASTER to open and close the ® output valve. -
Page 24: Connect Power And Setup Dmx
5. Use the display and buttons or a RDM controller to assign DMX addresses, see chapter 1. Always plug in a DMX Terminator into the DMX output. Using a CAUTION DMX Terminator improves signal reliability. MAGICFX STADIUMBLASTER — User and Installation Manual ®... -
Page 25: Setup Multiple Machines In A Sequence With Dmx
Make sure that no foreign objects will enter the hopper and close the lid again after the effect. 4. Enjoy the view! 5. Deactivate the Start address when the hopper is out of confetti. MAGICFX STADIUMBLASTER — User and Installation Manual ®... -
Page 26: Replace A Co Cylinder
Close the CO cylinder. Move the manual CO valve in OPEN position to release the pressure from the system. Move the manual CO valve back in CLOSED position. MAGICFX STADIUMBLASTER — User and Installation Manual ®... - Page 27 Bottle to Hose Connector on the CO cylinder. Remove the CO Bottle to Hose Connector from the cylinder. Connect a CO Bottle to Hose Connector to a new CO cylinder. MAGICFX STADIUMBLASTER — User and Installation Manual 27 ®...
-
Page 28: Clean Up
In case of multiple machines: Repeat steps 1 – 9 for each machine. 3.10 CLEAN UP Deactivate the Safety address (FX LED indicator on each machine dims). Disconnect any 24 V, DMX and power cable(s). Close the CO cylinder. MAGICFX STADIUMBLASTER — User and Installation Manual ®... - Page 29 OPEN position to release the pressure from the system. Disconnect the CO hose from the CO quick connector. Disconnect the CO hose from the Bottle to Hose Connector on the CO cylinder. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 30 Connector from the cylinder. Wait until the ice crust on the output has melted. In case you have set the hopper under an angle: Position the hopper back in horizontal position (position 1). 30 MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 31 Remove the safety steel. Remove the woofer. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 32 Remove the woofer. Place and lock the cover of the bottom cabinet. Unlock and open the lid from the hopper. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
- Page 33 Remove remaining confetti from the hopper. Close and lock the lid from the hopper. Place and lock the top cover. Release the brakes. MAGICFX STADIUMBLASTER — User and Installation Manual ®...
-
Page 34: Maintenance
MAINTENANCE To achieve the maximum service life of the MAGICFX STADIUMBLASTER you must ® regularly clean the MAGICFX STADIUMBLASTER and test if it is functioning correctly. ® Contact MAGIC FX if the MAGICFX STADIUMBLASTER is not functioning correctly. ® Do not replace parts yourself; always consult MAGIC FX. -
Page 35: Ec Declaration Of Conformity
Translation of the original declaration of conformity Name manufacturer : MAGIC FX BV Address : Schouwrooij 27, 5281 RE BOXTEL Country : The Netherlands : B. Veroude Date : 17-01-2017 Signature MAGICFX STADIUMBLASTER — User and Installation Manual ®... - Page 36 WWW.MAGICFX.EU...
Need help?
Do you have a question about the STADIUMBLASTER MFX0803 and is the answer not in the manual?
Questions and answers