Upgrading Firmware
Upgrade SR130 firmware through the Paradox In-Field software (V3.0 or higher) using the 307 USB Direct
Connect Interface. The SR130 requires the batteries installed in order to upgrade the firmware.
Note: Ensure that the SR130 is awake before beginning the firmware upgrade. To wake-up the siren,
press the training/reset switch (see connector #4 in Figure 1). The siren provide yous a 60 second
delay in order to begin the update.
1.
Remove the front cover (see Figure 2).
2.
Connect the 307 USB to the In-Field connector (see connector #8 in Figure 1).
3.
Upgrade according to the firmware upgrade instructions: Go to www.paradox.com >Software >
In-Field Firmware Upgrade Instructions.
Tamper Supervision
If a tamper is detected, the SR130 sounds an alarm and the strobe light flashes for 4 minutes. The control
panel follows the global supervision options set in the panel.
Specifications
Specification
Power Supply
3x 1.5VDC "C" alkaline batteries.
Battery life
Up to 3 years based on normal use (e.g. 2 alarms per year with strobe for
2.5 hours and 8 squawks per day at an average of 25ºC (77ºF) with default
alarm time set to 4 minutes. If the alarm is set for more than 4 minutes,
the battery life may be reduced).
Battery Low Voltage
Signal sent at 4.1 VDC
Signal
RF frequency
433MHz or 868MHz
RF range
Up to 70m (230 ft)
Siren
100dBA or more (1 meter)
Humidity Range
5% to 90%
Dimensions
13.43cm X 21.17cm X 5.1cm (5.29in X 8.34in X 2.01in)
Weight
365g /12.87oz., 567g/20 oz. with batteries
Certifications
CE EN 50131-4 Grade 2
EN 50130-5 Class IV
Warranty
For complete warranty information on this product, please refer to the Limited Warranty Statement found on the
Statement. Your use of the Paradox product signifies your acceptance of all warranty terms and conditions. Please
ensure that your use of the Paradox product is in compliance with local, national, and international laws.
© 2015 Paradox Security Systems (Bahamas) Ltd. All rights reserved. Specifications may change without prior notice.
US, Canadian and international patents may apply. BabyWare and Paradox are a trademarks or registered
trademarks of Paradox Security Systems (Bahamas) Ltd. or its affiliates in Canada, the United States and/or other
countries.
Description
SR130 Outdoor Wireless Siren w/Built-In Strobe Light
SR130-EI01 Version 1.1
Printed in Canada 04/2015
Overview
The SR130 is a stand-alone, fully supervised outdoor wireless siren with built-in strobe light and wireless
transceiver. The SR130 uses 2-way wireless communication, which provides continuous supervision
between the panel and siren with fast response to alarm signals within four seconds With normal use, the
SR130 will function up to three years without the need to replace the batteries. The SR130 operates using
three 1.5VDC size "C" alkaline batteries.
This guide describes how to install and configure the SR130 wireless siren.
SR130 I/Os and Connectors
1
2
3
4
5
6
7
Figure 1: SR130 I/Os and Connectors
1.
Siren (100dB or more)
2.
Tamper Spacer
11
3.
Wall Tamper switch and Cover Tamper
switch
4.
Reset/Training switch
10
5.
Tamper Switch connector
6.
Battery pack (3 size "C" alkaline batteries)
9
7.
Strobe lights
8.
In-Field connector
8
9.
Signal Strength and transmission LED
10. Antenna
11. LED Status Indicator
Need help?
Do you have a question about the SR130 and is the answer not in the manual?
Questions and answers