Emptying The Waste Bin; Cleaning And Servicing The Filter; Replacing Light Bulbs - Genius 1300 DP Use And Maintenance Handbook

EMPTYING THE WASTE BIN

This machine can be fitted with visual and acoustic devices
signalling when the waste bin is full – see letter 'Q' of Fig. 3.
When the 'waste bin full' indicator light comes on, at the same
time the code CPUU will start flashing on the display. Empty the
bin.
To empty the waste bin, press and hold down the consent button
located on the left of the instrument board and select the
requested function.
1- Press the button on the console - letter 'I' of Fig. 3 - and hold
it down until the requested emptying height has been reached.
2- Move to the waste container.
3- Press the button on the console - letter 'M' of Fig. 3 - and hold
it down until the bin has been tipped to enable all its contents to
fall out. As soon as you release this button, the bin will
automatically return to its horizontal position.
N.B.: the machine features a safety device that prevents the bin
from rotating unless it has reached a safe distance from the
machine. In fact, no damage will be caused if the operator
presses button M by mistake, i.e. before the bin has reached its
pre-established height.
4- Move away from the waste container and press the butto,
which is marked 'L' on Fig. 3, so that the bin can gain its initial
position (lowered).

CLEANING AND SERVICING THE FILTER

The filter is a very important component of the machine and
essential for correct operation.
Proper filter maintenance will allow you to obtain the best
performance from your machine.
The filter can be cleaned in any of the following three ways:
1) by means of the automatic cleaning system
As you select a work programme, the machine will automatically
adopt an automatic cleaning cycle for the two filter shakers and
the filter, which is based on a pre-established series of time
English
settings.
2) by means of an electric filter shaker that is manually started
Just a simple command is needed to keep the filter in perfect
working order: press the button marked 'F' on Fig. 3 and hold it
down for a few seconds. Repeat this operation 4 or 5 times.
Remember that the cleaner the filter, the better the results of
your cleaning session. It is recommended to carry this operation
out at the end of each work cycle.
NOTE: dusty environments
If you are using the machine in a dusty environment (e.g. sawmills
– warehouses where haulage vehicles pass, etc.), it is a good
idea to use the filter shaker more frequently.
3) by manually cleaning the filter
If operating the filter shaker is not enough to keep the filter clean
- and in any case every 20 hours of work - clean the filter
manually. Before carrying out any kind of intervention on the
machine, make sure it is turned off and that all functions are
deactivated. To obtain this condition, turn the switch marked 'O'
on Fig. 3 to OFF.
1° Remove the rear machine panel
2° Take the two filters out of their seat by turning the 4 retainer
handles.
3° Blow compressed air onto the side of the filter featuring the
protective net (at a pressure of 6 bar at the most).
4° Refit the filters and the rear panel.
FITTING AND REPLACING THE SIDE BRUSHES
To facilitate transport, the side brush (or brushes) is not fitted in
its expected working position.
To fit the brush in its correct working position, proceed as follows:
1- Pull up the brush knob.
2- Loosen the screw on the shaft of the side brush motor.
3- Remove the key protection.
4- Place the brush with its flange on the shaft.
5- Tighten the fixing screw.
To replace worn side brushes, carry out the operations listed
above.
Important : raise and lower the side brushes while the
machine is running.

REPLACING LIGHT BULBS

To replace the front light bulb:
Remove the front cover by loosening the fixing screws.
Replace the bulb, making sure that the new bulb has suitable
electrical features.
Refit the front cover.
- 21 -