Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Enerdrive Manuals
  4. Power Pack
  5. Lithium Power Pack Series
  6. Owner's manual

Enerdrive Lithium Power Pack Series Owner's Manual

Lithium-ion battery system with epro plus battery monitor
Hide thumbs

Advertisement

Quick Links

Download this manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the Lithium Power Pack Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Enerdrive Lithium Power Pack Series

  • Page 2 After 2 years of research, testing and proving, and a further 6+ years of infield sales, Enerdrive has designed and created a COMPLETE Lithium Battery & Installation System so your Li-Ion battery bank is fully protected. Most importantly, our system is designed to give the maximum performance, longevity and SAFETY in your valuable installations.
  • Page 3 The Enerdrive Advanced BMS Relay Driver will turn the main battery relay OFF every 6 minutes if the SOC% on the battery monitor is still below the set point. So this may need to be reset a few times before the SOC% set point reaches its re-engagement point.

  • Page 4: Status Led

    4 x “TOR” Circuits – Programmed to control Enerdrive ePOWER AC & DC2DC Chargers, & Morningstar Solar Controllers (Hi/Low Alarm Protection). 4 x Normally Open/Closed/Common Contacts (10 Amps Max) – programmed to switch trigger contacts/relays connected to Alternators*, Chargers, Solar or DC/AC relays, cabinet cooling fan and Combi Inverter/Charger Units.
  • Page 5 When Red LEDs are on, all output circuits are disabling When Red connected charge sources. Status LED OUTPUT 4 ePRO Combi When Red LEDs are off, Cabinet Cooling Inverter Flashing GREEN - LOW SOC% <24% or LOW CELL Voltage all output circuits are within shutdown Fan Control <2.8/Cell (Load Shutdown)
  • Page 6 What’s in the Enerdrive Lithium System? To use the Enerdrive Lithium Power Pack you need to use a combination of items together. These are: • The actual lithium power pack battery box including Active Balancing System. • The Advance BMS controller board which includes •...
  • Page 7 Voltages for Lithium batteries have a very narrow window compared to lead acid batteries. With all of our testing over the last 6+ years, the Enerdrive Lithium battery standing voltage when fully charged (with no loads running) will be between 13.35v-13.45v at 100% capacity.

  • Page 8: Important Please Read

    Enerdrive lithium battery in a charged state. Your lithium battery should not be left for more than 30 days without checking its charge state. Enerdrive recommend that your lithium battery should ideally be checked and charged as often as possible to maintain maximum life expectancy, especially if you leave any DC loads running.
  • Page 9 Page 9...
  • Page 10 Power Input 1 Input 2 Input 3 Input 4 (if connected) Latching Relay Page 10...
  • Page 11 Troubleshooting the Lithium Battery System Q: What if the battery monitor reads 24% or less or the battery voltage has reached 12.4v or less, and the power has gone out? A: The battery has reached its maximum discharge and the main battery relay has dis-engaged to protect the battery.
  • Page 12 YELLOW GREEN BLACK BLUE WHITE...
  • Page 13 YELLOW GREEN BLACK BLUE WHITE YELLOW GREEN BLACK BLUE WHITE...
  • Page 14 YELLOW GREEN BLACK BLUE WHITE...
  • Page 15 YELLOW GREEN BLACK BLUE WHITE...
  • Page 16 YELLOW GREEN BLACK BLUE WHITE YELLOW GREEN BLACK BLUE WHITE...
  • Page 17 YELLOW GREEN BLACK BLUE WHITE YELLOW GREEN BLACK BLUE WHITE...
  • Page 18 Pro-Rata warranty applicable to original end user only. Enerdrive does not warrant the battery for use in any residential system sold with the intent or purpose The Enerdrive ePRO Plus battery monitor that is standard with every Lithium-Ion battery kit is pre- The warranty does not cover a battery reaching its normal end of life which may occur prior to the warranty period stated above.
  • Page 19 It is the responsibility of the end user to maintain the battery in a charged state. The battery should not be left for more than 30 days without checking its charge state. Enerdrive recommend that a battery left in a “storage state” should be checked and charged every 30 days to maintain maximum life expectancy of the battery.
  • Page 20 30 days of original purchase. Any defective unit that is returned to Enerdrive within 30 days of the date of purchase will be replaced free of charge. If such a unit is returned more than 30 days but less than two years from the purchase date, Enerdrive will repair the unit or, at its option, replace it, free of charge.
  • Page 21 Latching relay is in the OFF Position (Yellow button flush with the top of the switch). 2. Make sure the Dip Switch on the right hand side of the Enerdrive ADV-BMS Relay Driver is set to Program A. 3. Leave the main battery cables disconnected until complete.
  • Page 22 Do all charging sources return to normal operation status? Switch on the AC Mains charging source and fully charge the battery until the battery monitor reads 100% to synchronise the Battery Monitor. Ensure all Enerdrive ePOWER (if installed) & DC2DC chargers are set to “Lithium” and programmed accordingly If you have answered YES to all questions, congratulations , your Lithium System is ready for use! Customer/End User Name if known.
  • Page 23 If there are no Red LEDs turned on - call Enerdrive. A: Check that the EN3TOR-G2 sensor lead is connected to the Temp Port on the Enerdrive AC Charger and connected to one of the TOR Ports on the Advanced Relay Driver.
  • Page 24 NOTES: Page 25...
  • Page 25 ENERDRIVE PTY LTD P.O. Box 9159, Wynnum Plaza, Queensland, Australia 4178 Ph: 1300 851 535 / Fax: 07 3390 6911 Email: support@enerdrive.com.au Web: www.enerdrive.com.au...