Summary of Contents for CalAmp LMU-30 Series
- Page 1 LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide CalAmp Corp. 13645 Dulles Technology Drive, Herndon, VA 20171 Document: MBUD-0268v1.4 Phone: 703. 262.0500 June 2016 Fax: 703.262.0380 www.calamp.com...
- Page 2 All trademarks used are properties of their respective owners. Products offered may contain software proprietary to CalAmp or other parties. The offer of supply of these products and services does not include or infer any transfer of ownership. No part of the documentation or information supplied may be divulged to any third party without the express written consent of CalAmp.
-
Page 3: Table Of Contents
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide TABLE OF CONTENTS REGULATORY INFORMATION ..................1 ..................1 UMAN XPOSURE OMPLIANCE TATEMENT ........................1 ARDWARE RECAUTIONS INTRODUCTION ....................... 2 LMU-30XX/CVF-3030 & OBD-II EXTENDER CABLE OVERVIEW ........... 3 LMU-30 /CVF-3030 E ............... - Page 4 CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide LIST OF FIGURES Figure 1: LMU-30xx/CVF-3030 ........................3 Figure 2: OBD-II Extender Cable - (6ft, P/N 144301 or 2ft, P/N144302) ............3 Figure 3: Tamper Tape Applied and Removed ....................3 Figure 4: Remove Bottom Panel ........................
-
Page 5: Regulatory Information
§ 1.1307(b), § 2.1091 and § 2.1093, as appropriate. CalAmp certifies that it has determined that the LMU-30xx/CVF-3030 complies with the RF hazard requirements applicable to broadband PCS equipment operating under the authority of 47 CFR Part 24, Subpart E of the FCC Rules and Regulations. -
Page 6: Introduction
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 2 INTRODUCTION This guide provides on-site service information for the basic setup and installation of the LMU-30xx/CVF- 3030 device and OBD-II Extender Cable. It is important to perform all installation steps in the order identified in this guide to minimize any potential damage to the vehicle or equipment. -
Page 7: Lmu-30Xx/Cvf-3030 & Obd-Ii Extender Cable Overview
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 3 LMU-30XX/CVF-3030 & OBD-II EXTENDER CABLE OVERVIEW The LMU-30xx/CVF-3030 features a small size, superior GPS design, OBD-II interface, and a 3-axis accelerometer. These features enable the LMU-30xx/CVF-3030 to access vehicle diagnostic interface data, track vehicle speed and location, and operational information. -
Page 8: Lmu-30
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 3.1 LMU-30xx/CVF-3030 Environmental Specifications The LMU-30xx/CVF-3030 device is designed to operate in the following specified environments. General Specifications Communication modes: cellular and SMS Location technology: 50 channel GPS ... -
Page 9: Obd-Ii Extender Cable Specifications
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide OBD-II Extender Cable Specifications The OBD-II Extender Cable is designed with the following specifications. General Specifications RoHS Compliant All 16 pin connected Right-angle design allows for easy use and concealment ... -
Page 10: Tools And Materials
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 3.3 Tools and Materials The following materials are required for proper installation of the LMU-30xx/CVF-3030 and OBD-II Extender Cable. No additional tools are required. LMU-30xx/CVF-3030 Device OBD-II Extender Cable 6ft – P/N 144301 2ft –... -
Page 11: Installation
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 4 INSTALLATION For a protected installation, the LMU-30xx/CVF-3030 device is typically installed under the vehicle dashboard on the driver side, however, another common installation location include behind the A-pillar panel on the driver side of the vehicle. This section outlines the steps in sequential order for installing the components in a typical installation. -
Page 12: Dissemble Vehicle Panel
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 4.1 Dissemble Vehicle Panel The first step of the installation requires removing the panels on the driver’s side of the vehicle. The panel you remove depends on the selected install location. The following instructions show the typical under the dashboard panel removal. -
Page 13: Figure 6: Remove Top Panel
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 3. Remove the panel behind and next to the steering column. Figure 6: Remove Top Panel Place your hand on the panel, and then gently pull the panel outward until the left-side of the panel snaps out. -
Page 14: Cvf-3030 Device
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 4.2 Connect the OBD-II Extender Cable and LMU-30xx/CVF-3030 Device After you have successfully removed the panels, connect the OBD-II Extender Cable and LMU-30xx/CVF- 3030 device. To Connect the OBD-II Extender ion Cable and LMU-30xx/CVF-3030 Device: 1. -
Page 15: Figure 9: Tamper Tape Over Lmu-30Xx/Cvf-3030 And Obd-Ii Extender Cable Connection
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide Figure 9: Tamper Tape over LMU-30xx/CVF-3030 and OBD-II Extender Cable Connection 4. To deter potential device tampering, apply a piece of tamper tape over the connection. When the tamper tape is removed, the tape self-destructs to indicate removal and leaves behind a residue on the device. -
Page 16: Figure 11: Secure The Extra Obd-Ii Extender Cable
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide The orange light takes approximately 45 seconds to go from a blinking state to a solid state. A solid orange light indicates a cellular connection. The green light takes approximately 15-45 seconds to go from a blinking state to a solid state. A solid green light indicates the device established a GPS connection. -
Page 17: Reassemble The Vehicle Panel
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide The LMU-30xx should be placed non-label side up and not obstructed by metal. The CVF-3030 should be place with the Air ID label side up and not obstructed by metal. - Page 18 CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 4. To deter potential device tampering, apply a piece of tamper tape over the OBD-II port connection (not shown). When the tamper tape is removed, the tape self-destructs to indicate removal and leaves behind a residue on the device.
-
Page 19: Fo Mobileinstall App
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 5 FO MOBILEINSTALL APP After completing the physical device installation, use the FO MobileInstall app to test device communication and create a device-to-vehicle assignment in FleetOutlook. Using your smartphone or tablet, scan the Device ID (ESN) and vehicle VIN. The FO MobileInstall app will create the device-to- vehicle assignment in FleetOutlook. -
Page 20: Verify Device Communication
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 6 LO MOBILE INSTALL APP After completing the physical device installation, use the LO MobileInstall app to test device communication and create a device-to-vehicle assignment in LenderOutlook. Tap the MobileInstall icon on your phone or tablet’s screen. The MobileInstall Login screen displays. -
Page 21: Figure 17: Enter Vehicle Details
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide Enter Vehicle Details 1. Tap in the Asset Name field, and then enter the vehicle name. * This name is used to identify the vehicle throughout LenderOutlook. 2. Tap in the Description field, and enter a short vehicle description. -
Page 22: Figure 18: Test Install
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide locate the vehicle, you use one action. If your device includes the Enable Starter and/or Payment Reminder options, follow the testing steps below. 1. Tap the Disable Starter button. MobileInstall sends the disable starter command to the device. -
Page 23: Figure 19: Apply Geozones
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide Figure 19: Apply Geozones 7 VERIFY DEVICE COMMUNICATION After successful device installation in a vehicle, verify device communication using the Breadcrumb Detail module in FleetOutlook. This is a two-step process and requires a user to be signed in FleetOutlook. -
Page 24: Diagnostic And Vehicle Maintenance
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 8 DIAGNOSTIC AND VEHICLE MAINTENANCE Prior to performing vehicle maintenance, disconnect the OBD-II Extender Cable from the vehicle’s OBD-II Port. Once the OBD-II Extender Cable is removed, access to the vehicle bus data is available. -
Page 25: Warranty
(i) hardware normally consumed in operation such as fuses, cables, or mounting brackets, (ii) defects which, due to no fault of CalAmp Corp, are the result of improper use or maintenance of the Equipment, (iii) improper operation of the Equipment used with other equipment,... -
Page 26: Customer Support Contact Information
CalAmp | LMU-30xx/CVF-3030 & OBD-II Extender Cable Install Guide 10 CUSTOMER SUPPORT CONTACT INFORMATION CalAmp’s Customer Support team stands beside you to ensure any concerns you have with any element of your solution – application, hardware or operations – are addressed quickly and completely.
Need help?
Do you have a question about the LMU-30 Series and is the answer not in the manual?
Questions and answers