Table of Contents
Advertisement
Quick Links
ELECTRIC TRIM CONTROL INSTALLATION INSTRUCTIONS
CORBIN 955 AND YALE 626F HEAVY DUTY TRIM
FUNCTION DESCRIPTION
1560 – FAIL SAFE
LEVER IS LOCKED WHEN POWER IS ON (CLUTCH IS FREE WHEELING)
WHEN POWER IS REMOVED ALLOWS ENTRY BY LEVER HANDLE.
EXIT DEVICE ALWAYS ALLOWS FREE EGRESS.
MECHANICAL KEY OVERRIDE ALLOWS SOLENOID CONTROL TO BE MOMENTARILY OVERRIDED
SO THAT LEVER ENGAGES CLUTCH AND CAN BE TURNED TO ALLOW ENTRANCE.
TURN KEY 90 DEGREES CLOCKWISE AND HOLD, NEXT TURN LEVER TO RETRACT DEVICE LATCH
AND ENTER. NOTE KEY MUST BE RETURNED TO ORIGINAL POSITION TO BE REMOVED.
1570 – FAIL SECURE
LEVER IS LOCKED WHEN POWER IS OFF (CLUTCH IS FREE WHEELING)
WHEN POWER IS APPLIED ALLOWS ENTRY BY LEVER HANDLE.
EXIT DEVICE ALWAYS ALLOWS FREE EGRESS.
MECHANICAL KEY OVERRIDE ALLOWS SOLENOID CONTROL TO BE MOMENTARILY OVERRIDED
SO THAT LEVER ENGAGES CLUTCH AND CAN BE TURNED TO ALLOW ENTRANCE.
TURN KEY 90 DEGREES CLOCKWISE AND HOLD, NEXT TURN LEVER TO RETRACT DEVICE LATCH
AND ENTER. NOTE KEY MUST BE RETURNED TO ORIGINAL POSITION TO BE REMOVED.
ELECTRIC TRIM SOLENOID CONTROL RATING
MODELS: 1560 – FAIL SAFE CONTROL (POWER LOCK)
1570 – FAIL SECURE CONTROL (POWER UNLOCK)
.33 AMP @ 24 VOLTS AC OR DC ± 2 VOLT (CONTINUOUS DUTY)
MONITORING CONTACT RATING
4 AMP @ 250VAC
WIRING DIAGRAMS
OPTIONAL CONNECTOR
IS AVAILABLE WITH A 4 FT.
DEVICE CABLE
MODEL 1560 AND 1570
Rev. 11/2017
II-E1500-08
Advertisement
Table of Contents
Summary of Contents for Architectural Control Systems 1560
- Page 1 AND ENTER. NOTE KEY MUST BE RETURNED TO ORIGINAL POSITION TO BE REMOVED. ELECTRIC TRIM SOLENOID CONTROL RATING MODELS: 1560 – FAIL SAFE CONTROL (POWER LOCK) 1570 – FAIL SECURE CONTROL (POWER UNLOCK) .33 AMP @ 24 VOLTS AC OR DC ± 2 VOLT (CONTINUOUS DUTY)
- Page 2 INSTALLATION INSTRUCTIONS 1560 AND 1570 ELECTRIC TRIM CONTROL YALE AND CORBIN/RUSSWIN HEAVY DUTY TRIM OPTIONAL CONNECTOR SHOWN RIM CYLINDER INSTALLATION STANDARD RIM CYLINDER SUPPLIED BY OTHERS INSERT RIM CYLINDER THROUGH TRIM ESCUTCHEON AND CYLINDER HOUSING ASSEMBLY. CYLINDER TAILPIECE INSERTS THROUGH CAM SLOT.
- Page 3 Rev. 11/2017 II-E1500-08...
- Page 4 Rev. 11/2017 II-E1500-08...
- Page 5 REMOVE ALL SHARP EDGES AND BURRS FROM END OF TAILPIECE AFTER CUTTING. NOTE: FOR 1560 (FAIL SAFE) DEVICES TAILPIECE IS IN UNLOCKED POSITION WHEN NO POWER IS APPLIED. AND FOR 1570 (FAIL SECURE) DEVICES POWER MUST BE APPLIED TO DEVICE TO POSITION TAILPIECE IN UNLOCKED POSITION PRIOR TO CUTTING.
- Page 6 CABLE ASSEMBLY WIRING REMOVE END COVER AND BOTTOM COVER FROM DEVICE SEE FIGURE 3. PLACE WIRE HARNESS ON THE CARRIER WITH THE CONNECTOR AT THE HEAD OF THE DEVICE. ALLOW 6” FOR CONNECTION TO TRIM CONTROL CONNECTOR, WHICH HAS BEEN PULLED THROUGH ACESS HOLE IN DOOR.
Need help?
Do you have a question about the 1560 and is the answer not in the manual?
Questions and answers