Advertisement
Quick Links
Some dust created by power sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to cause cancer, birth defects
or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement
and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those
dust masks that are specially designed to filter out microscopic particles.
8" ANGLE
POLISHER
®
AlwAYS reAd
inSTrucTionS
before uSing
power ToolS
AlwAYS weAr
SAfeTY goggleS
weAr heAring
proTecTion
Avoid
prolonged
expoSure To
vibrATion
6-715
Advertisement
Related Manuals for Napa 6-715
Summary of Contents for Napa 6-715
- Page 1 To reduce your exposure to these chemicals: work in a well prolonged ventilated area, and work with approved safety equipment, such as those expoSure To dust masks that are specially designed to filter out microscopic particles. vibrATion 8" ANGLE 6-715 POLISHER...
- Page 2 • Do not lubricate tools with flammable or Always check for damaged, frayed volatile liquids such as kerosene, diesel or or loose hoses and fittings, and jet fuel. replace immediately. Do not use • Do not force tool beyond its rated quick detach couplings at tool. See capacity. instructions for correct set-up. • Do not remove any labels. Replace any • Air powered tools can vibrate in damaged labels. use. Vibration, repetitive motions or uncomfortable positions over • Use accessories recommended by NAPA extended periods of time may be Professional Air Tools. harmful to your hands and arms. PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MANUAL FOR FUTURE REFERENCE.
-
Page 3: Air Supply
25 feet). Minimum hose diameter air line will cause damage to the reduces the speed of all air tools. should be 3/8" I.D. and fittings tool. Drain the air tank daily. Clean Low air pressure not only wastes should have the same inside the air inlet filter screen on at least time, but also costs money. Higher dimensions and be tightly secured. a weekly schedule. The pressure (over 90 psig; 6.2 bar) recommended hookup procedure raises performance beyond the can be viewed in the above figure. LUBRICATION Lubricate the air motor daily with squirted into the tool air inlet or reduction in the power of the tool. NAPA air tool oil. If no air line into the hose at the nearest oiler is used, run 1/2 ounce of oil connection to the air supply, then through the tool. The oil can be run the tool. Overfilling will cause a PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MANUAL FOR FUTURE REFERENCE. -
Page 4: Operation
All NAPA ProfessioNAl Air Tools must be repaired only by authorized NAPA ProfessioNAl Air Tool service Centers. This warranty does not cover damage to tools rising from alteration, abuse, misuse and does not cover any repairs made by anyone other than an authorized NAPA ProfessioNAl Air Tool Warranty Center. -
Page 5: Troubleshooting
TROUBLEShOOTINg IMPACT WRENCHES TOOL wILL NOT RUN, AIR fLOwS fREELY YOU ShOULd: FOR OIL LUBED WRENCHES fROm ExhAUST, SPINdLE TURNS fREELY - check for presence of clutch oil (where TOOL RUNS SLOwLY OR NOT AT ALL oil is specified for clutch) and remove oil — This is probably caused by: Build up of ANd/OR AIR fLOwS ONLY SLIghTLY fROm fill plug; tilt to drain all oil from clutch dirt or varnish on rotor vanes. ExhAUST — This is probably caused by: air case; refill with 30 weight SAE oil or that YOU ShOULd: Pour a generous amount flow blocked by dirt build-up; motor parts recommended by manufacturer, in the of air tool oil into air inlet. Operate trig-... -
Page 6: Parts Breakdown
6-715 PARTS BREAKDOWN 8" ANGLE POLISHER PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MANUAL FOR FUTURE REFERENCE. -
Page 7: Parts List
6-715 PARTS LIST 8" ANGLE POLISHER Item# Part # Description Qty. Air Inlet RS71601 Exhaust Bushing RS71602 Motor Housing RS71603 Handle Cover RS71605 Lever RS71606 Throttle Lever Pin RS71607 Throttle Valve Bushing RS71609 Valve Stem RS71610 O-Ring RS71611 Spring RS71612...